brask: remove unnecessary configuration

This patch removes the configuration for the battery, charger,
fan control, board id, keyboard, keyboard backlight, sensor,
hibernate and led.
In order to make the build pass, the CONFIG_ADC,
CONFIG_POWER_BUTTON_IGNORE_LID and CONFIG_POWER_BUTTON_INIT_IDLE
are added to the board.h/baseboard.h. In additional, the
function board_set_active_charge_port() and board_set_charge_limit()
are added to the board.c to avoid build error.

BUG=b:191637086
BRANCH=None
TEST=make BOARD=brask

Change-Id: I15c01820dbd2f58f5722c87de51ebf425ffca13a
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/3114497
Reviewed-by: Boris Mittelberg <bmbm@google.com>
Reviewed-by: caveh jalali <caveh@chromium.org>

14 files changed, 35 insertions, 963 deletions

diff --git a/board/brask/battery.c b/board/brask/battery.c
deleted file mode 100644
index a18ab029b6..0000000000
--- a/board/brask/battery.c
+++ /dev/null
@@ -1,98 +0,0 @@
-/* Copyright 2021 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- *
- * Battery pack vendor provided charging profile
- */
-
-#include "battery_fuel_gauge.h"
-#include "common.h"
-#include "compile_time_macros.h"
-
-/*
- * Battery info for all Brya battery types. Note that the fields
- * start_charging_min/max and charging_min/max are not used for the charger.
- * The effective temperature limits are given by discharging_min/max_c.
- *
- * Fuel Gauge (FG) parameters which are used for determining if the battery
- * is connected, the appropriate ship mode (battery cutoff) command, and the
- * charge/discharge FETs status.
- *
- * Ship mode (battery cutoff) requires 2 writes to the appropriate smart battery
- * register. For some batteries, the charge/discharge FET bits are set when
- * charging/discharging is active, in other types, these bits set mean that
- * charging/discharging is disabled. Therefore, in addition to the mask for
- * these bits, a disconnect value must be specified. Note that for TI fuel
- * gauge, the charge/discharge FET status is found in Operation Status (0x54),
- * but a read of Manufacturer Access (0x00) will return the lower 16 bits of
- * Operation status which contains the FET status bits.
- *
- * The assumption for battery types supported is that the charge/discharge FET
- * status can be read with a sb_read() command and therefore, only the register
- * address, mask, and disconnect value need to be provided.
- */
-const struct board_batt_params board_battery_info[] = {
-	/* POW-TECH GQA05 Battery Information */
-	[BATTERY_POWER_TECH] = {
-		/* BQ40Z50 Fuel Gauge */
-		.fuel_gauge = {
-			.manuf_name = "POW-TECH",
-			.device_name = "BATGQA05L22",
-			.ship_mode = {
-				.reg_addr = 0x00,
-				.reg_data = { 0x0010, 0x0010 },
-			},
-			.fet = {
-				.mfgacc_support = 1,
-				.reg_addr = 0x00,
-				.reg_mask = 0x2000,		/* XDSG */
-				.disconnect_val = 0x2000,
-			}
-		},
-		.batt_info = {
-			.voltage_max		= TARGET_WITH_MARGIN(13050, 5),
-			.voltage_normal		= 11400, /* mV */
-			.voltage_min		= 9000, /* mV */
-			.precharge_current	= 280,	/* mA */
-			.start_charging_min_c	= 0,
-			.start_charging_max_c	= 45,
-			.charging_min_c		= 0,
-			.charging_max_c		= 45,
-			.discharging_min_c	= -10,
-			.discharging_max_c	= 60,
-		},
-	},
-	/* LGC L17L3PB0 Battery Information */
-	/*
-	 * Battery info provided by ODM on b/143477210, comment #11
-	 */
-	[BATTERY_LGC011] = {
-		.fuel_gauge = {
-			.manuf_name = "LGC",
-			.ship_mode = {
-				.reg_addr = 0x00,
-				.reg_data = { 0x0010, 0x0010 },
-			},
-			.fet = {
-				.reg_addr = 0x0,
-				.reg_mask = 0x6000,
-				.disconnect_val = 0x6000,
-			}
-		},
-		.batt_info = {
-			.voltage_max		= TARGET_WITH_MARGIN(13200, 5),
-			.voltage_normal		= 11550, /* mV */
-			.voltage_min		= 9000, /* mV */
-			.precharge_current	= 256,	/* mA */
-			.start_charging_min_c	= 0,
-			.start_charging_max_c	= 45,
-			.charging_min_c		= 0,
-			.charging_max_c		= 60,
-			.discharging_min_c	= 0,
-			.discharging_max_c	= 75,
-		},
-	},
-};
-BUILD_ASSERT(ARRAY_SIZE(board_battery_info) == BATTERY_TYPE_COUNT);
-
-const enum battery_type DEFAULT_BATTERY_TYPE = BATTERY_POWER_TECH;
diff --git a/board/brask/board.c b/board/brask/board.c
index 1935988607..53eeed42d7 100644
--- a/board/brask/board.c
+++ b/board/brask/board.c
@@ -1,29 +1,16 @@
-/* Copyright 2020 The Chromium OS Authors. All rights reserved.
+/* Copyright 2021 The Chromium OS Authors. All rights reserved.
  * Use of this source code is governed by a BSD-style license that can be
  * found in the LICENSE file.
  */
 
-#include "battery.h"
-#include "button.h"
-#include "charge_ramp.h"
-#include "charger.h"
 #include "common.h"
 #include "compile_time_macros.h"
 #include "console.h"
 #include "gpio.h"
 #include "gpio_signal.h"
-#include "hooks.h"
-#include "driver/accel_lis2dw12.h"
-#include "driver/accelgyro_lsm6dso.h"
-#include "driver/als_tcs3400.h"
-#include "fw_config.h"
-#include "hooks.h"
-#include "lid_switch.h"
 #include "power_button.h"
 #include "power.h"
-#include "registers.h"
 #include "switch.h"
-#include "tablet_mode.h"
 #include "throttle_ap.h"
 #include "usbc_config.h"
 
@@ -48,118 +35,13 @@ __override void board_cbi_init(void)
 	config_usb_db_type();
 }
 
-/* Called on AP S3 -> S0 transition */
-static void board_chipset_resume(void)
+int board_set_active_charge_port(int port)
 {
-	/* Allow keyboard backlight to be enabled */
-
-	if (get_board_id() == 1)
-		gpio_set_level(GPIO_ID_1_EC_KB_BL_EN, 1);
-	else
-		gpio_set_level(GPIO_EC_KB_BL_EN_L, 0);
+	/* TODO(b/197514362): set either barreljack or typec port */
+	return EC_SUCCESS;
 }
-DECLARE_HOOK(HOOK_CHIPSET_RESUME, board_chipset_resume, HOOK_PRIO_DEFAULT);
 
