volet: Initial EC image

Create the initial EC image for the volet variant by copying the
voxel reference board EC files into a new directory named for
the variant.

(Auto-Generated by create_initial_ec_image.sh version 1.5.0).

BUG=b:186334008
BRANCH=None
TEST=make BOARD=volet

Change-Id: I97cee656f4f12785110297afb323d2feac2b48d1
Signed-off-by: Ben Chen <ben.chen2@quanta.corp-partner.google.com>
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/2866925
Reviewed-by: Keith Short <keithshort@chromium.org>
Commit-Queue: Keith Short <keithshort@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/2874432
Tested-by: Abe Levkoy <alevkoy@chromium.org>
Reviewed-by: Abe Levkoy <alevkoy@chromium.org>
Commit-Queue: Abe Levkoy <alevkoy@chromium.org>

9 files changed, 1551 insertions, 0 deletions

diff --git a/board/volet/battery.c b/board/volet/battery.c
new file mode 100644
index 0000000000..2e4fb7dc71
--- /dev/null
+++ b/board/volet/battery.c
@@ -0,0 +1,125 @@
+/* Copyright 2021 The Chromium OS Authors. All rights reserved.
+ * Use of this source code is governed by a BSD-style license that can be
+ * found in the LICENSE file.
+ *
+ * Battery pack vendor provided charging profile
+ */
+
+#include "battery_fuel_gauge.h"
+#include "common.h"
+#include "util.h"
+
+/*
+ * Battery info for all Volteer battery types. Note that the fields
+ * start_charging_min/max and charging_min/max are not used for the charger.
+ * The effective temperature limits are given by discharging_min/max_c.
+ *
+ * Fuel Gauge (FG) parameters which are used for determining if the battery
+ * is connected, the appropriate ship mode (battery cutoff) command, and the
+ * charge/discharge FETs status.
+ *
+ * Ship mode (battery cutoff) requires 2 writes to the appropriate smart battery
+ * register. For some batteries, the charge/discharge FET bits are set when
+ * charging/discharging is active, in other types, these bits set mean that
+ * charging/discharging is disabled. Therefore, in addition to the mask for
+ * these bits, a disconnect value must be specified. Note that for TI fuel
+ * gauge, the charge/discharge FET status is found in Operation Status (0x54),
+ * but a read of Manufacturer Access (0x00) will return the lower 16 bits of
+ * Operation status which contains the FET status bits.
+ *
+ * The assumption for battery types supported is that the charge/discharge FET
+ * status can be read with a sb_read() command and therefore, only the register
+ * address, mask, and disconnect value need to be provided.
+ */
+const struct board_batt_params board_battery_info[] = {
+	/* AP19B8M */
+	[BATTERY_AP19B8M] = {
+		.fuel_gauge = {
+			.manuf_name = "LGC KT0030G024",
+			.ship_mode = {
+				.reg_addr = 0x3A,
+				.reg_data = { 0xC574, 0xC574 },
+			},
+			.fet = {
+				.reg_addr = 0x43,
+				.reg_mask = 0x0001,
+				.disconnect_val = 0x0,
+				.cfet_mask = 0x0002,
+				.cfet_off_val = 0x0000,
+			}
+		},
+		.batt_info = {
+			.voltage_max          = 13350,
+			.voltage_normal       = 11610,
+			.voltage_min          = 9000,
+			.precharge_current    = 256,
+			.start_charging_min_c = 0,
+			.start_charging_max_c = 50,
+			.charging_min_c       = 0,
+			.charging_max_c       = 60,
+			.discharging_min_c    = -20,
+			.discharging_max_c    = 75,
+		},
+	},
+	/* LGC AP18C8K Battery Information */
+	 [BATTERY_LGC_AP18C8K] = {
+		.fuel_gauge = {
+			.manuf_name = "LGC KT0030G020",
+			.ship_mode = {
+				.reg_addr = 0x3A,
+				.reg_data = { 0xC574, 0xC574 },
+			},
+			.fet = {
+				.reg_addr = 0x43,
+				.reg_mask = 0x0001,
+				.disconnect_val = 0x0,
+				.cfet_mask = 0x0002,
+				.cfet_off_val = 0x0000,
+			},
+		},
+		.batt_info = {
+			.voltage_max            = 13050,
+			.voltage_normal         = 11250,
+			.voltage_min            = 9000,
+			.precharge_current      = 256,
+			.start_charging_min_c   = 0,
+			.start_charging_max_c   = 50,
+			.charging_min_c         = 0,
+			.charging_max_c         = 60,
+			.discharging_min_c      = -20,
+			.discharging_max_c      = 75,
+		},
+	},
+	/* COSMX AP20CBL Battery Information */
+	 [BATTERY_COSMX_AP20CBL] = {
+		.fuel_gauge = {
+			.manuf_name = "COSMX KT0030B002",
+			.device_name = "AP20CBL",
+			.ship_mode = {
+				.reg_addr = 0x3A,
+				.reg_data = { 0xC574, 0xC574 },
+			},
+			.fet = {
+				.mfgacc_support = 1,
+				.reg_addr = 0x0,
+				.reg_mask = 0x2000,
+				.disconnect_val = 0x2000,
+			},
+		},
+		.batt_info = {
+			.voltage_max            = 13200,
+			.voltage_normal         = 11550,
+			.voltage_min            = 9000,
+			.precharge_current      = 256,
+			.start_charging_min_c   = 0,
+			.start_charging_max_c   = 50,
+			.charging_min_c         = 0,
+			.charging_max_c         = 60,
+			.discharging_min_c      = -20,
+			.discharging_max_c      = 75,
+		},
+	},
+};
+BUILD_ASSERT(ARRAY_SIZE(board_battery_info) == BATTERY_TYPE_COUNT);
+
+const enum battery_type DEFAULT_BATTERY_TYPE = BATTERY_AP19B8M;
diff --git a/board/volet/board.c b/board/volet/board.c
new file mode 100644
index 0000000000..d366e25eca
--- /dev/null
+++ b/board/volet/board.c
@@ -0,0 +1,495 @@
+/* Copyright 2021 The Chromium OS Authors. All rights reserved.
+ * Use of this source code is governed by a BSD-style license that can be
+ * found in the LICENSE file.
+ */
+
+/* Volteer board-specific configuration */
+#include "bb_retimer.h"
+#include "button.h"
+#include "common.h"
+#include "accelgyro.h"
+#include "cbi_ec_fw_config.h"
+#include "driver/accel_bma2x2.h"
+#include "driver/accelgyro_bmi160.h"
+#include "driver/als_tcs3400.h"
+#include "driver/bc12/pi3usb9201.h"
+#include "driver/ppc/syv682x.h"
+#include "driver/tcpm/tcpci.h"
+#include "driver/tcpm/tusb422.h"
+#include "driver/tcpm/rt1715.h"
+#include "driver/retimer/bb_retimer.h"
+#include "driver/sync.h"
+#include "extpower.h"
+#include "fan.h"
+#include "fan_chip.h"
+#include "gpio.h"
+#include "hooks.h"
+#include "keyboard_scan.h"
+#include "lid_switch.h"
+#include "power.h"
+#include "power_button.h"
+#include "pwm.h"
+#include "pwm_chip.h"
+#include "switch.h"
+#include "system.h"
+#include "task.h"
+#include "tablet_mode.h"
+#include "throttle_ap.h"
+#include "uart.h"
+#include "usb_mux.h"
+#include "usb_pd.h"
+#include "usb_pd_tbt.h"
+#include "usb_pd_tcpm.h"
+#include "usbc_ppc.h"
+#include "util.h"
+
+#include "gpio_list.h" /* Must come after other header files. */
+
+#define CPRINTS(format, args...) cprints(CC_CHIPSET, format, ## args)
+
+static const struct ec_response_keybd_config zbu_new_kb = {
+	.num_top_row_keys = 10,
+	.action_keys = {
+		TK_BACK,
+		TK_REFRESH,
+		TK_FULLSCREEN,
+		TK_OVERVIEW,
+		TK_SNAPSHOT,
+		TK_BRIGHTNESS_DOWN,
+		TK_BRIGHTNESS_UP,
+		TK_VOL_MUTE,
+		TK_VOL_DOWN,
+		TK_VOL_UP,
+	},
+	.capabilities = KEYBD_CAP_SCRNLOCK_KEY,
+};
+
+static const struct ec_response_keybd_config zbu_old_kb = {
+	.num_top_row_keys = 10,
+	.action_keys = {
+		TK_BACK,		/* T1 */
+		TK_FORWARD,		/* T2 */
+		TK_REFRESH,		/* T3 */
+		TK_FULLSCREEN,		/* T4 */
+		TK_OVERVIEW,		/* T5 */
+		TK_BRIGHTNESS_DOWN,	/* T6 */
+		TK_BRIGHTNESS_UP,	/* T7 */
+		TK_VOL_MUTE,		/* T8 */
+		TK_VOL_DOWN,		/* T9 */
+		TK_VOL_UP,		/* T10 */
+	},
+	.capabilities = KEYBD_CAP_SCRNLOCK_KEY,
+};
+
+__override
+const struct ec_response_keybd_config *board_vivaldi_keybd_config(void)
+{
+	if (get_board_id() > 2)
+		return &zbu_new_kb;
+	else
+		return &zbu_old_kb;
+}
+
+/* Keyboard scan setting */
+struct keyboard_scan_config keyscan_config = {
+	/* Increase from 50 us, because KSO_02 passes through the H1. */
+	.output_settle_us = 80,
+	/* Other values should be the same as the default configuration. */
+	.debounce_down_us = 9 * MSEC,
+	.debounce_up_us = 30 * MSEC,
+	.scan_period_us = 3 * MSEC,
+	.min_post_scan_delay_us = 1000,
+	.poll_timeout_us = 100 * MSEC,
+	.actual_key_mask = {
+		0x14, 0xff, 0xff, 0xff, 0xff, 0xf5, 0xff,
+		0xa4, 0xff, 0xfe, 0x55, 0xfa, 0xca  /* full set */
+	},
+};
+
+__override uint32_t board_override_feature_flags0(uint32_t flags0)
+{
+	/*
+	 * Remove keyboard backlight feature for devices that don't support it.
