1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
|
## automake - create Makefile.in from Makefile.am
## Copyright (C) 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2003, 2004
## Free Software Foundation, Inc.
## This program is free software; you can redistribute it and/or modify
## it under the terms of the GNU General Public License as published by
## the Free Software Foundation; either version 2, or (at your option)
## any later version.
## This program is distributed in the hope that it will be useful,
## but WITHOUT ANY WARRANTY; without even the implied warranty of
## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
## GNU General Public License for more details.
## You should have received a copy of the GNU General Public License
## along with this program; if not, write to the Free Software
## Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
## 02110-1301, USA.
RECURSIVE_TARGETS += all-recursive check-recursive installcheck-recursive
RECURSIVE_CLEAN_TARGETS = mostlyclean-recursive clean-recursive \
distclean-recursive maintainer-clean-recursive
.PHONY: $(RECURSIVE_TARGETS) $(RECURSIVE_CLEAN_TARGETS)
.MAKE: $(RECURSIVE_TARGETS) $(RECURSIVE_CLEAN_TARGETS)
# This directory's subdirectories are mostly independent; you can cd
# into them and run `make' without going through this Makefile.
# To change the values of `make' variables: instead of editing Makefiles,
# (1) if the variable is set in `config.status', edit `config.status'
# (which will cause the Makefiles to be regenerated when you run `make');
# (2) otherwise, pass the desired values on the `make' command line.
$(RECURSIVE_TARGETS):
## Using $failcom allows "-k" to keep its natural meaning when running a
## recursive rule.
@failcom='exit 1'; \
for f in x $$MAKEFLAGS; do \
case $$f in \
*=* | --[!k]*);; \
*k*) failcom='fail=yes';; \
esac; \
done; \
dot_seen=no; \
target=`echo $@ | sed s/-recursive//`; \
list='$(SUBDIRS)'; for subdir in $$list; do \
echo "Making $$target in $$subdir"; \
if test "$$subdir" = "."; then \
dot_seen=yes; \
local_target="$$target-am"; \
else \
local_target="$$target"; \
fi; \
(cd $$subdir && $(MAKE) $(AM_MAKEFLAGS) $$local_target) \
|| eval $$failcom; \
done; \
if test "$$dot_seen" = "no"; then \
$(MAKE) $(AM_MAKEFLAGS) "$$target-am" || exit 1; \
fi; test -z "$$fail"
mostlyclean: mostlyclean-recursive
clean: clean-recursive
distclean: distclean-recursive
maintainer-clean: maintainer-clean-recursive
## We run all `clean' targets in reverse order. Why? It's an attempt
## to alleviate a problem that can happen when dependencies are
## enabled. In this case, the .P file in one directory can depend on
## some automatically generated header in an earlier directory. Since
## the dependencies are required before any target is examined, make
## bombs.
$(RECURSIVE_CLEAN_TARGETS):
## Using $failcom allows "-k" to keep its natural meaning when running a
## recursive rule.
@failcom='exit 1'; \
for f in x $$MAKEFLAGS; do \
case $$f in \
*=* | --[!k]*);; \
*k*) failcom='fail=yes';; \
esac; \
done; \
dot_seen=no; \
## For distclean and maintainer-clean we make sure to use the full
## list of subdirectories. We do this so that `configure; make
## distclean' really is a no-op, even if SUBDIRS is conditional. For
## other clean targets this doesn't matter.
case "$@" in \
distclean-* | maintainer-clean-*) list='$(DIST_SUBDIRS)' ;; \
*) list='$(SUBDIRS)' ;; \
esac; \
rev=''; for subdir in $$list; do \
if test "$$subdir" = "."; then :; else \
rev="$$subdir $$rev"; \
fi; \
done; \
## Always do `.' last.
rev="$$rev ."; \
target=`echo $@ | sed s/-recursive//`; \
for subdir in $$rev; do \
echo "Making $$target in $$subdir"; \
if test "$$subdir" = "."; then \
local_target="$$target-am"; \
else \
local_target="$$target"; \
fi; \
(cd $$subdir && $(MAKE) $(AM_MAKEFLAGS) $$local_target) \
|| eval $$failcom; \
done && test -z "$$fail"
|