-/* Called on AP S0 -> S3 transition */
-static void board_chipset_suspend(void)
+void board_set_charge_limit(int port, int supplier, int charge_ma,
+				int max_ma, int charge_mv)
 {
-	/* Turn off the keyboard backlight if it's on. */
-
-	if (get_board_id() == 1)
-		gpio_set_level(GPIO_ID_1_EC_KB_BL_EN, 0);
-	else
-		gpio_set_level(GPIO_EC_KB_BL_EN_L, 1);
-}
-DECLARE_HOOK(HOOK_CHIPSET_SUSPEND, board_chipset_suspend, HOOK_PRIO_DEFAULT);
-
-#ifdef CONFIG_CHARGE_RAMP_SW
-
-/*
- * TODO(b/181508008): tune this threshold
- */
-
-#define BC12_MIN_VOLTAGE 4400
-
-/**
- * Return true if VBUS is too low
- */
-int board_is_vbus_too_low(int port, enum chg_ramp_vbus_state ramp_state)
-{
-	int voltage;
-
-	if (charger_get_vbus_voltage(port, &voltage))
-		voltage = 0;
-
-	if (voltage == 0) {
-		CPRINTS("%s: must be disconnected", __func__);
-		return 1;
-	}
-
-	if (voltage < BC12_MIN_VOLTAGE) {
-		CPRINTS("%s: port %d: vbus %d lower than %d", __func__,
-			port, voltage, BC12_MIN_VOLTAGE);
-		return 1;
-	}
-
-	return 0;
-}
-
-#endif /* CONFIG_CHARGE_RAMP_SW */
-
-enum battery_present battery_hw_present(void)
-{
-	enum gpio_signal batt_pres;
-
-	if (get_board_id() == 1)
-		batt_pres = GPIO_ID_1_EC_BATT_PRES_ODL;
-	else
-		batt_pres = GPIO_EC_BATT_PRES_ODL;
-
-	/* The GPIO is low when the battery is physically present */
-	return gpio_get_level(batt_pres) ? BP_NO : BP_YES;
-}
-
-/*
- * Explicitly apply the board ID 1 *gpio.inc settings to pins that
- * were reassigned on current boards.
- */
-
-static void set_board_id_1_gpios(void)
-{
-	if (get_board_id() != 1)
-		return;
-
-	gpio_set_flags(GPIO_ID_1_EC_KB_BL_EN, GPIO_OUT_LOW);
-}
-DECLARE_HOOK(HOOK_INIT, set_board_id_1_gpios, HOOK_PRIO_FIRST);
-
-/*
- * Reclaim GPIO pins on board ID 1 that are used as ADC inputs on
- * current boards. ALT function group MODULE_ADC pins are set in
- * HOOK_PRIO_INIT_ADC and can be reclaimed right after the hook runs.
- */
-
-static void board_id_1_reclaim_adc(void)
-{
-	if (get_board_id() != 1)
-		return;
-
-	/*
-	 * GPIO_ID_1_USB_C0_C2_TCPC_RST_ODL is on GPIO34
-	 *
-	 * The TCPC has already been reset by board_tcpc_init() executed
-	 * from HOOK_PRIO_INIT_CHIPSET. Later, the pin gets set to ADC6
-	 * in HOOK_PRIO_INIT_ADC, so we simply need to set the pin back
-	 * to GPIO34.
-	 */
-	gpio_set_flags(GPIO_ID_1_USB_C0_C2_TCPC_RST_ODL, GPIO_ODR_HIGH);
-	gpio_set_alternate_function(GPIO_PORT_3, BIT(4), GPIO_ALT_FUNC_NONE);
-
-	/*
-	 * The pin gets set to ADC7 in HOOK_PRIO_INIT_ADC, so we simply
-	 * need to set it back to GPIOE1.
-	 */
-	gpio_set_flags(GPIO_ID_1_EC_BATT_PRES_ODL, GPIO_INPUT);
-	gpio_set_alternate_function(GPIO_PORT_E, BIT(1), GPIO_ALT_FUNC_NONE);
 }
-DECLARE_HOOK(HOOK_INIT, board_id_1_reclaim_adc, HOOK_PRIO_INIT_ADC + 1);
diff --git a/board/brask/board.h b/board/brask/board.h
index d7ca163bad..50d86eeadd 100644
--- a/board/brask/board.h
+++ b/board/brask/board.h
@@ -1,81 +1,20 @@
-/* Copyright 2020 The Chromium OS Authors. All rights reserved.
+/* Copyright 2021 The Chromium OS Authors. All rights reserved.
  * Use of this source code is governed by a BSD-style license that can be
  * found in the LICENSE file.
  */
 
-/* Brya board configuration */
+/* Brask board configuration */
 
 #ifndef __CROS_EC_BOARD_H
 #define __CROS_EC_BOARD_H
 
 #include "compile_time_macros.h"
 
-/*
- * Early brya boards are not set up for vivaldi
- */
-#undef CONFIG_KEYBOARD_VIVALDI
-
 /* Baseboard features */
 #include "baseboard.h"
 
-/*
- * This will happen automatically on NPCX9 ES2 and later. Do not remove
- * until we can confirm all earlier chips are out of service.
- */
-#define CONFIG_HIBERNATE_PSL_VCC1_RST_WAKEUP
-
 #define CONFIG_MP2964
 
-/* LED */
-#define CONFIG_LED_PWM
-#define CONFIG_LED_PWM_COUNT 2
-#undef CONFIG_LED_PWM_NEAR_FULL_COLOR
-#undef CONFIG_LED_PWM_SOC_ON_COLOR
-#undef CONFIG_LED_PWM_SOC_SUSPEND_COLOR
-#undef CONFIG_LED_PWM_LOW_BATT_COLOR
-#define CONFIG_LED_PWM_NEAR_FULL_COLOR EC_LED_COLOR_WHITE
-#define CONFIG_LED_PWM_SOC_ON_COLOR EC_LED_COLOR_WHITE
-#define CONFIG_LED_PWM_SOC_SUSPEND_COLOR EC_LED_COLOR_WHITE
-#define CONFIG_LED_PWM_LOW_BATT_COLOR EC_LED_COLOR_AMBER
-
-/* Sensors */
-#define CONFIG_ACCELGYRO_LSM6DSO	/* Base accel */
-#define CONFIG_ACCEL_LSM6DSO_INT_EVENT \
-	TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
-
-/* TCS3400 ALS */
-#define CONFIG_ALS
-#define ALS_COUNT 1
-#define CONFIG_ALS_TCS3400
-#define CONFIG_ALS_TCS3400_INT_EVENT \
-	TASK_EVENT_MOTION_SENSOR_INTERRUPT(CLEAR_ALS)
-
-/* Enable sensor fifo, must also define the _SIZE and _THRES */
-#define CONFIG_ACCEL_FIFO
-/* FIFO size is in power of 2. */
-#define CONFIG_ACCEL_FIFO_SIZE 256
-/* Depends on how fast the AP boots and typical ODRs */
-#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3)
-
-/* Sensors without hardware FIFO are in forced mode */
-#define CONFIG_ACCEL_FORCE_MODE_MASK \
-	(BIT(LID_ACCEL) | BIT(CLEAR_ALS))
-
-/* Lid accel */
-#define CONFIG_LID_ANGLE
-#define CONFIG_LID_ANGLE_SENSOR_BASE	BASE_ACCEL
-#define CONFIG_LID_ANGLE_SENSOR_LID	LID_ACCEL
-#define CONFIG_ACCEL_LIS2DWL
-#define CONFIG_ACCEL_LIS2DW_AS_BASE
-#define CONFIG_ACCEL_LIS2DW12_INT_EVENT \
-	TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL)
-
-#define CONFIG_ACCEL_INTERRUPTS
-
-/* Sensor console commands */
-#define CONFIG_CMD_ACCELS
-#define CONFIG_CMD_ACCEL_INFO
-
 /* USB Type A Features */
 #define USB_PORT_COUNT			1
 #define CONFIG_USB_PORT_POWER_DUMB
@@ -115,16 +54,13 @@
 #define GPIO_AC_PRESENT			GPIO_ACOK_OD
 #define GPIO_CPU_PROCHOT		GPIO_EC_PROCHOT_ODL
 #define GPIO_EC_INT_L			GPIO_EC_PCH_INT_ODL
-#define GPIO_ENABLE_BACKLIGHT		GPIO_EC_EN_EDP_BL
 #define GPIO_ENTERING_RW		GPIO_EC_ENTERING_RW
-#define GPIO_KBD_KSO2			GPIO_EC_KSO_02_INV
 #define GPIO_PACKET_MODE_EN		GPIO_EC_GSC_PACKET_MODE
 #define GPIO_PCH_PWRBTN_L		GPIO_EC_PCH_PWR_BTN_ODL
 #define GPIO_PCH_RSMRST_L		GPIO_EC_PCH_RSMRST_L
 #define GPIO_PCH_RTCRST			GPIO_EC_PCH_RTCRST
 #define GPIO_PCH_SLP_S0_L		GPIO_SYS_SLP_S0IX_L
 #define GPIO_PCH_SLP_S3_L		GPIO_SLP_S3_L
-#define GMR_TABLET_MODE_GPIO_L		GPIO_TABLET_MODE_L
 