+	 */
+	if (!ec_cfg_has_keyboard_backlight())
+		return (flags0 & ~EC_FEATURE_MASK_0(EC_FEATURE_PWM_KEYB));
+	else
+		return flags0;
+}
+
+/******************************************************************************/
+/*
+ * FW_CONFIG defaults for Voxel if the CBI data is not initialized.
+ */
+union volteer_cbi_fw_config fw_config_defaults = {
+	.usb_db = DB_USB4_GEN3,
+};
+
+/******************************************************************************/
+/* Physical fans. These are logically separate from pwm_channels. */
+
+const struct fan_conf fan_conf_0 = {
+	.flags = FAN_USE_RPM_MODE,
+	.ch = MFT_CH_0,	/* Use MFT id to control fan */
+	.pgood_gpio = -1,
+	.enable_gpio = GPIO_EN_PP5000_FAN,
+};
+
+/*
+ * Fan specs from datasheet:
+ * Max speed 5900 rpm (+/- 7%), minimum duty cycle 30%.
+ * Minimum speed not specified by RPM. Set minimum RPM to max speed (with
+ * margin) x 30%.
+ *    5900 x 1.07 x 0.30 = 1894, round up to 1900
+ * reference that temperature and fan settings
+ * are derived from data in b/167523658#39
+ */
+const struct fan_rpm fan_rpm_0 = {
+	.rpm_min = 2100,
+	.rpm_start = 2100,
+	.rpm_max = 5800,
+};
+
+const struct fan_t fans[FAN_CH_COUNT] = {
+	[FAN_CH_0] = {
+		.conf = &fan_conf_0,
+		.rpm = &fan_rpm_0,
+	},
+};
+
+/******************************************************************************/
+/* EC thermal management configuration */
+
+/*
+ * Reference that temperature and fan settings
+ * are derived from data in b/167523658#39
+ */
+const static struct ec_thermal_config thermal_cpu = {
+	.temp_host = {
+		[EC_TEMP_THRESH_HIGH] = C_TO_K(75),
+		[EC_TEMP_THRESH_HALT] = C_TO_K(85),
+	},
+	.temp_host_release = {
+		[EC_TEMP_THRESH_HIGH] = C_TO_K(68),
+	},
+	.temp_fan_off = C_TO_K(25),
+	.temp_fan_max = C_TO_K(90),
+};
+
+struct ec_thermal_config thermal_params[] = {
+	[TEMP_SENSOR_1_CHARGER]			= thermal_cpu,
+	[TEMP_SENSOR_2_PP3300_REGULATOR]	= thermal_cpu,
+	[TEMP_SENSOR_3_DDR_SOC]			= thermal_cpu,
+	[TEMP_SENSOR_4_FAN]			= thermal_cpu,
+};
+BUILD_ASSERT(ARRAY_SIZE(thermal_params) == TEMP_SENSOR_COUNT);
+
+/******************************************************************************/
+/* MFT channels. These are logically separate from pwm_channels. */
+const struct mft_t mft_channels[] = {
+	[MFT_CH_0] = {
+		.module = NPCX_MFT_MODULE_1,
+		.clk_src = TCKC_LFCLK,
+		.pwm_id = PWM_CH_FAN,
+	},
+};
+BUILD_ASSERT(ARRAY_SIZE(mft_channels) == MFT_CH_COUNT);
+
+/******************************************************************************/
+/* I2C port map configuration */
+const struct i2c_port_t i2c_ports[] = {
+	{
+		.name = "sensor",
+		.port = I2C_PORT_SENSOR,
+		.kbps = 400,
+		.scl = GPIO_EC_I2C0_SENSOR_SCL,
+		.sda = GPIO_EC_I2C0_SENSOR_SDA,
+	},
+	{
+		.name = "usb_c0",
+		.port = I2C_PORT_USB_C0,
+		.kbps = 1000,
+		.scl = GPIO_EC_I2C1_USB_C0_SCL,
+		.sda = GPIO_EC_I2C1_USB_C0_SDA,
+	},
+	{
+		.name = "usb_c1",
+		.port = I2C_PORT_USB_C1,
+		.kbps = 1000,
+		.scl = GPIO_EC_I2C2_USB_C1_SCL,
+		.sda = GPIO_EC_I2C2_USB_C1_SDA,
+	},
+	{
+		.name = "usb_0_mix",
+		.port = I2C_PORT_USB_0_MIX,
+		.kbps = 100,
+		.scl = GPIO_EC_I2C3_USB_1_MIX_SCL,
+		.sda = GPIO_EC_I2C3_USB_1_MIX_SDA,
+	},
+	{
+		.name = "usb_1_mix",
+		.port = I2C_PORT_USB_1_MIX,
+		.kbps = 100,
+		.scl = GPIO_EC_I2C4_USB_1_MIX_SCL,
+		.sda = GPIO_EC_I2C4_USB_1_MIX_SDA,
+	},
+	{
+		.name = "power",
+		.port = I2C_PORT_POWER,
+		.kbps = 100,
+		.scl = GPIO_EC_I2C5_POWER_SCL,
+		.sda = GPIO_EC_I2C5_POWER_SDA,
+	},
+	{
+		.name = "eeprom",
+		.port = I2C_PORT_EEPROM,
+		.kbps = 400,
+		.scl = GPIO_EC_I2C7_EEPROM_SCL,
+		.sda = GPIO_EC_I2C7_EEPROM_SDA,
+	},
+};
+const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports);
+
+/******************************************************************************/
+/* PWM configuration */
+const struct pwm_t pwm_channels[] = {
+	[PWM_CH_FAN] = {
+		.channel = 5,
+		.flags = PWM_CONFIG_OPEN_DRAIN,
+		.freq = 25000
+	},
+	[PWM_CH_KBLIGHT] = {
+		.channel = 3,
+		.flags = 0,
+		/*
+		 * Set PWM frequency to multiple of 50 Hz and 60 Hz to prevent
+		 * flicker. Higher frequencies consume similar average power to
+		 * lower PWM frequencies, but higher frequencies record a much
+		 * lower maximum power.
+		 */
+		.freq = 2400,
+	},
+};
+BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT);
+
+static void kb_backlight_enable(void)
+{
+	if (ec_cfg_has_keyboard_backlight())
+		gpio_set_level(GPIO_EC_KB_BL_EN, 1);
+}
+DECLARE_HOOK(HOOK_CHIPSET_RESUME, kb_backlight_enable, HOOK_PRIO_DEFAULT);
+
+static void kb_backlight_disable(void)
+{
+	if (ec_cfg_has_keyboard_backlight())
+		gpio_set_level(GPIO_EC_KB_BL_EN, 0);
+}
+DECLARE_HOOK(HOOK_CHIPSET_SUSPEND, kb_backlight_disable, HOOK_PRIO_DEFAULT);
+
+/* Config TCPC dynamic by Board version */
+static void setup_board_tcpc(void)
+{
+	uint8_t board_id = get_board_id();
+
+	if (board_id == 0) {
+		/* config typec C0 prot TUSB422 TCPC */
+		tcpc_config[USBC_PORT_C0].i2c_info.addr_flags
+			= TUSB422_I2C_ADDR_FLAGS;
+		tcpc_config[USBC_PORT_C0].drv = &tusb422_tcpm_drv;
+		/* config typec C1 prot TUSB422 TCPC */
+		tcpc_config[USBC_PORT_C1].i2c_info.addr_flags
+			= TUSB422_I2C_ADDR_FLAGS;
+		tcpc_config[USBC_PORT_C1].drv = &tusb422_tcpm_drv;
+	}
+}
+
+void board_reset_pd_mcu(void)
+{
+	/*
+	 * Only the Burnside Bridge retimers provide a reset pin, but this is
+	 * already handled by the bb_retimer.c driver.
