1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
|
## automake - create Makefile.in from Makefile.am
## Copyright (C) 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002,
## 2003, 2004, 2005 Free Software Foundation, Inc.
## This program is free software; you can redistribute it and/or modify
## it under the terms of the GNU General Public License as published by
## the Free Software Foundation; either version 2, or (at your option)
## any later version.
## This program is distributed in the hope that it will be useful,
## but WITHOUT ANY WARRANTY; without even the implied warranty of
## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
## GNU General Public License for more details.
## You should have received a copy of the GNU General Public License
## along with this program; if not, write to the Free Software
## Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
## 02110-1301, USA.
?GENERIC_INFO?%SOURCE_SUFFIX%%DEST_SUFFIX%:
?!GENERIC_INFO?%DEST_INFO_PREFIX%%DEST_SUFFIX%: %SOURCE_INFO% %DEPS%
## It is wrong to have `info' files dependent on %DIRSTAMP%, because
## `info' files are distributed and %DIRSTAMP% isn't: a distributed file
## should never be dependent upon a non-distributed built file.
## Therefore we ensure that %DIRSTAMP% exists in the rule.
?!INSRC??DIRSTAMP? @test -f %DIRSTAMP% || $(MAKE) $(AM_MAKEFLAGS) %DIRSTAMP%
## Back up the info files before running makeinfo. This is the cheapest
## way to ensure that
## 1) If the texinfo file shrinks (or if you start using --no-split),
## you'll not be left with some dead info files lying around -- dead
## files which would end up in the distribution.
## 2) If the texinfo file has some minor mistakes which cause makeinfo
## to fail, the info files are not removed. (They are needed by the
## developer while he writes documentation.)
## *.iNN files are used on DJGPP. See the comments in install-info-am
restore=: && backupdir="$(am__leading_dot)am$$$$" && \
?INSRC? am__cwd=`pwd` && cd $(srcdir) && \
rm -rf $$backupdir && mkdir $$backupdir && \
## If makeinfo is not installed we must not backup the files so
##`missing' can do its job and touch $@ if it exists.
if ($(MAKEINFO) --version) >/dev/null 2>&1; then \
for f in $@ $@-[0-9] $@-[0-9][0-9] $(@:.info=).i[0-9] $(@:.info=).i[0-9][0-9]; do \
if test -f $$f; then mv $$f $$backupdir; restore=mv; else :; fi; \
done; \
else :; fi && \
?INSRC? cd "$$am__cwd"; \
if $(MAKEINFO) $(AM_MAKEINFOFLAGS) $(MAKEINFOFLAGS) %MAKEINFOFLAGS% \
?!INSRC? -o $@ `test -f '%SOURCE_INFO%' || echo '$(srcdir)/'`%SOURCE_INFO%; \
?INSRC??!GENERIC_INFO? -o $@ $(srcdir)/%SOURCE_INFO%; \
?INSRC??GENERIC_INFO? -o $@ $<; \
then \
rc=0; \
?INSRC? cd $(srcdir); \
else \
rc=$$?; \
## Beware that backup info files might come from a subdirectory.
?INSRC? cd $(srcdir) && \
$$restore $$backupdir/* `echo "./$@" | sed 's|[^/]*$$||'`; \
fi; \
rm -rf $$backupdir; exit $$rc
INFO_DEPS += %DEST_INFO_PREFIX%%DEST_SUFFIX%
?GENERIC?%SOURCE_SUFFIX%.dvi:
?!GENERIC?%DEST_PREFIX%.dvi: %SOURCE% %DEPS% %DIRSTAMP%
TEXINPUTS="$(am__TEXINFO_TEX_DIR)$(PATH_SEPARATOR)$$TEXINPUTS" \
## Must set MAKEINFO like this so that version.texi will be found even
## if it is in srcdir (-I $(srcdir) is set in %MAKEINFOFLAGS%).
MAKEINFO='$(MAKEINFO) $(AM_MAKEINFOFLAGS) $(MAKEINFOFLAGS) %MAKEINFOFLAGS%' \
## Do not use `-o' unless necessary: it is only supported since Texinfo 4.1.
?GENERIC? $(TEXI2DVI) %SOURCE%
?!GENERIC? $(TEXI2DVI) -o $@ `test -f '%SOURCE%' || echo '$(srcdir)/'`%SOURCE%
?GENERIC?%SOURCE_SUFFIX%.pdf:
?!GENERIC?%DEST_PREFIX%.pdf: %SOURCE% %DEPS% %DIRSTAMP%
TEXINPUTS="$(am__TEXINFO_TEX_DIR)$(PATH_SEPARATOR)$$TEXINPUTS" \
## Must set MAKEINFO like this so that version.texi will be found even
## if it is in srcdir (-I $(srcdir) is set in %MAKEINFOFLAGS%).
MAKEINFO='$(MAKEINFO) $(AM_MAKEINFOFLAGS) $(MAKEINFOFLAGS) %MAKEINFOFLAGS%' \
## Do not use `-o' unless necessary: it is only supported since Texinfo 4.1.
?GENERIC? $(TEXI2PDF) %SOURCE%
?!GENERIC? $(TEXI2PDF) -o $@ `test -f '%SOURCE%' || echo '$(srcdir)/'`%SOURCE%
?GENERIC?%SOURCE_SUFFIX%.html:
?!GENERIC?%DEST_PREFIX%.html: %SOURCE% %DEPS% %DIRSTAMP%
## When --split (the default) is used, makeinfo will output a
## directory. However it will not update the time stamp of a
## previously existing directory, and when the names of the nodes
## in the manual change, it may leave unused pages. Our fix
## is to build under a temporary name, and replace the target on
## success.
rm -rf $(@:.html=.htp)
if $(MAKEINFOHTML) $(AM_MAKEINFOHTMLFLAGS) $(MAKEINFOFLAGS) %MAKEINFOFLAGS% \
?GENERIC? -o $(@:.html=.htp) %SOURCE%; \
?!GENERIC? -o $(@:.html=.htp) `test -f '%SOURCE%' || echo '$(srcdir)/'`%SOURCE%; \
then \
rm -rf $@; \
## Work around a bug in Texinfo 4.1 (-o foo.html outputs files in foo/
## instead of foo.html/).
if test ! -d $(@:.html=.htp) && test -d $(@:.html=); then \
mv $(@:.html=) $@; else mv $(@:.html=.htp) $@; fi; \
else \
if test ! -d $(@:.html=.htp) && test -d $(@:.html=); then \
rm -rf $(@:.html=); else rm -Rf $(@:.html=.htp) $@; fi; \
exit 1; \
fi
## If we are using the generic rules, we need separate dependencies.
## (Don't wonder about %DIRSTAMP% here, this is used only by non-generic
## rules.)
if %?GENERIC_INFO%
%DEST_INFO_PREFIX%%DEST_SUFFIX%: %SOURCE_REAL% %DEPS%
endif %?GENERIC_INFO%
if %?GENERIC%
%DEST_PREFIX%.dvi: %SOURCE_REAL% %DEPS%
%DEST_PREFIX%.pdf: %SOURCE_REAL% %DEPS%
%DEST_PREFIX%.html: %SOURCE_REAL% %DEPS%
endif %?GENERIC%
|