 /*
  * GPIO_EC_PCH_INT_ODL is used for MKBP events as well as a PCH wakeup
@@ -137,15 +73,8 @@
 #define GPIO_POWER_BUTTON_L		GPIO_GSC_EC_PWR_BTN_ODL
 #define GPIO_RSMRST_L_PGOOD		GPIO_SEQ_EC_RSMRST_ODL
 #define GPIO_SYS_RESET_L		GPIO_SYS_RST_ODL
-#define GPIO_VOLUME_DOWN_L		GPIO_EC_VOLDN_BTN_ODL
-#define GPIO_VOLUME_UP_L		GPIO_EC_VOLUP_BTN_ODL
 #define GPIO_WP_L			GPIO_EC_WP_ODL
 
-#define GPIO_ID_1_EC_KB_BL_EN		GPIO_EC_BATT_PRES_ODL
-
-/* System has back-lit keyboard */
-#define CONFIG_PWM_KBLIGHT
-
 /* I2C Bus Configuration */
 
 #define I2C_PORT_SENSOR		NPCX_I2C_PORT0_0
@@ -192,18 +121,15 @@
 #define CONFIG_TEMP_SENSOR_POWER_GPIO	GPIO_SEQ_EC_DSW_PWROK
 #define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B
 
+/* ADC */
+#define CONFIG_ADC
+
 /*
- * TODO(b/181271666): no fan control loop until sensors are tuned
+ * TODO(b/197478860): Enable the fan control. We need
+ * to check the sensor value and adjust the fan speed.
  */
 /* #define CONFIG_FANS			FAN_CH_COUNT */
 
-/* Charger defines */
-#define CONFIG_CHARGER_BQ25720
-#define CONFIG_CHARGER_BQ25720_VSYS_TH2_DV	70
-#define CONFIG_CHARGE_RAMP_SW
-#define CONFIG_CHARGER_SENSE_RESISTOR		10
-#define CONFIG_CHARGER_SENSE_RESISTOR_AC	10
-
 #ifndef __ASSEMBLER__
 
 #include "gpio_signal.h"	/* needed by registers.h */
@@ -215,6 +141,7 @@ enum adc_channel {
 	ADC_TEMP_SENSOR_2_FAN,
 	ADC_TEMP_SENSOR_3_CHARGER,
 	ADC_TEMP_SENSOR_4_WWAN,
+	ADC_VBUS,
 	ADC_CH_COUNT
 };
 
@@ -224,15 +151,6 @@ enum temp_sensor_id {
 	TEMP_SENSOR_COUNT
 };
 
-enum sensor_id {
-	LID_ACCEL = 0,
-	BASE_ACCEL,
-	BASE_GYRO,
-	CLEAR_ALS,
-	RGB_ALS,
-	SENSOR_COUNT
-};
-
 enum ioex_port {
 	IOEX_C0_NCT38XX = 0,
 	IOEX_C2_NCT38XX,
@@ -241,19 +159,8 @@ enum ioex_port {
 	IOEX_PORT_COUNT
 };
 
-enum battery_type {
-	BATTERY_POWER_TECH,
-	BATTERY_LGC011,
-	BATTERY_TYPE_COUNT
-};
-
 enum pwm_channel {
-	PWM_CH_LED2 = 0,		/* PWM0 (white charger) */
-	PWM_CH_LED3,			/* PWM1 (orange on DB) */
-	PWM_CH_LED1,			/* PWM2 (orange charger) */
-	PWM_CH_KBLIGHT,			/* PWM3 */
 	PWM_CH_FAN,			/* PWM5 */
-	PWM_CH_LED4,			/* PWM7 (white on DB) */
 	PWM_CH_COUNT
 };
 
diff --git a/board/brask/build.mk b/board/brask/build.mk
index b4ad2e3283..4bf53631b1 100644
--- a/board/brask/build.mk
+++ b/board/brask/build.mk
@@ -1,9 +1,9 @@
 # -*- makefile -*-
-# Copyright 2020 The Chromium OS Authors. All rights reserved.
+# Copyright 2021 The Chromium OS Authors. All rights reserved.
 # Use of this source code is governed by a BSD-style license that can be
 # found in the LICENSE file.
 #
-# Brya board specific files build
+# Brask board specific files build
 #
 
 CHIP:=npcx
@@ -12,14 +12,9 @@ CHIP_VARIANT:=npcx9m3f
 BASEBOARD:=brask
 
 board-y=
-board-y+=battery.o
 board-y+=board.o
-board-y+=fans.o
 board-y+=fw_config.o
 board-y+=i2c.o
-board-y+=keyboard.o
-board-y+=led.o
 board-y+=pwm.o
 board-y+=sensors.o
-board-y+=tune_mp2964.o
 board-y+=usbc_config.o
diff --git a/board/brask/ec.tasklist b/board/brask/ec.tasklist
index 470a1fcdde..86693f82a5 100644
--- a/board/brask/ec.tasklist
+++ b/board/brask/ec.tasklist
@@ -1,4 +1,4 @@
-/* Copyright 2020 The Chromium OS Authors. All rights reserved.
+/* Copyright 2021 The Chromium OS Authors. All rights reserved.
  * Use of this source code is governed by a BSD-style license that can be
  * found in the LICENSE file.
  */
@@ -12,18 +12,13 @@
 
