blob: 10bbfe1a22c0c07d80f8d74b9f87e3be531f56f9 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
|
#######
# @licence make begin@
# SPDX license identifier: MPL-2.0
#
# Copyright (C) 2011-2015, BMW AG"
#
# This file is part of GENIVI Project DLT - Diagnostic Log and Trace.
#
# This Source Code Form is subject to the terms of the
# Mozilla Public License (MPL), v. 2.0.
# If a copy of the MPL was not distributed with this file,
# You can obtain one at http://mozilla.org/MPL/2.0/.
#
# For further information see http://www.genivi.org/.
# @licence end@
#######
if(WITH_SYSTEMD)
set(SYSTEMD_CONFIGURATIONS_FILES_DIR ${CMAKE_INSTALL_PREFIX}/lib/systemd/system )
if(WITH_SYSTEMD_WATCHDOG)
set( DLT_WatchdogSec 2 )
message( STATUS "The systemd watchdog is enabled - timeout is set to ${DLT_WatchdogSec} seconds")
else(WITH_SYSTEMD_WATCHDOG)
set( DLT_WatchdogSec 0 )
message( STATUS "The systemd watchdog is disabled")
endif(WITH_SYSTEMD_WATCHDOG)
configure_file(${CMAKE_SOURCE_DIR}/systemd/dlt.service.cmake ${PROJECT_BINARY_DIR}/systemd/dlt.service)
message( STATUS "Configured systemd unit file:dlt.service" )
configure_file(${CMAKE_SOURCE_DIR}/systemd/dlt-system.service.cmake ${PROJECT_BINARY_DIR}/systemd/dlt-system.service)
message( STATUS "Configured systemd unit file:dlt-system.service" )
if(WITH_DLT_DBUS)
configure_file(${CMAKE_SOURCE_DIR}/systemd/dlt-dbus.service.cmake ${PROJECT_BINARY_DIR}/systemd/dlt-dbus.service)
message( STATUS "Configured systemd unit file:dlt-dbus.service" )
endif(WITH_DLT_DBUS)
configure_file(${CMAKE_SOURCE_DIR}/systemd/dlt-receive.service.cmake ${PROJECT_BINARY_DIR}/systemd/dlt-receive.service)
message( STATUS "Configured systemd unit file:dlt-receive.service" )
configure_file(${CMAKE_SOURCE_DIR}/systemd/dlt-example-user.service.cmake ${PROJECT_BINARY_DIR}/systemd/dlt-example-user.service)
message( STATUS "Configured systemd unit file:dlt-example-user.service" )
set( DLT_ADAPTOR_UDP_APPID "DUDP" )
set( DLT_ADAPTOR_UDP_CTID "DCTI" )
set( DLT_ADAPTOR_UDP_PORT 4712 )
configure_file(${CMAKE_SOURCE_DIR}/systemd/dlt-adaptor-udp.service.cmake ${PROJECT_BINARY_DIR}/systemd/dlt-adaptor-udp.service)
message( STATUS "Configured systemd unit file:dlt-adaptor-udp.service" )
message(STATUS "DLT adaptor udp configuration: APPID=${DLT_ADAPTOR_UDP_APPID} CTID=${DLT_ADAPTOR_UDP_CTID} PORT=${DLT_ADAPTOR_UDP_PORT}" )
install(FILES ${PROJECT_BINARY_DIR}/systemd/dlt.service DESTINATION ${SYSTEMD_CONFIGURATIONS_FILES_DIR} )
install(FILES ${PROJECT_BINARY_DIR}/systemd/dlt-system.service DESTINATION ${SYSTEMD_CONFIGURATIONS_FILES_DIR} )
install(FILES ${PROJECT_BINARY_DIR}/systemd/dlt-receive.service DESTINATION ${SYSTEMD_CONFIGURATIONS_FILES_DIR} )
if(WITH_DLT_DBUS)
install(FILES ${PROJECT_BINARY_DIR}/systemd/dlt-dbus.service DESTINATION ${SYSTEMD_CONFIGURATIONS_FILES_DIR} )
endif(WITH_DLT_DBUS)
if(WITH_DLT_EXAMPLES)
install(FILES ${PROJECT_BINARY_DIR}/systemd/dlt-example-user.service DESTINATION ${SYSTEMD_CONFIGURATIONS_FILES_DIR} )
endif(WITH_DLT_EXAMPLES)
install(FILES ${PROJECT_BINARY_DIR}/systemd/dlt-adaptor-udp.service DESTINATION ${SYSTEMD_CONFIGURATIONS_FILES_DIR} )
message(STATUS "Unit files will be installed to ${SYSTEMD_CONFIGURATIONS_FILES_DIR} after make install" )
endif(WITH_SYSTEMD)
|