+	 */
+}
+
+/******************************************************************************/
+/* USB-A charging control */
+
+const int usb_port_enable[USB_PORT_COUNT] = {
+	GPIO_EN_PP5000_USBA,
+};
+
+/******************************************************************************/
+/* USBC PPC configuration */
+struct ppc_config_t ppc_chips[] = {
+	[USBC_PORT_C0] = {
+		.i2c_port = I2C_PORT_USB_C0,
+		.i2c_addr_flags = SYV682X_ADDR0_FLAGS,
+		.drv = &syv682x_drv,
+		.frs_en = GPIO_USB_C0_FRS_EN,
+	},
+	[USBC_PORT_C1] = {
+		.i2c_port = I2C_PORT_USB_C1,
+		.i2c_addr_flags = SYV682X_ADDR0_FLAGS,
+		.drv = &syv682x_drv,
+		.frs_en = GPIO_USB_C1_FRS_EN,
+	},
+};
+BUILD_ASSERT(ARRAY_SIZE(ppc_chips) == USBC_PORT_COUNT);
+unsigned int ppc_cnt = ARRAY_SIZE(ppc_chips);
+
+/******************************************************************************/
+/* PPC support routines */
+void ppc_interrupt(enum gpio_signal signal)
+{
+	switch (signal) {
+	case GPIO_USB_C0_PPC_INT_ODL:
+		syv682x_interrupt(USBC_PORT_C0);
+		break;
+	case GPIO_USB_C1_PPC_INT_ODL:
+		syv682x_interrupt(USBC_PORT_C1);
+	default:
+		break;
+	}
+}
+
+/* Disable FRS on boards with the SYV682A. FRS only works on the SYV682B. */
+void setup_board_ppc(void)
+{
+	uint8_t board_id = get_board_id();
+
+	if (board_id < 2) {
+		ppc_chips[USBC_PORT_C0].frs_en = 0;
+		ppc_chips[USBC_PORT_C1].frs_en = 0;
+	}
+}
+
+__override void board_cbi_init(void)
+{
+	setup_board_tcpc();
+	setup_board_ppc();
+}
+
+/******************************************************************************/
+/* BC1.2 charger detect configuration */
+const struct pi3usb9201_config_t pi3usb9201_bc12_chips[] = {
+	[USBC_PORT_C0] = {
+		.i2c_port = I2C_PORT_USB_C0,
+		.i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS,
+	},
+	[USBC_PORT_C1] = {
+		.i2c_port = I2C_PORT_USB_C1,
+		.i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS,
+	},
+};
+BUILD_ASSERT(ARRAY_SIZE(pi3usb9201_bc12_chips) == USBC_PORT_COUNT);
+
+/******************************************************************************/
+/* USBC TCPC configuration */
+struct tcpc_config_t tcpc_config[] = {
+	[USBC_PORT_C0] = {
+		.bus_type = EC_BUS_TYPE_I2C,
+		.i2c_info = {
+			.port = I2C_PORT_USB_C0,
+			.addr_flags = RT1715_I2C_ADDR_FLAGS,
+		},
+		.drv = &rt1715_tcpm_drv,
+	},
+	[USBC_PORT_C1] = {
+		.bus_type = EC_BUS_TYPE_I2C,
+		.i2c_info = {
+			.port = I2C_PORT_USB_C1,
+			.addr_flags = RT1715_I2C_ADDR_FLAGS,
+		},
+		.drv = &rt1715_tcpm_drv,
+	},
+};
+BUILD_ASSERT(ARRAY_SIZE(tcpc_config) == USBC_PORT_COUNT);
+BUILD_ASSERT(CONFIG_USB_PD_PORT_MAX_COUNT == USBC_PORT_COUNT);
+
+/******************************************************************************/
+/* USBC mux configuration - Tiger Lake includes internal mux */
+struct usb_mux usbc0_tcss_usb_mux = {
+	.usb_port = USBC_PORT_C0,
+	.driver = &virtual_usb_mux_driver,
+	.hpd_update = &virtual_hpd_update,
+};
+struct usb_mux usbc1_tcss_usb_mux = {
+	.usb_port = USBC_PORT_C1,
+	.driver = &virtual_usb_mux_driver,
+	.hpd_update = &virtual_hpd_update,
+};
+
+struct usb_mux usb_muxes[] = {
+	[USBC_PORT_C0] = {
+		.usb_port = USBC_PORT_C0,
+		.next_mux = &usbc0_tcss_usb_mux,
+		.driver = &bb_usb_retimer,
+		.i2c_port = I2C_PORT_USB_0_MIX,
+		.i2c_addr_flags = USBC_PORT_C0_BB_RETIMER_I2C_ADDR,
+	},
+	[USBC_PORT_C1] = {
+		.usb_port = USBC_PORT_C1,
+		.next_mux = &usbc1_tcss_usb_mux,
+		.driver = &bb_usb_retimer,
+		.i2c_port = I2C_PORT_USB_1_MIX,
+		.i2c_addr_flags = USBC_PORT_C1_BB_RETIMER_I2C_ADDR,
+	},
+};
+BUILD_ASSERT(ARRAY_SIZE(usb_muxes) == USBC_PORT_COUNT);
+
+struct bb_usb_control bb_controls[] = {
+	[USBC_PORT_C0] = {
+		.usb_ls_en_gpio = GPIO_USB_C0_LS_EN,
+		.retimer_rst_gpio = GPIO_USB_C0_RT_RST_ODL,
+	},
+	[USBC_PORT_C1] = {
+		.usb_ls_en_gpio = GPIO_USB_C1_LS_EN,
+		.retimer_rst_gpio = GPIO_USB_C1_RT_RST_ODL,
+	},
+};
+BUILD_ASSERT(ARRAY_SIZE(bb_controls) == USBC_PORT_COUNT);
+
+static void board_tcpc_init(void)
+{
+	/* Don't reset TCPCs after initial reset */
+	if (!system_jumped_late())
+		board_reset_pd_mcu();
+
+	/* Enable PPC interrupts. */
+	gpio_enable_interrupt(GPIO_USB_C0_PPC_INT_ODL);
+	gpio_enable_interrupt(GPIO_USB_C1_PPC_INT_ODL);
+
+	/* Enable TCPC interrupts. */
+	gpio_enable_interrupt(GPIO_USB_C0_TCPC_INT_ODL);
+	gpio_enable_interrupt(GPIO_USB_C1_TCPC_INT_ODL);
+
+	/* Enable BC1.2 interrupts. */
+	gpio_enable_interrupt(GPIO_USB_C0_BC12_INT_ODL);
+	gpio_enable_interrupt(GPIO_USB_C1_BC12_INT_ODL);
+}
+DECLARE_HOOK(HOOK_INIT, board_tcpc_init, HOOK_PRIO_INIT_CHIPSET);
+
+/******************************************************************************/
+/* TCPC support routines */
+uint16_t tcpc_get_alert_status(void)
+{
+	uint16_t status = 0;
+
+	/*
+	 * Check which port has the ALERT line set
+	 */
+	if (!gpio_get_level(GPIO_USB_C0_TCPC_INT_ODL))
+		status |= PD_STATUS_TCPC_ALERT_0;
+	if (!gpio_get_level(GPIO_USB_C1_TCPC_INT_ODL))
+		status |= PD_STATUS_TCPC_ALERT_1;
+
+	return status;
+}
+
+int ppc_get_alert_status(int port)
+{
+	if (port == USBC_PORT_C0)
+		return gpio_get_level(GPIO_USB_C0_PPC_INT_ODL) == 0;
+	else
+		return gpio_get_level(GPIO_USB_C1_PPC_INT_ODL) == 0;
+}
diff --git a/board/volet/board.h b/board/volet/board.h
new file mode 100644
index 0000000000..6793f4ae9f
--- /dev/null
+++ b/board/volet/board.h
@@ -0,0 +1,199 @@
+/* Copyright 2021 The Chromium OS Authors. All rights reserved.
+ * Use of this source code is governed by a BSD-style license that can be
+ * found in the LICENSE file.
+ */
+
+/* Volteer board configuration */
+
+#ifndef __CROS_EC_BOARD_H
+#define __CROS_EC_BOARD_H
+
+/* Baseboard features */
+#include "baseboard.h"
+
+/* Optional features */
+#undef NPCX7_PWM1_SEL
+#define NPCX7_PWM1_SEL    0    /* GPIO C2 is not used as PWM1. */
+
+/*
+ * The RAM and flash size combination on the the NPCX797FC does not leave
+ * any unused flash space that can be used to store the .init_rom section.
+ */
+#undef CONFIG_CHIP_INIT_ROM_REGION
+
+#define CONFIG_VBOOT_EFS2
+
+#define CONFIG_POWER_BUTTON
+
+#undef CONFIG_UART_TX_BUF_SIZE
+#define CONFIG_UART_TX_BUF_SIZE 4096
+
+/* Chipset features */
+#define CONFIG_POWER_PP5000_CONTROL
+
+/* LED defines */
+#define CONFIG_LED_ONOFF_STATES
+
+/* Keyboard features */
+#define CONFIG_KEYBOARD_REFRESH_ROW3
+
+/* Keyboard backliht */
+#define CONFIG_PWM
+#define CONFIG_PWM_KBLIGHT
+
+/* Sensors */
+#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT
+/* BMI160 Base accel/gyro */
+#define CONFIG_ACCELGYRO_BMI160
+#define CONFIG_ACCELGYRO_ICM426XX	/* Base accel second source*/
+#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
+	TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
+#define CONFIG_ACCELGYRO_ICM426XX_INT_EVENT \
+	TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
+
+/* Lid operates in forced mode, base in FIFO */
+#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)
+
+/* BMA253 Lid accel */
+#define CONFIG_ACCEL_KX022	/* Lid accel */
+#define CONFIG_ACCEL_BMA255
+#define CONFIG_LID_ANGLE
+#define CONFIG_LID_ANGLE_UPDATE
+#define CONFIG_LID_ANGLE_SENSOR_BASE	BASE_ACCEL
+#define CONFIG_LID_ANGLE_SENSOR_LID	LID_ACCEL
+
+/* USB Type C and USB PD defines */
+#define CONFIG_USB_PD_PORT_MAX_COUNT			2
+
+#define PD_POWER_SUPPLY_TURN_ON_DELAY	30000 /* us */
+#define PD_POWER_SUPPLY_TURN_OFF_DELAY	30000 /* us */
+
+/*
+ * SN5S30 PPC supports up to 24V VBUS source and sink, however passive USB-C
+ * cables only support up to 60W.
+ */
+#define PD_OPERATING_POWER_MW	15000
+#define PD_MAX_POWER_MW		60000
+#define PD_MAX_CURRENT_MA	3000
+#define PD_MAX_VOLTAGE_MV	20000
+
+#define CONFIG_USB_PD_REQUIRE_AP_MODE_ENTRY
+#ifdef BOARD_VOXEL_ECMODEENTRY
+#undef CONFIG_USB_PD_REQUIRE_AP_MODE_ENTRY
+#endif
+
+/* Enabling Thunderbolt-compatible mode */
+#define CONFIG_USB_PD_TBT_COMPAT_MODE
+
+/* Enabling USB4 mode */
+#define CONFIG_USB_PD_USB4
+#define USBC_PORT_C0_BB_RETIMER_I2C_ADDR	0x40
+#define USBC_PORT_C1_BB_RETIMER_I2C_ADDR	0x41
+
+/* USB Type A Features */
+#define USB_PORT_COUNT			1
+#define CONFIG_USB_PORT_POWER_DUMB
+
+/* USBC PPC*/
+#define CONFIG_USBC_PPC_SYV682X		/* USBC port C0/C1 */
+#define CONFIG_USB_PD_FRS_PPC
+
+/* BC 1.2 */
+
+/* TCPC */
+#define CONFIG_USB_PD_TCPM_RT1715
+
+/* Volume Button feature */
+
+/* Fan features */
+
+/* charger defines */
+#define CONFIG_CHARGER_SENSE_RESISTOR		10
+#define CONFIG_CHARGER_SENSE_RESISTOR_AC	10
+
+/*
+ * Macros for GPIO signals used in common code that don't match the
+ * schematic names. Signal names in gpio.inc match the schematic and are
+ * then redefined here to so it's more clear which signal is being used for
+ * which purpose.