 #define CONFIG_TASK_LIST \
 	TASK_ALWAYS(HOOKS, hook_task, NULL, LARGER_TASK_STACK_SIZE) \
-	TASK_ALWAYS(CHG_RAMP, chg_ramp_task, NULL, TASK_STACK_SIZE) \
 	TASK_ALWAYS(USB_CHG_P0, usb_charger_task, 0, TASK_STACK_SIZE) \
 	TASK_ALWAYS(USB_CHG_P1, usb_charger_task, 0, TASK_STACK_SIZE) \
 	TASK_ALWAYS(USB_CHG_P2, usb_charger_task, 0, TASK_STACK_SIZE) \
-	TASK_ALWAYS(CHARGER, charger_task, NULL, VENTI_TASK_STACK_SIZE) \
-	TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \
-	TASK_NOTEST(KEYPROTO, keyboard_protocol_task, NULL, TASK_STACK_SIZE) \
 	TASK_NOTEST(CHIPSET, chipset_task, NULL, LARGER_TASK_STACK_SIZE) \
 	TASK_ALWAYS(HOSTCMD, host_command_task, NULL, LARGER_TASK_STACK_SIZE) \
 	TASK_ALWAYS(CONSOLE, console_task, NULL, VENTI_TASK_STACK_SIZE) \
 	TASK_ALWAYS(POWERBTN, power_button_task, NULL, LARGER_TASK_STACK_SIZE) \
-	TASK_NOTEST(KEYSCAN, keyboard_scan_task, NULL, TASK_STACK_SIZE) \
 	TASK_ALWAYS(PD_C0, pd_task, NULL, VENTI_TASK_STACK_SIZE) \
 	TASK_ALWAYS(PD_C1, pd_task, NULL, VENTI_TASK_STACK_SIZE) \
 	TASK_ALWAYS(PD_C2, pd_task, NULL, VENTI_TASK_STACK_SIZE) \
diff --git a/board/brask/fans.c b/board/brask/fans.c
deleted file mode 100644
index d966056331..0000000000
--- a/board/brask/fans.c
+++ /dev/null
@@ -1,88 +0,0 @@
-/* Copyright 2021 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Physical fans. These are logically separate from pwm_channels. */
-
-#include "common.h"
-#include "compile_time_macros.h"
-#include "console.h"
-#include "fan_chip.h"
-#include "fan.h"
-#include "hooks.h"
-#include "pwm.h"
-
-/* MFT channels. These are logically separate from pwm_channels. */
-const struct mft_t mft_channels[] = {
-	[MFT_CH_0] = {
-		.module = NPCX_MFT_MODULE_1,
-		.clk_src = TCKC_LFCLK,
-		.pwm_id = PWM_CH_FAN,
-	},
-};
-BUILD_ASSERT(ARRAY_SIZE(mft_channels) == MFT_CH_COUNT);
-
-static const struct fan_conf fan_conf_0 = {
-	.flags = FAN_USE_RPM_MODE,
-	.ch = MFT_CH_0,	/* Use MFT id to control fan */
-	.pgood_gpio = -1,
-	.enable_gpio = GPIO_EN_PP5000_FAN,
-};
-
-/*
- * TOOD(b/180681346): need to update for real fan
- *
- * Prototype fan spins at about 7200 RPM at 100% PWM.
- * Set minimum at around 30% PWM.
- */
-static const struct fan_rpm fan_rpm_0 = {
-	.rpm_min = 2200,
-	.rpm_start = 2200,
-	.rpm_max = 7200,
-};
-
-const struct fan_t fans[FAN_CH_COUNT] = {
-	[FAN_CH_0] = {
-		.conf = &fan_conf_0,
-		.rpm = &fan_rpm_0,
-	},
-};
-
-#ifndef CONFIG_FANS
-
-/*
- * TODO(b/181271666): use static fan speeds until fan and sensors are
- * tuned. for now, use:
- *
- *   AP off:  33%
- *   AP  on: 100%
- */
-
-static void fan_slow(void)
-{
-	const int duty_pct = 33;
-
-	ccprints("%s: speed %d%%", __func__, duty_pct);
-
-	pwm_enable(PWM_CH_FAN, 1);
-	pwm_set_duty(PWM_CH_FAN, duty_pct);
-}
-
-static void fan_max(void)
-{
-	const int duty_pct = 100;
-
-	ccprints("%s: speed %d%%", __func__, duty_pct);
-
-	pwm_enable(PWM_CH_FAN, 1);
-	pwm_set_duty(PWM_CH_FAN, duty_pct);
-}
-
-DECLARE_HOOK(HOOK_INIT, fan_slow, HOOK_PRIO_DEFAULT);
-DECLARE_HOOK(HOOK_CHIPSET_SUSPEND, fan_slow, HOOK_PRIO_DEFAULT);
-DECLARE_HOOK(HOOK_CHIPSET_SHUTDOWN, fan_slow, HOOK_PRIO_DEFAULT);
-DECLARE_HOOK(HOOK_CHIPSET_RESET, fan_max, HOOK_PRIO_FIRST);
-DECLARE_HOOK(HOOK_CHIPSET_RESUME, fan_max, HOOK_PRIO_DEFAULT);
-
-#endif /* CONFIG_FANS */
diff --git a/board/brask/fw_config.c b/board/brask/fw_config.c
index fb8acb635d..7afdae3837 100644
--- a/board/brask/fw_config.c
+++ b/board/brask/fw_config.c
@@ -32,21 +32,6 @@ void board_init_fw_config(void)
 		CPRINTS("CBI: Read FW_CONFIG failed, using board defaults");
 		fw_config = fw_config_defaults;
 	}
-
-	if (get_board_id() == 0) {
-		/*
-		 * Early boards have a zero'd out FW_CONFIG, so replace
-		 * it with a sensible default value. If DB_USB_ABSENT2
-		 * was used as an alternate encoding of DB_USB_ABSENT to
-		 * avoid the zero check, then fix it.
-		 */
-		if (fw_config.raw_value == 0) {
-			CPRINTS("CBI: FW_CONFIG is zero, using board defaults");
-			fw_config = fw_config_defaults;
-		} else if (fw_config.usb_db == DB_USB_ABSENT2) {
-			fw_config.usb_db = DB_USB_ABSENT;
-		}
-	}
 }
 
 union brya_cbi_fw_config get_fw_config(void)
diff --git a/board/brask/gpio.inc b/board/brask/gpio.inc
index 0f69feb979..d083a4422d 100644
--- a/board/brask/gpio.inc
+++ b/board/brask/gpio.inc
@@ -5,26 +5,17 @@
  * found in the LICENSE file.
  */
 
-#define MODULE_KB		MODULE_KEYBOARD_SCAN
-
 /* INTERRUPT GPIOs: */
-GPIO_INT(ACOK_OD,                    PIN(0, 0), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, extpower_interrupt)
-GPIO_INT(EC_ACCEL_INT_R_L,           PIN(8, 1), GPIO_SEL_1P8V | GPIO_INT_FALLING, lis2dw12_interrupt)
-GPIO_INT(EC_ALS_RGB_INT_R_L,         PIN(D, 4), GPIO_INT_FALLING, tcs3400_interrupt)
-GPIO_INT(EC_IMU_INT_R_L,             PIN(5, 6), GPIO_SEL_1P8V | GPIO_INT_FALLING, lsm6dso_interrupt)
+GPIO_INT(ACOK_OD,                    PIN(0, 0), GPIO_INT_BOTH, extpower_interrupt)
 GPIO_INT(EC_PROCHOT_IN_L,            PIN(F, 0), GPIO_INT_BOTH, throttle_ap_prochot_input_interrupt)
-GPIO_INT(EC_VOLDN_BTN_ODL,           PIN(9, 3), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt)
-GPIO_INT(EC_VOLUP_BTN_ODL,           PIN(9, 7), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt)
 GPIO_INT(EC_WP_ODL,                  PIN(A, 1), GPIO_INT_BOTH, switch_interrupt)
-GPIO_INT(GSC_EC_PWR_BTN_ODL,         PIN(0, 1), GPIO_INT_BOTH | GPIO_HIB_WAKE_LOW, power_button_interrupt)
-GPIO_INT(LID_OPEN,                   PIN(D, 2), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, lid_interrupt)
+GPIO_INT(GSC_EC_PWR_BTN_ODL,         PIN(0, 1), GPIO_INT_BOTH, power_button_interrupt)
 GPIO_INT(SEQ_EC_ALL_SYS_PG,          PIN(F, 4), GPIO_INT_BOTH, power_signal_interrupt)
 GPIO_INT(SEQ_EC_DSW_PWROK,           PIN(C, 7), GPIO_INT_BOTH, power_signal_interrupt)
 GPIO_INT(SEQ_EC_RSMRST_ODL,          PIN(E, 2), GPIO_INT_BOTH, power_signal_interrupt)
 GPIO_INT(SLP_S3_L,                   PIN(A, 5), GPIO_INT_BOTH, power_signal_interrupt)
 GPIO_INT(SLP_SUS_L,                  PIN(F, 1), GPIO_INT_BOTH, power_signal_interrupt)
 GPIO_INT(SYS_SLP_S0IX_L,             PIN(D, 5), GPIO_INT_BOTH, power_signal_interrupt)
-GPIO_INT(TABLET_MODE_L,              PIN(9, 5), GPIO_INT_BOTH, gmr_tablet_switch_isr)
 GPIO_INT(USB_C0_BC12_INT_ODL,        PIN(C, 6), GPIO_INT_FALLING, bc12_interrupt)
 GPIO_INT(USB_C0_C2_TCPC_INT_ODL,     PIN(E, 0), GPIO_INT_FALLING, tcpc_alert_event)
 GPIO_INT(USB_C0_PPC_INT_ODL,         PIN(6, 2), GPIO_INT_FALLING, ppc_interrupt)
@@ -38,9 +29,7 @@ GPIO_INT(USB_C2_RT_INT_ODL,          PIN(4, 1), GPIO_INT_FALLING, retimer_interr
 