+ */
+#define GPIO_AC_PRESENT			GPIO_ACOK_OD
+#define GPIO_EC_INT_L			GPIO_EC_PCH_INT_ODL
+#define GPIO_EN_PP5000			GPIO_EN_PP5000_A
+#define GPIO_ENTERING_RW		GPIO_EC_ENTERING_RW
+#define GPIO_LID_OPEN			GPIO_EC_LID_OPEN
+#define GPIO_KBD_KSO2			GPIO_EC_KSO_02_INV
+#define GPIO_PACKET_MODE_EN		GPIO_EC_H1_PACKET_MODE
+#define GPIO_PCH_WAKE_L			GPIO_EC_PCH_WAKE_ODL
+#define GPIO_PCH_PWRBTN_L		GPIO_EC_PCH_PWR_BTN_ODL
+#define GPIO_PCH_RSMRST_L		GPIO_EC_PCH_RSMRST_ODL
+#define GPIO_PCH_RTCRST			GPIO_EC_PCH_RTCRST
+#define GPIO_PCH_SLP_S0_L		GPIO_SLP_S0_L
+#define GPIO_PCH_SLP_S3_L		GPIO_SLP_S3_L
+#define GPIO_PCH_DSW_PWROK		GPIO_EC_PCH_DSW_PWROK
+#define GPIO_POWER_BUTTON_L		GPIO_H1_EC_PWR_BTN_ODL
+#define GPIO_RSMRST_L_PGOOD		GPIO_PG_EC_RSMRST_ODL
+#define GPIO_CPU_PROCHOT		GPIO_EC_PROCHOT_ODL
+#define GPIO_SYS_RESET_L		GPIO_SYS_RST_ODL
+#define GPIO_WP_L			GPIO_EC_WP_L
+#define GPIO_USB_C1_BC12_INT_ODL	GPIO_USB_C1_MIX_INT_ODL
+#define GPIO_VOLUME_UP_L		GPIO_EC_VOLUP_BTN_ODL
+#define GPIO_VOLUME_DOWN_L		GPIO_EC_VOLDN_BTN_ODL
+#define GMR_TABLET_MODE_GPIO_L		GPIO_TABLET_MODE_L
+
+/* I2C Bus Configuration */
+#define CONFIG_I2C
+#define I2C_PORT_ACCEL		I2C_PORT_SENSOR
+#define I2C_PORT_SENSOR		NPCX_I2C_PORT0_0
+#define I2C_PORT_USB_C0		NPCX_I2C_PORT1_0
+#define I2C_PORT_USB_C1		NPCX_I2C_PORT2_0
+#define I2C_PORT_USB_0_MIX	NPCX_I2C_PORT3_0
+#define I2C_PORT_USB_1_MIX	NPCX_I2C_PORT4_1
+#define I2C_PORT_POWER		NPCX_I2C_PORT5_0
+#define I2C_PORT_EEPROM		NPCX_I2C_PORT7_0
+
+#define I2C_PORT_BATTERY	I2C_PORT_POWER
+#define I2C_PORT_CHARGER	I2C_PORT_EEPROM
+
+#define I2C_ADDR_EEPROM_FLAGS	0x50
+#define CONFIG_I2C_CONTROLLER
+
+
+#ifndef __ASSEMBLER__
+
+#include "gpio_signal.h"
+#include "registers.h"
+
+enum battery_type {
+	BATTERY_AP19B8M,
+	BATTERY_LGC_AP18C8K,
+	BATTERY_COSMX_AP20CBL,
+	BATTERY_TYPE_COUNT,
+};
+
+enum pwm_channel {
+	PWM_CH_FAN,
+	PWM_CH_KBLIGHT,
+	PWM_CH_COUNT
+};
+
+enum sensor_id {
+	LID_ACCEL = 0,
+	BASE_ACCEL,
+	BASE_GYRO,
+	SENSOR_COUNT,
+};
+
+enum usbc_port {
+	USBC_PORT_C0 = 0,
+	USBC_PORT_C1,
+	USBC_PORT_COUNT
+};
+
+void board_reset_pd_mcu(void);
+
+void motion_interrupt(enum gpio_signal signal);
+
+#endif /* !__ASSEMBLER__ */
+
+#endif /* __CROS_EC_BOARD_H */
diff --git a/board/volet/build.mk b/board/volet/build.mk
new file mode 100644
index 0000000000..546bcba8d2
--- /dev/null
+++ b/board/volet/build.mk
@@ -0,0 +1,17 @@
+# -*- makefile -*-
+# Copyright 2021 The Chromium OS Authors. All rights reserved.
+# Use of this source code is governed by a BSD-style license that can be
+# found in the LICENSE file.
+#
+# Board specific files build
+#
+
+CHIP:=npcx
+CHIP_FAMILY:=npcx7
+CHIP_VARIANT:=npcx7m7fc
+BASEBOARD:=volteer
+
+board-y=board.o
+board-y+=battery.o
+board-y+=led.o
+board-y+=sensors.o
diff --git a/board/volet/ec.tasklist b/board/volet/ec.tasklist
new file mode 100644
index 0000000000..e76bd368eb
--- /dev/null
+++ b/board/volet/ec.tasklist
@@ -0,0 +1,26 @@
+/* Copyright 2021 The Chromium OS Authors. All rights reserved.
+ * Use of this source code is governed by a BSD-style license that can be
+ * found in the LICENSE file.
+ */
+
+/*
+ * See CONFIG_TASK_LIST in config.h for details.
+ */
+
+#define CONFIG_TASK_LIST \
+	TASK_ALWAYS(HOOKS, hook_task, NULL, LARGER_TASK_STACK_SIZE) \
+	TASK_ALWAYS(CHG_RAMP, chg_ramp_task, NULL, TASK_STACK_SIZE) \
+	TASK_ALWAYS(USB_CHG_P0, usb_charger_task, 0, TASK_STACK_SIZE) \
+	TASK_ALWAYS(USB_CHG_P1, usb_charger_task, 0, TASK_STACK_SIZE) \
+	TASK_ALWAYS(CHARGER, charger_task, NULL, VENTI_TASK_STACK_SIZE) \
+	TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \
+	TASK_NOTEST(KEYPROTO, keyboard_protocol_task, NULL, TASK_STACK_SIZE) \
+	TASK_NOTEST(CHIPSET, chipset_task, NULL, LARGER_TASK_STACK_SIZE) \
+	TASK_ALWAYS(HOSTCMD, host_command_task, NULL, LARGER_TASK_STACK_SIZE) \
+	TASK_ALWAYS(CONSOLE, console_task, NULL, VENTI_TASK_STACK_SIZE) \
+	TASK_ALWAYS(POWERBTN, power_button_task, NULL, LARGER_TASK_STACK_SIZE) \
+	TASK_NOTEST(KEYSCAN, keyboard_scan_task, NULL, TASK_STACK_SIZE) \
+	TASK_ALWAYS(PD_C0, pd_task, NULL, VENTI_TASK_STACK_SIZE) \
+	TASK_ALWAYS(PD_C1, pd_task, NULL, VENTI_TASK_STACK_SIZE) \
+	TASK_ALWAYS(PD_INT_C0, pd_interrupt_handler_task, 0, TASK_STACK_SIZE) \
+	TASK_ALWAYS(PD_INT_C1, pd_interrupt_handler_task, 1, TASK_STACK_SIZE)
diff --git a/board/volet/gpio.inc b/board/volet/gpio.inc
new file mode 100644
index 0000000000..0b5d462b61
--- /dev/null
+++ b/board/volet/gpio.inc
@@ -0,0 +1,186 @@
+/* -*- mode:c -*-
+ *
+ * Copyright 2021 The Chromium OS Authors. All rights reserved.
+ * Use of this source code is governed by a BSD-style license that can be
+ * found in the LICENSE file.
+ */
+
+/* Declare symbolic names for all the GPIOs that we care about.
+ * Note: Those with interrupt handlers must be declared first. */
+
+/* Wake Source interrupts */
+GPIO_INT(EC_LID_OPEN,          PIN(D, 2), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, lid_interrupt)
+GPIO_INT(EC_WP_L,              PIN(A, 1), GPIO_INT_BOTH, switch_interrupt)
+GPIO_INT(H1_EC_PWR_BTN_ODL,    PIN(0, 1), GPIO_INT_BOTH, power_button_interrupt)
+GPIO_INT(ACOK_OD,              PIN(0, 0), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, extpower_interrupt)
+
+/* Power sequencing interrupts */
+GPIO_INT(SLP_S0_L,             PIN(D, 5), GPIO_INT_BOTH, power_signal_interrupt)
+#ifndef CONFIG_HOSTCMD_ESPI_VW_SLP_S3
+GPIO_INT(SLP_S3_L,             PIN(A, 5), GPIO_INT_BOTH, power_signal_interrupt)
+#endif
+GPIO_INT(SLP_SUS_L,            PIN(D, 7), GPIO_INT_BOTH, power_signal_interrupt)
+GPIO_INT(PG_EC_RSMRST_ODL,     PIN(E, 2), GPIO_INT_BOTH, power_signal_interrupt)
+GPIO_INT(PG_EC_DSW_PWROK,      PIN(C, 7), GPIO_INT_BOTH, power_signal_interrupt)
+GPIO_INT(PG_EC_ALL_SYS_PWRGD,  PIN(F, 4),  GPIO_INT_BOTH, power_signal_interrupt)
+
+/* Sensor Interrupts */
+GPIO_INT(EC_IMU_INT_L,         PIN(5, 6), GPIO_INT_FALLING | GPIO_SEL_1P8V, motion_interrupt)
+GPIO(EC_ALS_RGB_INT_L,         PIN(D, 4), GPIO_INPUT | GPIO_PULL_UP)	/* unused */
+GPIO_INT(TABLET_MODE_L,        PIN(9, 5), GPIO_INT_BOTH, gmr_tablet_switch_isr)
+/*
+ * Lid g-sensor interrupt unused on Voxel, configure as regular input for
+ * power saving.
+ */
+GPIO(EC_ACCEL_INT,		PIN(8, 1), GPIO_INPUT | GPIO_PULL_UP)
+
+/* USB-C interrupts */
+GPIO_INT(USB_C0_TCPC_INT_ODL,	PIN(E, 0), GPIO_INT_BOTH, tcpc_alert_event)
+GPIO_INT(USB_C1_TCPC_INT_ODL,	PIN(A, 2), GPIO_INT_BOTH, tcpc_alert_event)
+
+GPIO_INT(USB_C0_PPC_INT_ODL,	PIN(6, 2), GPIO_INT_BOTH, ppc_interrupt)
+GPIO_INT(USB_C1_PPC_INT_ODL,	PIN(F, 5), GPIO_INT_BOTH, ppc_interrupt)
+
+GPIO_INT(USB_C0_BC12_INT_ODL,	PIN(E, 4), GPIO_INT_BOTH, bc12_interrupt)
+GPIO_INT(USB_C1_MIX_INT_ODL,	PIN(0, 3), GPIO_INT_BOTH, bc12_interrupt)
+
+/* HDMI interrupts */
+
+/* Volume button interrupts */
+GPIO_INT(EC_VOLDN_BTN_ODL,		PIN(9, 3), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt)
+GPIO_INT(EC_VOLUP_BTN_ODL,		PIN(9, 7), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt)
+
+/* Power Sequencing Signals */
+GPIO(EN_PP3300_A,              PIN(A, 3), GPIO_OUT_LOW)
+GPIO(EN_PP5000_A,              PIN(A, 4), GPIO_OUT_LOW)
+GPIO(EN_PPVAR_VCCIN,           PIN(4, 3), GPIO_OUT_LOW) /* Enables VCCIN IMPV9 */
+GPIO(EC_PCH_DSW_PWROK,         PIN(C, 0), GPIO_OUT_LOW)
+
+/* Other wake sources */
+/*
+ * GPIO_INT_BOTH is required for PSL wake from hibernate, but we don't need an
+ * interrupt handler because it is automatically handled by the PSL.
+ *
+ * We need to lock the setting so this gpio can't be reconfigured to overdrive
+ * the real reset signal. (This is the PSL input pin not the real reset pin).
+ */
+GPIO(EC_RST_ODL,		PIN(0, 2), GPIO_INT_BOTH |
+					   GPIO_HIB_WAKE_HIGH |
+					   GPIO_LOCKED)
+
+/* AP/PCH Signals */
+GPIO(EC_PCH_SYS_PWROK,         PIN(3, 7), GPIO_OUT_LOW)
+GPIO(EC_PCH_RSMRST_ODL,        PIN(A, 6), GPIO_ODR_LOW) /* TODO - b/140950085 - implement TGL sequencing requirement */
+GPIO(EC_PCH_PWR_BTN_ODL,       PIN(C, 1), GPIO_ODR_HIGH)
+GPIO(EC_PCH_RTCRST,            PIN(7, 6), GPIO_OUT_LOW)
+GPIO(EC_PCH_WAKE_ODL,          PIN(7, 4), GPIO_ODR_HIGH)
+GPIO(EC_ENTERING_RW,           PIN(E, 3), GPIO_OUT_LOW)
+GPIO(EC_PROCHOT_ODL,           PIN(6, 3), GPIO_ODR_HIGH)
+GPIO_INT(EC_PROCHOT_IN_L,      PIN(F, 0), GPIO_INT_BOTH, throttle_ap_prochot_input_interrupt)
+GPIO(SYS_RST_ODL,              PIN(C, 5), GPIO_ODR_HIGH)
+
+GPIO(EC_PCH_INT_ODL,           PIN(B, 0), GPIO_ODR_HIGH)
+GPIO(CPU_C10_GATE_L,           PIN(6, 7), GPIO_INPUT)
+
+/* USB and USBC Signals */
+GPIO(EN_PP5000_USBA,		PIN(3, 5), GPIO_OUT_LOW)	/* Enable USB-A charging - all ports */
+GPIO(USB_A_LOW_PWR_OD,		PIN(6, 6), GPIO_ODR_LOW)	/* Don't limit USB-A charging by default - all ports */
+
+/*
+ * USB_C1 moved from GPIO32 to GPIO83 on boards with board ID >=1.
+ * GPIO83/EN_PP1800_A is DNS on board ID 0 and GPIO32 is N/C on board ID >=1
+ * so it's safe to define GPIOs compatible with both designs.
+ * TODO (b/149858568): remove board ID=0 support.
+ */
+GPIO(USB_C0_RT_RST_ODL,			PIN(4, 1), GPIO_ODR_LOW)
+GPIO(USB_C1_RT_RST_ODL,			PIN(8, 3), GPIO_ODR_LOW) /* USB_C1 Reset on boards board ID >=1 */
+GPIO(USB_C0_OC_ODL,			PIN(B, 1), GPIO_ODR_HIGH)
+GPIO(USB_C1_OC_ODL,			PIN(5, 0), GPIO_ODR_HIGH)
+GPIO(USB_C0_RT_INT_ODL,			PIN(C, 6), GPIO_INPUT)
+GPIO(USB_C1_RT_INT_ODL,			PIN(9, 6), GPIO_INPUT)
+GPIO(USB_C0_FRS_EN,			PIN(C, 2), GPIO_OUT_LOW)
+GPIO(USB_C1_FRS_EN,			PIN(9, 4), GPIO_OUT_LOW)
+
+/* Don't have a load switch for retimer */
+UNIMPLEMENTED(USB_C0_LS_EN)
+UNIMPLEMENTED(USB_C1_LS_EN)
+
+/* Misc Signals */
+GPIO(EC_H1_PACKET_MODE,		PIN(7, 5), GPIO_OUT_LOW)	/* H1 Packet Mode */
+GPIO(LED_1_L,                  PIN(C, 4), GPIO_OUT_HIGH)        /* Blue */
+GPIO(LED_2_L,                  PIN(C, 3), GPIO_OUT_HIGH)        /* Yellow */
+GPIO(EC_KB_BL_EN,		PIN(8, 6), GPIO_OUT_LOW)	/* Keyboard backlight enable*/
+
+GPIO(M2_SSD_PLN,        PIN(A, 0), GPIO_ODR_HIGH)	/* SSD power-loss notification */
+GPIO(M2_SSD_PLA,        PIN(7, 0), GPIO_INPUT)		/* SSD power-loss acknowledgment */
+GPIO(CCD_MODE_ODL,      PIN(E, 5), GPIO_INPUT)		/* Case Closed Debug Mode */
+GPIO(EC_SLP_S0IX,       PIN(7, 2), GPIO_INPUT | GPIO_PULL_UP)
+
+/* Unused signals */
+GPIO(UNUSED_GPIO34,     PIN(3, 4), GPIO_INPUT | GPIO_PULL_UP)
+GPIO(UNUSED_GPIO60,     PIN(6, 0), GPIO_INPUT | GPIO_PULL_UP)
+GPIO(UNUSED_GPIOA7,     PIN(A, 7), GPIO_INPUT | GPIO_PULL_UP)
+
+/*
+ * eDP backlight - both PCH and EC have enable pins that must be high
+ * for the backlight to turn on. Default state is high, and can be turned
+ * off during sleep states.