 /* USED GPIOs: */
 GPIO(CCD_MODE_ODL,                   PIN(E, 5), GPIO_INPUT)
-GPIO(CHARGER_VAP_OTG_EN,             PIN(7, 3), GPIO_OUT_LOW)
 GPIO(CPU_C10_GATE_L,                 PIN(6, 7), GPIO_INPUT)
-GPIO(EC_BATT_PRES_ODL,               PIN(A, 3), GPIO_INPUT)
 GPIO(EC_ENTERING_RW,                 PIN(0, 3), GPIO_OUT_LOW)
 GPIO(EC_EN_EDP_BL,                   PIN(D, 3), GPIO_OUT_HIGH)
 GPIO(EC_GSC_PACKET_MODE,             PIN(7, 5), GPIO_OUT_LOW)
@@ -60,7 +49,6 @@ GPIO(EC_I2C_USB_C1_MIX_SCL,          PIN(E, 4), GPIO_INPUT)
 GPIO(EC_I2C_USB_C1_MIX_SDA,          PIN(E, 3), GPIO_INPUT)
 GPIO(EC_I2C_USB_C1_TCPC_SCL,         PIN(F, 3), GPIO_INPUT)
 GPIO(EC_I2C_USB_C1_TCPC_SDA,         PIN(F, 2), GPIO_INPUT)
-GPIO(EC_KB_BL_EN_L,                  PIN(8, 6), GPIO_OUT_HIGH)
 GPIO(EC_PCHHOT_ODL,                  PIN(7, 4), GPIO_INPUT)
 GPIO(EC_PCH_INT_ODL,                 PIN(B, 0), GPIO_ODR_HIGH)
 GPIO(EC_PCH_PWR_BTN_ODL,             PIN(C, 1), GPIO_ODR_HIGH)
@@ -107,14 +95,6 @@ ALTERNATE(PIN_MASK(3, 0x10), 0, MODULE_ADC, 0)               /* GPIO34/PS2_DAT2/
 ALTERNATE(PIN_MASK(4, 0x34), 0, MODULE_ADC, 0)               /* GPIO42/ADC3/RI_L, GPIO45/ADC0, GPIO44/ADC1 */
 ALTERNATE(PIN_MASK(E, 0x02), 0, MODULE_ADC, 0)               /* GPIOE1/ADC7 */
 
-/* KB alternate functions */
-ALTERNATE(PIN_MASK(0, 0xf0), 0, MODULE_KB, GPIO_ODR_HIGH)    /* KSO10&P80_CLK/GPIO07, KSO11&P80_DAT/GPIO06, KSO12/GPIO05, KSO13/GPIO04 */
-ALTERNATE(PIN_MASK(1, 0x7f), 0, MODULE_KB, GPIO_ODR_HIGH)    /* KSO06/GPO13/GP_SEL_L, KSO07/GPO12/JEN_L, KSO03/GPIO16/JTAG_TDO0_SWO, KSO04/GPIO15/XNOR, KSO05/GPIO14, KSO08/GPIO11/CR_SOUT1, KSO09/GPIO10/CR_SIN1 */
-ALTERNATE(PIN_MASK(2, 0xfc), 0, MODULE_KB, GPIO_INPUT | GPIO_PULL_UP) /* KSI2/GPIO27/TRACEDATA1, KSI3/GPIO26/TRACEDATA0, KSI4/GPIO25/TRACECLK/GP_SCLK, KSI5/GPIO24/GP_MISO, KSI6/GPIO23/S_SBUB, KSI7/GPIO22/S_SBUA */
-ALTERNATE(PIN_MASK(2, 0x03), 0, MODULE_KB, GPIO_ODR_HIGH)    /* KSO00/GPIO21/JTAG_TCK_SWCLK, KSO01/GPIO20/JTAG_TMS_SWIO */
-ALTERNATE(PIN_MASK(3, 0x03), 0, MODULE_KB, GPIO_INPUT | GPIO_PULL_UP) /* KSI0/GPIO31/TRACEDATA3/GP_MOSI, KSI1/GPIO30/TRACEDATA2/GP_CS_L */
-ALTERNATE(PIN_MASK(8, 0x04), 0, MODULE_KB, GPIO_ODR_HIGH)    /* KSO14/GPIO82 */
-
 /* PMU alternate functions */
 ALTERNATE(PIN_MASK(0, 0x01), 0, MODULE_PMU, GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH) /* PSL_IN2_L&GPI00/GPIO00 */
 ALTERNATE(PIN_MASK(0, 0x02), 0, MODULE_PMU, GPIO_INT_BOTH | GPIO_HIB_WAKE_LOW) /* GPIO01/PSL_IN3_L&GPI01 */
@@ -125,45 +105,6 @@ UNUSED(PIN(D, 6))       /* GPOD6/CR_SOUT3/SHDF_ESPI_L */
 UNUSED(PIN(3, 2))       /* GPO32/TRIS_L */
 UNUSED(PIN(3, 5))       /* GPO35/CR_SOUT4/TEST_L */
 UNUSED(PIN(6, 6))       /* GPIO66 */
-/*
- * The NPCX keyboard driver does not use named GPIOs to access
- * keyboard scan pins, so we do not list them in *gpio.inc. However, when
- * KEYBOARD_COL2_INVERTED is defined, this name is required.
- */
-GPIO(EC_KSO_02_INV,               PIN(1, 7), GPIO_OUT_LOW)
-
-/*
- * GPIOE1 is an ALT function ADC INPUT on board ID 2 and a GPIO INPUT on
- * board ID 1. This declaration gives us a signal name to use on board
- * ID 1.
- */
-GPIO(ID_1_EC_BATT_PRES_ODL,       PIN(E, 1), GPIO_INPUT)
-
-/*
- * GPIO34 is an INPUT on board ID 2 and ODR_LOW on board ID 1.
- *
- * Since this pin is pulled up to 3.3V through a 30.9K ohm resistor on
- * board ID 2, we will leak about 0.3mW until the pin is put in ALT mode
- * when MODULE_ADC configuration runs. Initializing the pin to ODR_LOW
- * gives us full control on both boards.
- */
-GPIO(ID_1_USB_C0_C2_TCPC_RST_ODL, PIN(3, 4), GPIO_ODR_LOW)
-
-/* Board ID 1 IO expander configuration */
-
-IOEX(ID_1_USB_C0_RT_RST_ODL, EXPIN(IOEX_ID_1_C0_NCT38XX, 0, 2), GPIO_ODR_LOW)
-/* GPIO03_P1 to PU */
-IOEX(ID_1_USB_C0_FRS_EN,     EXPIN(IOEX_ID_1_C0_NCT38XX, 0, 4), GPIO_LOW)
-IOEX(ID_1_USB_C0_OC_ODL,     EXPIN(IOEX_ID_1_C0_NCT38XX, 0, 6), GPIO_ODR_HIGH)
-/* GPIO07_P1 to PU */
-
-IOEX(ID_1_USB_C2_RT_RST_ODL, EXPIN(IOEX_ID_1_C2_NCT38XX, 0, 2), GPIO_ODR_LOW)
-/* GPIO03_P2 to PU */
-IOEX(ID_1_USB_C2_FRS_EN,     EXPIN(IOEX_ID_1_C2_NCT38XX, 0, 4), GPIO_LOW)
-IOEX(ID_1_USB_C1_OC_ODL,     EXPIN(IOEX_ID_1_C2_NCT38XX, 0, 6), GPIO_ODR_HIGH)
-IOEX(ID_1_USB_C2_OC_ODL,     EXPIN(IOEX_ID_1_C2_NCT38XX, 0, 7), GPIO_ODR_HIGH)
-
-/* Board ID 2 IO expander configuration */
 