+ */
+GPIO(EC_EDP_BL_EN,             PIN(D, 3), GPIO_OUT_HIGH)
+
+/* I2C pins - Alternate function below configures I2C module on these pins */
+GPIO(EC_I2C0_SENSOR_SCL,       PIN(B, 5), GPIO_INPUT | GPIO_SEL_1P8V)
+GPIO(EC_I2C0_SENSOR_SDA,       PIN(B, 4), GPIO_INPUT | GPIO_SEL_1P8V)
+GPIO(EC_I2C1_USB_C0_SCL,       PIN(9, 0), GPIO_INPUT)
+GPIO(EC_I2C1_USB_C0_SDA,       PIN(8, 7), GPIO_INPUT)
+GPIO(EC_I2C2_USB_C1_SCL,       PIN(9, 2), GPIO_INPUT)
+GPIO(EC_I2C2_USB_C1_SDA,       PIN(9, 1), GPIO_INPUT)
+GPIO(EC_I2C3_USB_1_MIX_SCL,    PIN(D, 1), GPIO_INPUT)
+GPIO(EC_I2C3_USB_1_MIX_SDA,    PIN(D, 0), GPIO_INPUT)
+GPIO(EC_I2C4_USB_1_MIX_SCL,    PIN(F, 3), GPIO_INPUT)
+GPIO(EC_I2C4_USB_1_MIX_SDA,    PIN(F, 2), GPIO_INPUT)
+GPIO(EC_I2C5_POWER_SCL,        PIN(3, 3), GPIO_INPUT)
+GPIO(EC_I2C5_POWER_SDA,        PIN(3, 6), GPIO_INPUT)
+GPIO(EC_I2C7_EEPROM_SCL,       PIN(B, 3), GPIO_INPUT)
+GPIO(EC_I2C7_EEPROM_SDA,       PIN(B, 2), GPIO_INPUT)
+
+/* Battery signals */
+GPIO(EC_BATT_PRES_ODL, 		PIN(E, 1), GPIO_INPUT)
+
+/* Alternate functions GPIO definitions */
+ALTERNATE(PIN_MASK(B, BIT(5) | BIT(4)), 0, MODULE_I2C, (GPIO_INPUT | GPIO_SEL_1P8V)) /* I2C0 */
+ALTERNATE(PIN_MASK(9, BIT(0) | BIT(2) | BIT(1)), 0, MODULE_I2C, 0)                   /* I2C1 SCL / I2C2 */
+ALTERNATE(PIN_MASK(8, BIT(7)), 0, MODULE_I2C, 0)                                     /* I2C1 SDA */
+ALTERNATE(PIN_MASK(D, BIT(1) | BIT(0)), 0, MODULE_I2C, 0)                            /* I2C3 */
+ALTERNATE(PIN_MASK(F, BIT(3) | BIT(2)), 0, MODULE_I2C, 0)                            /* I2C4 */
+ALTERNATE(PIN_MASK(3, BIT(3) | BIT(6)), 0, MODULE_I2C, 0)                            /* I2C5 */
+ALTERNATE(PIN_MASK(B, BIT(3) | BIT(2)), 0, MODULE_I2C, 0)                            /* I2C7 */
+
+/* Fan signals */
+GPIO(EN_PP5000_FAN,            PIN(6, 1), GPIO_OUT_LOW)
+ALTERNATE(PIN_MASK(B, BIT(7)), 0, MODULE_PWM, 0)	/* FAN_PWM */
+ALTERNATE(PIN_MASK(4, BIT(0)), 0, MODULE_PWM, 0)	/* FAN_SPEED_TACH */
+
+/* Keyboard pins */
+#define GPIO_KB_INPUT (GPIO_INPUT | GPIO_PULL_UP)
+ALTERNATE(PIN_MASK(3, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_KB_INPUT) /* KSI_00-01 */
+ALTERNATE(PIN_MASK(2, 0xFC), 0, MODULE_KEYBOARD_SCAN, GPIO_KB_INPUT) /* KSI_02-07 */
+ALTERNATE(PIN_MASK(2, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_00-01 */
+GPIO(EC_KSO_02_INV, PIN(1, 7),                        GPIO_OUT_LOW)  /* KSO_02 */
+ALTERNATE(PIN_MASK(1, 0x7F), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_03-09 */
+ALTERNATE(PIN_MASK(0, 0xF0), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_10-13 */
+ALTERNATE(PIN_MASK(8, 0x04), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_14 */
+ALTERNATE(PIN_MASK(8, BIT(0)), 0, MODULE_PWM, 0)                     /* EC_KB_BL_PWM */
+
+/* UART */
+ALTERNATE(PIN_MASK(6, BIT(5) | BIT(4)), 0, MODULE_UART, 0)                           /* UART from EC to Servo */
+
+/* Power Switch Logic (PSL) inputs */
+ALTERNATE(PIN_MASK(D, BIT(2)), 0, MODULE_PMU, 0)                    /* GPIOD2 = EC_LID_OPEN */
+ALTERNATE(PIN_MASK(0, BIT(0) | BIT(1) | BIT(2)), 0, MODULE_PMU, 0)  /* GPIO00 = ACOK_OD,
+                                                                       GPIO01 = H1_EC_PWR_BTN_ODL
+                                                                       GPIO02 = EC_RST_ODL */
+
+/* Temperature sensors */
+ALTERNATE(PIN_MASK(4, BIT(2) | BIT(4) | BIT(5)), 0, MODULE_ADC, 0) /* TEMP_SENSOR1,2,4 */
+ALTERNATE(PIN(F, 1), 0, MODULE_ADC, 0) /* TEMP_SENSOR3 */
diff --git a/board/volet/led.c b/board/volet/led.c
new file mode 100644
index 0000000000..ba4af36163
--- /dev/null
+++ b/board/volet/led.c
@@ -0,0 +1,79 @@
+/* Copyright 2021 The Chromium OS Authors. All rights reserved.
+ * Use of this source code is governed by a BSD-style license that can be
+ * found in the LICENSE file.
+ *
+ * Power and battery LED control for Volteer
+ */
+
+#include "ec_commands.h"
+#include "gpio.h"
+#include "led_common.h"
+#include "led_onoff_states.h"
+#include "chipset.h"
+
+#define LED_ON_LVL 0
+#define LED_OFF_LVL 1
+
+__override const int led_charge_lvl_1 = 5;
+
+__override const int led_charge_lvl_2 = 95;
+
+__override struct led_descriptor
+			led_bat_state_table[LED_NUM_STATES][LED_NUM_PHASES] = {
+	[STATE_CHARGING_LVL_1]	     = {{EC_LED_COLOR_AMBER, LED_INDEFINITE} },
+	[STATE_CHARGING_LVL_2]	     = {{EC_LED_COLOR_AMBER, LED_INDEFINITE} },
+	[STATE_CHARGING_FULL_CHARGE] = {{EC_LED_COLOR_BLUE,  LED_INDEFINITE} },
+	[STATE_DISCHARGE_S0]	     = {{EC_LED_COLOR_BLUE,  LED_INDEFINITE} },
+	[STATE_DISCHARGE_S3]	     = {{EC_LED_COLOR_AMBER, 1 * LED_ONE_SEC},
+					{LED_OFF,            3 * LED_ONE_SEC} },
+	[STATE_DISCHARGE_S5]         = {{LED_OFF,  LED_INDEFINITE} },
+	[STATE_BATTERY_ERROR]        = {{EC_LED_COLOR_AMBER,  1 * LED_ONE_SEC},
+					{LED_OFF,	    1 * LED_ONE_SEC} },
+	[STATE_FACTORY_TEST]         = {{EC_LED_COLOR_BLUE,   2 * LED_ONE_SEC},
+					{EC_LED_COLOR_AMBER, 2 * LED_ONE_SEC} },
+};
+
+const enum ec_led_id supported_led_ids[] = {
+	EC_LED_ID_BATTERY_LED
+};
+
+const int supported_led_ids_count = ARRAY_SIZE(supported_led_ids);
+
+__override void led_set_color_battery(enum ec_led_colors color)
+{
+	switch (color) {
+	case EC_LED_COLOR_AMBER:
+		gpio_set_level(GPIO_LED_2_L, LED_ON_LVL);
+		gpio_set_level(GPIO_LED_1_L, LED_OFF_LVL);
+		break;
+	case EC_LED_COLOR_BLUE:
+		gpio_set_level(GPIO_LED_1_L, LED_ON_LVL);
+		gpio_set_level(GPIO_LED_2_L, LED_OFF_LVL);
+		break;
+	default: /* LED_OFF and other unsupported colors */
+		gpio_set_level(GPIO_LED_1_L, LED_OFF_LVL);
+		gpio_set_level(GPIO_LED_2_L, LED_OFF_LVL);
+		break;
+	}
+}
+
+void led_get_brightness_range(enum ec_led_id led_id, uint8_t *brightness_range)
+{
+	if (led_id == EC_LED_ID_BATTERY_LED) {
+		brightness_range[EC_LED_COLOR_AMBER] = 1;
+		brightness_range[EC_LED_COLOR_BLUE] = 1;
+	}
+}
+
+int led_set_brightness(enum ec_led_id led_id, const uint8_t *brightness)
+{
+	if (led_id == EC_LED_ID_BATTERY_LED) {
+		if (brightness[EC_LED_COLOR_BLUE] != 0)
+			led_set_color_battery(EC_LED_COLOR_BLUE);
+		else if (brightness[EC_LED_COLOR_AMBER] != 0)
+			led_set_color_battery(EC_LED_COLOR_AMBER);
+		else
+			led_set_color_battery(LED_OFF);
+	}
+	return EC_SUCCESS;
+}
diff --git a/board/volet/sensors.c b/board/volet/sensors.c
new file mode 100644
index 0000000000..7185a9d65d
--- /dev/null
+++ b/board/volet/sensors.c
@@ -0,0 +1,266 @@
+/* Copyright 2021 The Chromium OS Authors. All rights reserved.
+ * Use of this source code is governed by a BSD-style license that can be
+ * found in the LICENSE file.