 /* GPIO02_P2 to PU */
 /* GPIO03_P2 to PU */
diff --git a/board/brask/keyboard.c b/board/brask/keyboard.c
deleted file mode 100644
index a9f033130d..0000000000
--- a/board/brask/keyboard.c
+++ /dev/null
@@ -1,25 +0,0 @@
-/* Copyright 2021 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-#include "common.h"
-
-#include "keyboard_scan.h"
-#include "timer.h"
-
-/* Keyboard scan setting */
-__override struct keyboard_scan_config keyscan_config = {
-	/* Increase from 50 us, because KSO_02 passes through the H1. */
-	.output_settle_us = 80,
-	/* Other values should be the same as the default configuration. */
-	.debounce_down_us = 9 * MSEC,
-	.debounce_up_us = 30 * MSEC,
-	.scan_period_us = 3 * MSEC,
-	.min_post_scan_delay_us = 1000,
-	.poll_timeout_us = 100 * MSEC,
-	.actual_key_mask = {
-		0x14, 0xff, 0xff, 0xff, 0xff, 0xf5, 0xff,
-		0xa4, 0xff, 0xfe, 0x55, 0xfa, 0xca  /* full set */
-	},
-};
diff --git a/board/brask/led.c b/board/brask/led.c
deleted file mode 100644
index 38caa38d37..0000000000
--- a/board/brask/led.c
+++ /dev/null
@@ -1,93 +0,0 @@
-/* Copyright 2021 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Brya specific PWM LED settings: there are 2 LEDs on each side of the board,
- * each one can be controlled separately. The LED colors are white or amber,
- * and the default behavior is tied to the charging process: both sides are
- * amber while charging the battery and white when the battery is charged.
- */
-
-#include <stdint.h>
-
-#include "common.h"
-#include "compile_time_macros.h"
-#include "ec_commands.h"
-#include "led_pwm.h"
-#include "pwm.h"
-#include "util.h"
-
-const enum ec_led_id supported_led_ids[] = {
-	EC_LED_ID_LEFT_LED,
-	EC_LED_ID_RIGHT_LED,
-};
-
-const int supported_led_ids_count = ARRAY_SIZE(supported_led_ids);
-
-/*
- * We only have a white and an amber LED, so setting any other color results in
- * both LEDs being off.
- */
-struct pwm_led led_color_map[EC_LED_COLOR_COUNT] = {
-				/* Amber, White */
-	[EC_LED_COLOR_RED]    = {   0,   0 },
-	[EC_LED_COLOR_GREEN]  = {   0,   0 },
-	[EC_LED_COLOR_BLUE]   = {   0,   0 },
-	[EC_LED_COLOR_YELLOW] = {   0,   0 },
-	[EC_LED_COLOR_WHITE]  = {   0, 100 },
-	[EC_LED_COLOR_AMBER]  = {  100,  0 },
-};
-
-/* Two logical LEDs with amber and white channels. */
-struct pwm_led pwm_leds[CONFIG_LED_PWM_COUNT] = {
-	{
-		.ch0 = PWM_CH_LED1,
-		.ch1 = PWM_CH_LED2,
-		.ch2 = PWM_LED_NO_CHANNEL,
-		.enable = &pwm_enable,
-		.set_duty = &pwm_set_duty,
-	},
-	{
-		.ch0 = PWM_CH_LED3,
-		.ch1 = PWM_CH_LED4,
-		.ch2 = PWM_LED_NO_CHANNEL,
-		.enable = &pwm_enable,
-		.set_duty = &pwm_set_duty,
-	},
-};
-
-void led_get_brightness_range(enum ec_led_id led_id, uint8_t *brightness_range)
-{
-	memset(brightness_range, '\0',
-	       sizeof(*brightness_range) * EC_LED_COLOR_COUNT);
-	brightness_range[EC_LED_COLOR_AMBER] = 100;
-	brightness_range[EC_LED_COLOR_WHITE] = 100;
-}
-
-int led_set_brightness(enum ec_led_id led_id, const uint8_t *brightness)
-{
-	enum pwm_led_id pwm_id;
-
-	/* Convert ec_led_id to pwm_led_id. */
-	switch (led_id) {
-	case EC_LED_ID_LEFT_LED:
-		pwm_id = PWM_LED0;
-		break;
-	case EC_LED_ID_RIGHT_LED:
-		pwm_id = PWM_LED1;
-		break;
-	default:
-		return EC_ERROR_UNKNOWN;
-	}
-
-	if (brightness[EC_LED_COLOR_WHITE])
-		set_pwm_led_color(pwm_id, EC_LED_COLOR_WHITE);
-	else if (brightness[EC_LED_COLOR_AMBER])
-		set_pwm_led_color(pwm_id, EC_LED_COLOR_AMBER);
-	else
-		/* Otherwise, the "color" is "off". */
-		set_pwm_led_color(pwm_id, -1);
-
-	return EC_SUCCESS;
-}
diff --git a/board/brask/pwm.c b/board/brask/pwm.c
index 6e662f8e7d..aab092d407 100644
--- a/board/brask/pwm.c
+++ b/board/brask/pwm.c
@@ -11,61 +11,22 @@
 #include "pwm_chip.h"
 
 const struct pwm_t pwm_channels[] = {
-	[PWM_CH_LED2] = {
-		.channel = 0,
-		.flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP,
-		.freq = 4800,
-	},
-	[PWM_CH_LED3] = {
-		.channel = 1,
-		.flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP,
-		.freq = 4800,
-	},
-	[PWM_CH_LED1] = {
-		.channel = 2,
-		.flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP,
-		.freq = 4800,
-	},
-	[PWM_CH_KBLIGHT] = {
-		.channel = 3,
-		.flags = 0,
-		/*
-		 * Set PWM frequency to multiple of 50 Hz and 60 Hz to prevent
-		 * flicker. Higher frequencies consume similar average power to
-		 * lower PWM frequencies, but higher frequencies record a much
-		 * lower maximum power.
-		 */
-		.freq = 2400,
-	},
 	[PWM_CH_FAN] = {
 		.channel = 5,
 		.flags = PWM_CONFIG_OPEN_DRAIN | PWM_CONFIG_DSLEEP,
 		.freq = 1000
 	},
-	[PWM_CH_LED4] = {
-		.channel = 7,
-		.flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP,
-		.freq = 4800,
-	},
 };
 BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT);
 
 static void board_pwm_init(void)
 {
 	/*
-	 * Turn on all the LED at 50%.
-	 * Turn on the fan at 100%.
+	 * TODO(b/197478860): Turn on the fan at 100% by default
+	 * We need to find tune the fan speed according to the
+	 * thermal sensor value.
 	 */
-	pwm_enable(PWM_CH_LED1, 1);
-	pwm_set_duty(PWM_CH_LED1, 50);
-	pwm_enable(PWM_CH_LED2, 1);
-	pwm_set_duty(PWM_CH_LED2, 50);
-	pwm_enable(PWM_CH_LED3, 1);
-	pwm_set_duty(PWM_CH_LED3, 50);
-	pwm_enable(PWM_CH_LED4, 1);
-	pwm_set_duty(PWM_CH_LED4, 50);
-
-	pwm_enable(PWM_CH_KBLIGHT, 1);
-	pwm_set_duty(PWM_CH_KBLIGHT, 50);
+	pwm_enable(PWM_CH_FAN, 1);
+	pwm_set_duty(PWM_CH_FAN, 100);
 }
 DECLARE_HOOK(HOOK_INIT, board_pwm_init, HOOK_PRIO_DEFAULT);
diff --git a/board/brask/sensors.c b/board/brask/sensors.c
index e80d5f912a..71a4ee4dc0 100644
--- a/board/brask/sensors.c
+++ b/board/brask/sensors.c
@@ -4,13 +4,8 @@
  */
 