+ */
+
+/* Volteer family-specific sensor configuration */
+#include "common.h"
+#include "accelgyro.h"
+#include "cbi_ec_fw_config.h"
+#include "cbi_ssfc.h"
+#include "driver/accel_bma2x2.h"
+#include "driver/accel_kionix.h"
+#include "driver/accelgyro_bmi_common.h"
+#include "driver/accelgyro_bmi160.h"
+#include "driver/accelgyro_icm_common.h"
+#include "driver/accelgyro_icm426xx.h"
+#include "driver/als_tcs3400.h"
+#include "driver/sync.h"
+#include "keyboard_scan.h"
+#include "hooks.h"
+#include "i2c.h"
+#include "task.h"
+#include "tablet_mode.h"
+#include "util.h"
+
+#define CPRINTS(format, args...) cprints(CC_MOTION_SENSE, format, ## args)
+/******************************************************************************/
+/* Sensors */
+static struct mutex g_lid_accel_mutex;
+static struct mutex g_base_mutex;
+
+/* BMA253 private data */
+static struct accelgyro_saved_data_t g_bma253_data;
+static struct kionix_accel_data g_kx022_data;
+
+/* BMI160 private data */
+static struct bmi_drv_data_t g_bmi160_data;
+static struct icm_drv_data_t g_icm426xx_data;
+
+/* Rotation matrix for the lid accelerometer */
+static const mat33_fp_t lid_standard_ref = {
+	{ FLOAT_TO_FP(-1), 0, 0},
+	{ 0, FLOAT_TO_FP(-1), 0},
+	{ 0, 0, FLOAT_TO_FP(1)}
+};
+
+const mat33_fp_t base_standard_ref = {
+	{ 0, FLOAT_TO_FP(1), 0},
+	{ FLOAT_TO_FP(-1), 0, 0},
+	{ 0, 0, FLOAT_TO_FP(1)}
+};
+
+static const mat33_fp_t base_icm_ref = {
+	{ FLOAT_TO_FP(1), 0, 0},
+	{ 0, FLOAT_TO_FP(1), 0},
+	{ 0, 0, FLOAT_TO_FP(1)}
+};
+
+struct motion_sensor_t kx022_lid_accel = {
+	.name = "Lid Accel",
+	.active_mask = SENSOR_ACTIVE_S0_S3,
+	.chip = MOTIONSENSE_CHIP_KX022,
+	.type = MOTIONSENSE_TYPE_ACCEL,
+	.location = MOTIONSENSE_LOC_LID,
+	.drv = &kionix_accel_drv,
+	.mutex = &g_lid_accel_mutex,
+	.drv_data = &g_kx022_data,
+	.port = I2C_PORT_ACCEL,
+	.i2c_spi_addr_flags = KX022_ADDR0_FLAGS,
+	.rot_standard_ref = &lid_standard_ref,
+	.min_frequency = KX022_ACCEL_MIN_FREQ,
+	.max_frequency = KX022_ACCEL_MAX_FREQ,
+	.default_range = 2, /* g, to support tablet mode */
+	.config = {
+		/* EC use accel for angle detection */
+		[SENSOR_CONFIG_EC_S0] = {
+			.odr = 10000 | ROUND_UP_FLAG,
+		},
+		/* EC use accel for angle detection */
+		[SENSOR_CONFIG_EC_S3] = {
+			.odr = 10000 | ROUND_UP_FLAG,
+		},
+	},
+};
+
+struct motion_sensor_t icm426xx_base_accel = {
+	.name = "Base Accel",
+	.active_mask = SENSOR_ACTIVE_S0_S3,
+	.chip = MOTIONSENSE_CHIP_ICM426XX,
+	.type = MOTIONSENSE_TYPE_ACCEL,
+	.location = MOTIONSENSE_LOC_BASE,
+	.drv = &icm426xx_drv,
+	.mutex = &g_base_mutex,
+	.drv_data = &g_icm426xx_data,
+	.port = I2C_PORT_ACCEL,
+	.i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS,
+	.default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs.*/
+	.rot_standard_ref = &base_icm_ref,
+	.min_frequency = ICM426XX_ACCEL_MIN_FREQ,
+	.max_frequency = ICM426XX_ACCEL_MAX_FREQ,
+	.config = {
+		/* EC use accel for angle detection */
+		[SENSOR_CONFIG_EC_S0] = {
+			.odr = 10000 | ROUND_UP_FLAG,
+			.ec_rate = 100 * MSEC,
+		},
+		/* EC use accel for angle detection */
+		[SENSOR_CONFIG_EC_S3] = {
+			.odr = 10000 | ROUND_UP_FLAG,
+			.ec_rate = 100 * MSEC,
+		},
+	},
+};
+
+struct motion_sensor_t icm426xx_base_gyro = {
+	.name = "Base Gyro",
+	.active_mask = SENSOR_ACTIVE_S0_S3,
+	.chip = MOTIONSENSE_CHIP_ICM426XX,
+	.type = MOTIONSENSE_TYPE_GYRO,
+	.location = MOTIONSENSE_LOC_BASE,
+	.drv = &icm426xx_drv,
+	.mutex = &g_base_mutex,
+	.drv_data = &g_icm426xx_data,
+	.port = I2C_PORT_ACCEL,
+	.i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS,
+	.default_range = 1000, /* dps */
+	.rot_standard_ref = &base_icm_ref,
+	.min_frequency = ICM426XX_GYRO_MIN_FREQ,
+	.max_frequency = ICM426XX_GYRO_MAX_FREQ,
+};
+
+struct motion_sensor_t motion_sensors[] = {
+	[LID_ACCEL] = {
+		.name = "Lid Accel",
+		.active_mask = SENSOR_ACTIVE_S0_S3,
+		.chip = MOTIONSENSE_CHIP_BMA255,
+		.type = MOTIONSENSE_TYPE_ACCEL,
+		.location = MOTIONSENSE_LOC_LID,
+		.drv = &bma2x2_accel_drv,
+		.mutex = &g_lid_accel_mutex,
+		.drv_data = &g_bma253_data,
+		.port = I2C_PORT_SENSOR,
+		.i2c_spi_addr_flags = BMA2x2_I2C_ADDR1_FLAGS,
+		.rot_standard_ref = &lid_standard_ref,
+		.min_frequency = BMA255_ACCEL_MIN_FREQ,
+		.max_frequency = BMA255_ACCEL_MAX_FREQ,
+		.default_range = 2, /* g, to support tablet mode */
+		.config = {
+			/* EC use accel for angle detection */
+			[SENSOR_CONFIG_EC_S0] = {
+				.odr = 10000 | ROUND_UP_FLAG,
+			},
+			/* Sensor on in S3 */
+			[SENSOR_CONFIG_EC_S3] = {
+				.odr = 10000 | ROUND_UP_FLAG,
+			},
+		},
+	},
+	[BASE_ACCEL] = {
+		.name = "Base Accel",
+		.active_mask = SENSOR_ACTIVE_S0_S3,
+		.chip = MOTIONSENSE_CHIP_BMI160,
+		.type = MOTIONSENSE_TYPE_ACCEL,
+		.location = MOTIONSENSE_LOC_BASE,
+		.drv = &bmi160_drv,
+		.mutex = &g_base_mutex,
+		.drv_data = &g_bmi160_data,
+		.port = I2C_PORT_SENSOR,
+		.i2c_spi_addr_flags = BMI160_ADDR0_FLAGS,
+		.rot_standard_ref = &base_standard_ref,
+		.min_frequency = BMI_ACCEL_MIN_FREQ,
+		.max_frequency = BMI_ACCEL_MAX_FREQ,
+		.default_range = 4, /* g */
+		.config = {
+			/* EC use accel for angle detection */
+			[SENSOR_CONFIG_EC_S0] = {
+				.odr = 10000 | ROUND_UP_FLAG,
+				.ec_rate = 100 * MSEC,
+			},
+			/* Sensor on in S3 */
+			[SENSOR_CONFIG_EC_S3] = {
+				.odr = 10000 | ROUND_UP_FLAG,
+				.ec_rate = 100 * MSEC,
+			},
+		},
+	},
+
+	[BASE_GYRO] = {
+		.name = "Base Gyro",
+		.active_mask = SENSOR_ACTIVE_S0_S3,
+		.chip = MOTIONSENSE_CHIP_BMI160,
+		.type = MOTIONSENSE_TYPE_GYRO,
+		.location = MOTIONSENSE_LOC_BASE,
+		.drv = &bmi160_drv,
+		.mutex = &g_base_mutex,
+		.drv_data = &g_bmi160_data,
+		.port = I2C_PORT_SENSOR,
+		.i2c_spi_addr_flags = BMI160_ADDR0_FLAGS,
+		.default_range = 1000, /* dps */
+		.rot_standard_ref = &base_standard_ref,
+		.min_frequency = BMI_GYRO_MIN_FREQ,
+		.max_frequency = BMI_GYRO_MAX_FREQ,
+	},
+};
+unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors);
+
+static void board_sensors_init(void)
+{
+	if (ec_cfg_has_tabletmode()) {
+		if (get_cbi_ssfc_base_sensor() == SSFC_SENSOR_BASE_ICM426XX) {
+			motion_sensors[BASE_ACCEL] = icm426xx_base_accel;
+			motion_sensors[BASE_GYRO] = icm426xx_base_gyro;
+			ccprints("BASE GYRO is ICM426XX");
+		} else
+			ccprints("BASE GYRO is BMI160");
+
+		if (get_cbi_ssfc_lid_sensor() == SSFC_SENSOR_LID_KX022) {
+			motion_sensors[LID_ACCEL] = kx022_lid_accel;
+			ccprints("LID_ACCEL is KX022");
+		} else
+			ccprints("LID_ACCEL is BMA253");
+
+		motion_sensor_count = ARRAY_SIZE(motion_sensors);
+		/* Enable interrupt for the accel/gyro sensor */
+		gpio_enable_interrupt(GPIO_EC_IMU_INT_L);
+	} else {
+		motion_sensor_count = 0;
+		gmr_tablet_switch_disable();
+		/* Base accel is not stuffed, don't allow line to float */
+		gpio_set_flags(GPIO_EC_IMU_INT_L,
+			       GPIO_INPUT | GPIO_PULL_DOWN);
+	}
+}
+DECLARE_HOOK(HOOK_INIT, board_sensors_init, HOOK_PRIO_DEFAULT);
+
+void motion_interrupt(enum gpio_signal signal)
+{
+	switch (get_cbi_ssfc_base_sensor()) {
+	case SSFC_SENSOR_BASE_ICM426XX:
+		icm426xx_interrupt(signal);
+		break;
+	case SSFC_SENSOR_BASE_BMI160:
+	default:
+		bmi160_interrupt(signal);
+		break;
+	}
+}
+
+#ifndef TEST_BUILD
+void lid_angle_peripheral_enable(int enable)
+{
+	int chipset_in_s0 = chipset_in_state(CHIPSET_STATE_ON);
+
+	if (enable) {
+		keyboard_scan_enable(1, KB_SCAN_DISABLE_LID_ANGLE);
+	} else {
+		/*
+		 * Ensure that the chipset is off before disabling the keyboard.
+		 * When the chipset is on, the EC keeps the keyboard enabled and
+		 * the AP decides whether to ignore input devices or not.