 #include "common.h"
-#include "accelgyro.h"
 #include "adc_chip.h"
-#include "driver/accel_lis2dw12.h"
-#include "driver/accelgyro_lsm6dso.h"
-#include "driver/als_tcs3400_public.h"
 #include "hooks.h"
-#include "motion_sense.h"
 #include "temp_sensor.h"
 #include "thermal.h"
 #include "temp_sensor/thermistor.h"
@@ -45,228 +40,14 @@ const struct adc_t adc_channels[] = {
 		.factor_div = ADC_READ_MAX + 1,
 		.shift = 0,
 	},
-};
-BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT);
-
-K_MUTEX_DEFINE(g_lid_accel_mutex);
-K_MUTEX_DEFINE(g_base_accel_mutex);
-static struct stprivate_data g_lis2dw12_data;
-static struct lsm6dso_data lsm6dso_data;
-
-/* TODO(b/184779333): calibrate the orientation matrix on later board stage */
-static const mat33_fp_t lid_standard_ref = {
-	{ 0, FLOAT_TO_FP(1), 0},
-	{ FLOAT_TO_FP(1), 0, 0},
-	{ 0, 0, FLOAT_TO_FP(-1)}
-};
-
-/* TODO(b/184779743): verify orientation matrix */
-static const mat33_fp_t base_standard_ref = {
-	{ FLOAT_TO_FP(1), 0, 0},
-	{ 0, FLOAT_TO_FP(-1), 0},
-	{ 0, 0, FLOAT_TO_FP(-1)}
-};
-
-/* TCS3400 private data */
-static struct als_drv_data_t g_tcs3400_data = {
-	.als_cal.scale = 1,
-	.als_cal.uscale = 0,
-	.als_cal.offset = 0,
-	.als_cal.channel_scale = {
-		.k_channel_scale = ALS_CHANNEL_SCALE(1.0), /* kc from VPD */
-		.cover_scale = ALS_CHANNEL_SCALE(1.0),     /* CT */
-	},
-};
-
-/*
- * TODO: b/184702900 need to calibrate ALS/RGB sensor. At default settings,
- * shining phone flashlight on sensor pegs all readings at 0xFFFF.
- */
-static struct tcs3400_rgb_drv_data_t g_tcs3400_rgb_data = {
-	.calibration.rgb_cal[X] = {
-		.offset = 0,
-		.coeff[TCS_RED_COEFF_IDX] = FLOAT_TO_FP(0),
-		.coeff[TCS_GREEN_COEFF_IDX] = FLOAT_TO_FP(0),
-		.coeff[TCS_BLUE_COEFF_IDX] = FLOAT_TO_FP(0),
-		.coeff[TCS_CLEAR_COEFF_IDX] = FLOAT_TO_FP(0),
-		.scale = {
-			.k_channel_scale = ALS_CHANNEL_SCALE(1.0), /* kr */
-			.cover_scale = ALS_CHANNEL_SCALE(1.0)
-		}
-	},
-	.calibration.rgb_cal[Y] = {
-		.offset = 0,
-		.coeff[TCS_RED_COEFF_IDX] = FLOAT_TO_FP(0),
-		.coeff[TCS_GREEN_COEFF_IDX] = FLOAT_TO_FP(0),
-		.coeff[TCS_BLUE_COEFF_IDX] = FLOAT_TO_FP(0),
-		.coeff[TCS_CLEAR_COEFF_IDX] = FLOAT_TO_FP(0),
-		.scale = {
-			.k_channel_scale = ALS_CHANNEL_SCALE(1.0), /* kg */
-			.cover_scale = ALS_CHANNEL_SCALE(1.0)
-		},
-	},
-	.calibration.rgb_cal[Z] = {
-		.offset = 0,
-		.coeff[TCS_RED_COEFF_IDX] = FLOAT_TO_FP(0),
-		.coeff[TCS_GREEN_COEFF_IDX] = FLOAT_TO_FP(0),
-		.coeff[TCS_BLUE_COEFF_IDX] = FLOAT_TO_FP(0),
-		.coeff[TCS_CLEAR_COEFF_IDX] = FLOAT_TO_FP(0),
-		.scale = {
-			.k_channel_scale = ALS_CHANNEL_SCALE(1.0), /* kb */
-			.cover_scale = ALS_CHANNEL_SCALE(1.0)
-		}
+	[ADC_VBUS] = {  /* 5/39 voltage divider */
+		.name = "VBUS",
+		.input_ch = NPCX_ADC_CH2,
+		.factor_mul = ADC_MAX_VOLT * 39,
+		.factor_div = (ADC_READ_MAX + 1) * 5,
 	},
-	.calibration.irt = INT_TO_FP(1),
-	.saturation.again = TCS_DEFAULT_AGAIN,
-	.saturation.atime = TCS_DEFAULT_ATIME,
 };
-
-struct motion_sensor_t motion_sensors[] = {
-	[LID_ACCEL] = {
-		.name = "Lid Accel",
-		.active_mask = SENSOR_ACTIVE_S0_S3,
-		.chip = MOTIONSENSE_CHIP_LIS2DW12,
-		.type = MOTIONSENSE_TYPE_ACCEL,
-		.location = MOTIONSENSE_LOC_LID,
-		.drv = &lis2dw12_drv,
-		.mutex = &g_lid_accel_mutex,
-		.drv_data = &g_lis2dw12_data,
-		.int_signal = GPIO_EC_ACCEL_INT_R_L,
-		.port = I2C_PORT_SENSOR,
-		.i2c_spi_addr_flags = LIS2DW12_ADDR0,
-		.flags = MOTIONSENSE_FLAG_INT_SIGNAL,
-		.rot_standard_ref = &lid_standard_ref, /* identity matrix */
-		.default_range = 2, /* g */
-		.min_frequency = LIS2DW12_ODR_MIN_VAL,
-		.max_frequency = LIS2DW12_ODR_MAX_VAL,
-		.config = {
-			/* EC use accel for angle detection */
-			[SENSOR_CONFIG_EC_S0] = {
-				.odr = 12500 | ROUND_UP_FLAG,
-			},
-			/* Sensor on for lid angle detection */
-			[SENSOR_CONFIG_EC_S3] = {
-				.odr = 10000 | ROUND_UP_FLAG,
-			},
-		},
-	},
-
-	[BASE_ACCEL] = {
-		.name = "Base Accel",
-		.active_mask = SENSOR_ACTIVE_S0_S3,
-		.chip = MOTIONSENSE_CHIP_LSM6DSO,
-		.type = MOTIONSENSE_TYPE_ACCEL,
-		.location = MOTIONSENSE_LOC_BASE,
-		.drv = &lsm6dso_drv,
-		.mutex = &g_base_accel_mutex,
-		.drv_data = LSM6DSO_ST_DATA(lsm6dso_data,
-				MOTIONSENSE_TYPE_ACCEL),
-		.int_signal = GPIO_EC_IMU_INT_R_L,
-		.flags = MOTIONSENSE_FLAG_INT_SIGNAL,
-		.port = I2C_PORT_SENSOR,
-		.i2c_spi_addr_flags = LSM6DSO_ADDR0_FLAGS,
-		.rot_standard_ref = &base_standard_ref,
-		.default_range = 4,  /* g */
-		.min_frequency = LSM6DSO_ODR_MIN_VAL,
-		.max_frequency = LSM6DSO_ODR_MAX_VAL,
-		.config = {
-			[SENSOR_CONFIG_EC_S0] = {
-				.odr = 13000 | ROUND_UP_FLAG,
-				.ec_rate = 100 * MSEC,
-			},
-			[SENSOR_CONFIG_EC_S3] = {
-				.odr = 10000 | ROUND_UP_FLAG,
-				.ec_rate = 100 * MSEC,
-			},
-		},
-	},
-
-	[BASE_GYRO] = {
-		.name = "Base Gyro",
-		.active_mask = SENSOR_ACTIVE_S0_S3,
-		.chip = MOTIONSENSE_CHIP_LSM6DSO,
-		.type = MOTIONSENSE_TYPE_GYRO,
-		.location = MOTIONSENSE_LOC_BASE,
-		.drv = &lsm6dso_drv,
-		.mutex = &g_base_accel_mutex,
-		.drv_data = LSM6DSO_ST_DATA(lsm6dso_data,
-				MOTIONSENSE_TYPE_GYRO),
-		.int_signal = GPIO_EC_IMU_INT_R_L,
-		.flags = MOTIONSENSE_FLAG_INT_SIGNAL,
-		.port = I2C_PORT_SENSOR,
-		.i2c_spi_addr_flags = LSM6DSO_ADDR0_FLAGS,
-		.default_range = 1000 | ROUND_UP_FLAG, /* dps */
-		.rot_standard_ref = &base_standard_ref,
-		.min_frequency = LSM6DSO_ODR_MIN_VAL,
-		.max_frequency = LSM6DSO_ODR_MAX_VAL,
-		.config = {
-			[SENSOR_CONFIG_EC_S0] = {
-				.odr = 13000 | ROUND_UP_FLAG,
-				.ec_rate = 100 * MSEC,
-			},
-			[SENSOR_CONFIG_EC_S3] = {
-				.odr = 10000 | ROUND_UP_FLAG,
-				.ec_rate = 100 * MSEC,
-			},
-		},
-	},
-
-	[CLEAR_ALS] = {
-		.name = "Clear Light",
-		.active_mask = SENSOR_ACTIVE_S0_S3,
-		.chip = MOTIONSENSE_CHIP_TCS3400,
-		.type = MOTIONSENSE_TYPE_LIGHT,
-		.location = MOTIONSENSE_LOC_CAMERA,
-		.drv = &tcs3400_drv,
-		.drv_data = &g_tcs3400_data,
-		.port = I2C_PORT_SENSOR,
-		.i2c_spi_addr_flags = TCS3400_I2C_ADDR_FLAGS,
-		.rot_standard_ref = NULL,
-		.default_range = 0x10000, /* scale = 1x, uscale = 0 */
-		.min_frequency = TCS3400_LIGHT_MIN_FREQ,
-		.max_frequency = TCS3400_LIGHT_MAX_FREQ,
-		.config = {
-			/* Run ALS sensor in S0 */
-			[SENSOR_CONFIG_EC_S0] = {
-				.odr = 1000,
-			},
-		},
-	},
-
-	[RGB_ALS] = {
-		/*
-		 * RGB channels read by CLEAR_ALS and so the i2c port and
-		 * address do not need to be defined for RGB_ALS.
-		 */
-		.name = "RGB Light",
-		.active_mask = SENSOR_ACTIVE_S0_S3,
-		.chip = MOTIONSENSE_CHIP_TCS3400,
-		.type = MOTIONSENSE_TYPE_LIGHT_RGB,
-		.location = MOTIONSENSE_LOC_CAMERA,
-		.drv = &tcs3400_rgb_drv,
-		.drv_data = &g_tcs3400_rgb_data,
-		.rot_standard_ref = NULL,
-		.default_range = 0x10000, /* scale = 1x, uscale = 0 */
-	},
-};
-const unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors);
-
-/* ALS instances when LPC mapping is needed. Each entry directs to a sensor. */
-const struct motion_sensor_t *motion_als_sensors[] = {
-	&motion_sensors[CLEAR_ALS],
-};
-BUILD_ASSERT(ARRAY_SIZE(motion_als_sensors) == ALS_COUNT);
-
-static void baseboard_sensors_init(void)
-{
-	/* Enable gpio interrupt for lid accel sensor */
-	gpio_enable_interrupt(GPIO_EC_ACCEL_INT_R_L);
-	/* Enable interrupt for the TCS3400 color light sensor */
-	gpio_enable_interrupt(GPIO_EC_ALS_RGB_INT_R_L);
-	/* Enable gpio interrupt for base accelgyro sensor */
-	gpio_enable_interrupt(GPIO_EC_IMU_INT_R_L);
-}
-DECLARE_HOOK(HOOK_INIT, baseboard_sensors_init, HOOK_PRIO_INIT_I2C + 1);
+BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT);
 
 /* Temperature sensor configuration */
 const struct temp_sensor_t temp_sensors[] = {
diff --git a/board/brask/tune_mp2964.c b/board/brask/tune_mp2964.c
deleted file mode 100644
index 198f06d8eb..0000000000
--- a/board/brask/tune_mp2964.c
+++ /dev/null
@@ -1,43 +0,0 @@
-/* Copyright 2021 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Tune the MP2964 IMVP9.1 parameters for brya */
-
-#include "common.h"
-#include "compile_time_macros.h"
-#include "console.h"
-#include "hooks.h"
-#include "mp2964.h"
-
-const static struct mp2964_reg_val rail_a[] = {
-	{ MP2964_MFR_ALT_SET,     0xe081 },	/* ALERT_DELAY = 200ns */
-};
-const static struct mp2964_reg_val rail_b[] = {
-	{ MP2964_MFR_ALT_SET,     0xe081 },	/* ALERT_DELAY = 200ns */
-};
-
-static void mp2964_on_startup(void)
-{
-	static int chip_updated;
-	int status;
-
-	if (get_board_id() != 1)
-		return;
-
-	if (chip_updated)
-		return;
-
-	chip_updated = 1;
-
-	ccprintf("%s: attempting to tune PMIC\n", __func__);
-
-	status = mp2964_tune(rail_a, ARRAY_SIZE(rail_a),
-			     rail_b, ARRAY_SIZE(rail_b));
-	if (status != EC_SUCCESS)
-		ccprintf("%s: could not update all settings\n", __func__);
-}
-
-DECLARE_HOOK(HOOK_CHIPSET_STARTUP, mp2964_on_startup,
-	     HOOK_PRIO_FIRST);
diff --git a/board/brask/usbc_config.c b/board/brask/usbc_config.c
index 40476c3f4f..a89e06e7b6 100644
--- a/board/brask/usbc_config.c
+++ b/board/brask/usbc_config.c
@@ -216,15 +216,9 @@ __override int bb_retimer_power_enable(const struct usb_mux *me, bool enable)
 	enum ioex_signal rst_signal;
 
 	if (me->usb_port == USBC_PORT_C0) {
-		if (get_board_id() == 1)
-			rst_signal = IOEX_ID_1_USB_C0_RT_RST_ODL;
-		else
-			rst_signal = IOEX_USB_C0_RT_RST_ODL;
+		rst_signal = IOEX_USB_C0_RT_RST_ODL;
 	} else if (me->usb_port == USBC_PORT_C2) {
-		if (get_board_id() == 1)
-			rst_signal = IOEX_ID_1_USB_C2_RT_RST_ODL;
-		else
-			rst_signal = IOEX_USB_C2_RT_RST_ODL;
+		rst_signal = IOEX_USB_C2_RT_RST_ODL;
 	} else {
 		return EC_ERROR_INVAL;
 	}
@@ -247,20 +241,6 @@ __override int bb_retimer_power_enable(const struct usb_mux *me, bool enable)
 		 * which powers I2C controller within retimer
 		 */
 		msleep(1);
-		if (get_board_id() == 1) {
-			int val;
-
-			/*
-			 * Check if we were able to deassert
-			 * reset. Board ID 1 uses a GPIO that is
-			 * uncontrollable when a debug accessory is
-			 * connected.
-			 */
-			if (ioex_get_level(rst_signal, &val) != EC_SUCCESS)
-				return EC_ERROR_UNKNOWN;
-			if (val != 1)
-				return EC_ERROR_NOT_POWERED;
-		}
 	} else {
 		ioex_set_level(rst_signal, 0);
 		msleep(1);
@@ -286,10 +266,7 @@ void board_reset_pd_mcu(void)
 {
 	enum gpio_signal tcpc_rst;
 
-	if (get_board_id() == 1)
-		tcpc_rst = GPIO_ID_1_USB_C0_C2_TCPC_RST_ODL;
-	else
-		tcpc_rst = GPIO_USB_C0_C2_TCPC_RST_ODL;
+	tcpc_rst = GPIO_USB_C0_C2_TCPC_RST_ODL;
 
 	/*
 	 * TODO(b/179648104): figure out correct timing
@@ -335,13 +312,8 @@ static void board_tcpc_init(void)
 		 * C0/C2 TCPC, so they must be set up after the TCPC has
 		 * been taken out of reset.
 		 */
-		if (get_board_id() == 1) {
-			enable_ioex(IOEX_ID_1_C0_NCT38XX);
-			enable_ioex(IOEX_ID_1_C2_NCT38XX);
-		} else {
-			enable_ioex(IOEX_C0_NCT38XX);
-			enable_ioex(IOEX_C2_NCT38XX);
-		}
+		enable_ioex(IOEX_C0_NCT38XX);
+		enable_ioex(IOEX_C2_NCT38XX);
 	}
 
 	/* Enable PPC interrupts. */