+		 */
+		if (!chipset_in_s0)
+			keyboard_scan_enable(0, KB_SCAN_DISABLE_LID_ANGLE);
+	}
+}
+#endif
diff --git a/board/volet/vif_override.xml b/board/volet/vif_override.xml
new file mode 100644
index 0000000000..3fc41630da
--- /dev/null
+++ b/board/volet/vif_override.xml
@@ -0,0 +1,158 @@
+<?xml version="1.0" encoding="utf-8"?>
+<VIF xmlns="http://usb.org/VendorInfoFile.xsd">
+  <Model_Part_Number>Voxel</Model_Part_Number>
+  <Product_Revision>0</Product_Revision>
+  <TID>0</TID>
+  <Product>
+    <!-- Information about TGL USB4 provided by Intel. See b/172963736 -->
+    <USB4_Num_Internal_Host_Controllers value="1" />
+    <USB4_Num_PCIe_DN_Bridges value="0" />
+    <USB4RouterList>
+      <Usb4Router>
+        <USB4_Router_ID value="1" />
+        <USB4_Silicon_VID value="32903">8087</USB4_Silicon_VID>
+        <USB4_Num_Lane_Adapters value="4" />
+        <USB4_Num_USB3_DN_Adapters value="1" />
+        <USB4_Num_DP_IN_Adapters value="1" />
+        <USB4_Num_DP_OUT_Adapters value="0" />
+        <USB4_Num_PCIe_DN_Adapters value="4" />
+        <USB4_TBT3_Not_Supported value="0">TBT3 Compatible</USB4_TBT3_Not_Supported>
+        <USB4_PCIe_Wake_Supported value="true" />
+        <USB4_USB3_Wake_Supported value="false" />
+        <USB4_Num_Unused_Adapters value="0" />
+        <USB4_TBT3_VID value="32903">8087</USB4_TBT3_VID>
+        <USB4_PCIe_Switch_Vendor_ID value="32902">8086</USB4_PCIe_Switch_Vendor_ID>
+        <USB4_PCIe_Switch_Device_ID value="39451">9A1B</USB4_PCIe_Switch_Device_ID>
+      </Usb4Router>
+      <Usb4Router>
+        <USB4_Router_ID value="0" />
+        <USB4_Silicon_VID value="32903">8087</USB4_Silicon_VID>
+        <USB4_Num_Lane_Adapters value="2" />
+        <USB4_Num_USB3_DN_Adapters value="1" />
+        <USB4_Num_DP_IN_Adapters value="0" />
+        <USB4_Num_DP_OUT_Adapters value="0" />
+        <USB4_Num_PCIe_DN_Adapters value="0" />
+        <USB4_TBT3_Not_Supported value="1">Not TBT3-Compatible</USB4_TBT3_Not_Supported>
+        <USB4_PCIe_Wake_Supported value="false" />
+        <USB4_USB3_Wake_Supported value="false" />
+        <USB4_Num_Unused_Adapters value="0" />
+      </Usb4Router>
+    </USB4RouterList>
+  </Product>
+  <Component>
+    <USB4_Max_Speed value="1">Gen 3 (40Gb)</USB4_Max_Speed>
+    <USB4_DFP_Supported value="true" />
+    <USB4_UFP_Supported value="false" />
+    <USB4_USB3_Tunneling_Supported value="true" />
+    <USB4_DP_Tunneling_Supported value="true" />
+    <USB4_PCIe_Tunneling_Supported value="true" />
+    <USB4_TBT3_Compatibility_Supported value="true" />
+    <USB4_CL1_State_Supported value="true" />
+    <USB4_CL2_State_Supported value="true" />
+    <USB4_Num_Retimers value="1" />
+    <USB4_DP_Bit_Rate value="3">HBR3</USB4_DP_Bit_Rate>
+    <USB4_Num_DP_Lanes value="4">4 Lanes</USB4_Num_DP_Lanes>
+    <USB4_Lane_0_Adapter value="1" />
+    <Host_Supports_USB_Data value="true" />
+    <Host_Speed value="2">USB 3.2 Gen 2x1</Host_Speed>
+    <Host_Contains_Captive_Retimer value="true" />
+    <Host_Truncates_DP_For_tDHPResponse value="false" />
+    <Host_Suspend_Supported value="true" />
+    <Is_DFP_On_Hub value="false" />
+    <USB_Suspend_May_Be_Cleared value="true" />
+    <FR_Swap_Type_C_Current_Capability_As_Initial_Sink value="3">3A @ 5V</FR_Swap_Type_C_Current_Capability_As_Initial_Sink>
+    <FR_Swap_Supported_As_Initial_Sink value="true" />
+    <SrcPdoList>
+      <SrcPDO>
+        <!-- Add in missing fields for SrcPdo0, derived from SYV682B datasheet. -->
+        <Src_PD_OCP_OC_Debounce value="50">50 msec</Src_PD_OCP_OC_Debounce>
+        <Src_PD_OCP_OC_Threshold value="360">3600 mA</Src_PD_OCP_OC_Threshold>
+      </SrcPDO>
+    </SrcPdoList>
+    <Data_Capable_As_USB_Host_SOP value="true" />
+    <Data_Capable_As_USB_Device_SOP value="false" />
+    <!-- TODO(b/173028252): Figure out the appropriate Discover Identity ACK for
+         Volteer and update the EC and VIF accordingly. -->
+    <Product_Type_UFP_SOP value="3">PSD</Product_Type_UFP_SOP>
+    <Product_Type_DFP_SOP value="4">Alternate Mode Controller (AMC)</Product_Type_DFP_SOP>
+    <DFP_VDO_Port_Number value="0" />
+    <Modal_Operation_Supported_SOP value="true" />
+    <USB_VID_SOP value="6353">18D1</USB_VID_SOP>
+    <bcdDevice_SOP value="0">0000</bcdDevice_SOP>
+    <SVID_Fixed_SOP value="true" />
+    <Num_SVIDs_Min_SOP value="1" />
+    <Num_SVIDs_Max_SOP value="1" />
+    <SOPSVIDList>
+      <SOPSVID>
+        <SVID_SOP value="32903">8087</SVID_SOP>
+        <SVID_Modes_Fixed_SOP value="true" />
+        <SVID_Num_Modes_Min_SOP value="1" />
+        <SVID_Num_Modes_Max_SOP value="1" />
+        <SOPSVIDModeList>
+          <SOPSVIDMode>
+            <SVID_Mode_Enter_SOP value="true" />
+            <SVID_Mode_Recog_Value_SOP value="0">00000000</SVID_Mode_Recog_Value_SOP>
+          </SOPSVIDMode>
+        </SOPSVIDModeList>
+      </SOPSVID>
+    </SOPSVIDList>
+  </Component>
+  <Component>
+    <USB4_Max_Speed value="1">Gen 3 (40Gb)</USB4_Max_Speed>
+    <USB4_DFP_Supported value="true" />
+    <USB4_UFP_Supported value="false" />
+    <USB4_USB3_Tunneling_Supported value="true" />
+    <USB4_DP_Tunneling_Supported value="true" />
+    <USB4_PCIe_Tunneling_Supported value="true" />
+    <USB4_TBT3_Compatibility_Supported value="true" />
+    <USB4_CL1_State_Supported value="true" />
+    <USB4_CL2_State_Supported value="true" />
+    <USB4_Num_Retimers value="1" />
+    <USB4_DP_Bit_Rate value="3">HBR3</USB4_DP_Bit_Rate>
+    <USB4_Num_DP_Lanes value="4">4 Lanes</USB4_Num_DP_Lanes>
+    <USB4_Lane_0_Adapter value="1" />
+    <Host_Supports_USB_Data value="true" />
+    <Host_Speed value="2">USB 3.2 Gen 2x1</Host_Speed>
+    <Host_Contains_Captive_Retimer value="true" />
+    <Host_Truncates_DP_For_tDHPResponse value="false" />
+    <Host_Suspend_Supported value="true" />
+    <Is_DFP_On_Hub value="false" />
+    <USB_Suspend_May_Be_Cleared value="true" />
+    <FR_Swap_Type_C_Current_Capability_As_Initial_Sink value="3">3A @ 5V</FR_Swap_Type_C_Current_Capability_As_Initial_Sink>
+    <FR_Swap_Supported_As_Initial_Sink value="true" />
+    <SrcPdoList>
+      <SrcPDO>
+        <!-- Add in missing fields for SrcPdo0, derived from SYV682B datasheet. -->
+        <Src_PD_OCP_OC_Debounce value="50">50 msec</Src_PD_OCP_OC_Debounce>
+        <Src_PD_OCP_OC_Threshold value="360">3600 mA</Src_PD_OCP_OC_Threshold>
+      </SrcPDO>
+    </SrcPdoList>
+    <Data_Capable_As_USB_Host_SOP value="true" />
+    <Data_Capable_As_USB_Device_SOP value="false" />
+    <!-- TODO(b/173028252): Figure out the appropriate Discover Identity ACK for
+         Volteer and update the EC and VIF accordingly. -->
+    <Product_Type_UFP_SOP value="3">PSD</Product_Type_UFP_SOP>
+    <Product_Type_DFP_SOP value="4">Alternate Mode Controller (AMC)</Product_Type_DFP_SOP>
+    <DFP_VDO_Port_Number value="1" />
+    <Modal_Operation_Supported_SOP value="true" />
+    <USB_VID_SOP value="6353">18D1</USB_VID_SOP>
+    <bcdDevice_SOP value="0">0000</bcdDevice_SOP>
+    <SVID_Fixed_SOP value="true" />
+    <Num_SVIDs_Min_SOP value="1" />
+    <Num_SVIDs_Max_SOP value="1" />
+    <SOPSVIDList>
+      <SOPSVID>
+        <SVID_SOP value="32903">8087</SVID_SOP>
+        <SVID_Modes_Fixed_SOP value="true" />
+        <SVID_Num_Modes_Min_SOP value="1" />
+        <SVID_Num_Modes_Max_SOP value="1" />
+        <SOPSVIDModeList>
+          <SOPSVIDMode>
+            <SVID_Mode_Enter_SOP value="true" />
+            <SVID_Mode_Recog_Value_SOP value="0">00000000</SVID_Mode_Recog_Value_SOP>
+          </SOPSVIDMode>
+        </SOPSVIDModeList>
+      </SOPSVID>
+    </SOPSVIDList>
+  </Component>
+</VIF>