palkia: Initial board

Clone the board setting from the helios and change the 'helios' to
palkia

BUG=b:147078849
BRANCH=firmware-hatch-12669.B
TEST=run on DUT

Change-Id: I986a0e69aa2b0022d50e85118034fd956fb06345
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/2035442
Reviewed-by: Jett Rink <jettrink@chromium.org>

1 files changed, 155 insertions, 0 deletions

diff --git a/board/palkia/board.h b/board/palkia/board.h
new file mode 100644
index 0000000000..9e22619888
--- /dev/null
+++ b/board/palkia/board.h
@@ -0,0 +1,155 @@
+/* Copyright 2020 The Chromium OS Authors. All rights reserved.
+ * Use of this source code is governed by a BSD-style license that can be
+ * found in the LICENSE file.
+ */
+
+/* Palkia board configuration */
+
+#ifndef __CROS_EC_BOARD_H
+#define __CROS_EC_BOARD_H
+
+/* Baseboard features */
+#include "baseboard.h"
+
+#define CONFIG_POWER_BUTTON
+#define CONFIG_KEYBOARD_BOARD_CONFIG
+#define CONFIG_KEYBOARD_PROTOCOL_8042
+#define CONFIG_LED_COMMON
+#define CONFIG_LED_POWER_LED
+#define CONFIG_LOW_POWER_IDLE
+
+#define CONFIG_HOSTCMD_ESPI
+
+#undef CONFIG_UART_TX_BUF_SIZE
+#define CONFIG_UART_TX_BUF_SIZE 4096
+
+/* Keyboard features */
+#define CONFIG_PWM_KBLIGHT
+
+/* Sensors */
+/* BMI160 Base accel/gyro */
+#define CONFIG_ACCEL_INTERRUPTS
+#define CONFIG_ACCELGYRO_BMI160
+#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
+	TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
+#define CONFIG_ACCELGYRO_BMI160_INT2_OUTPUT
+/* BMA253 Lid accel */
+#define CONFIG_ACCEL_BMA255
+#define CONFIG_ACCEL_FORCE_MODE_MASK (BIT(LID_ACCEL) | BIT(LID_ALS))
+#define CONFIG_LID_ANGLE
+#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
+#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
+#define CONFIG_LID_ANGLE_UPDATE
+#define CONFIG_GMR_TABLET_MODE
+#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L
+
+/* USB Type C and USB PD defines */
+#define CONFIG_USB_PD_COMM_LOCKED
+#define CONFIG_USB_PD_TCPM_PS8751
+#define BOARD_TCPC_C0_RESET_HOLD_DELAY PS8XXX_RESET_DELAY_MS
+#define BOARD_TCPC_C0_RESET_POST_DELAY 0
+#define BOARD_TCPC_C1_RESET_HOLD_DELAY PS8XXX_RESET_DELAY_MS
+#define BOARD_TCPC_C1_RESET_POST_DELAY 0
+#define GPIO_USB_C0_TCPC_RST GPIO_USB_C0_TCPC_RST_ODL
+#define GPIO_USB_C1_TCPC_RST GPIO_USB_C1_TCPC_RST_ODL
+
+/*
+ * Palkia' battery takes several seconds to come back out of its disconnect
+ * state (~4.2 seconds on the unit I have, so give it a little more for margin).
+ */
+#undef  CONFIG_POWER_BUTTON_INIT_TIMEOUT
+#define CONFIG_POWER_BUTTON_INIT_TIMEOUT 6
+
+/* BC 1.2 */
+#define CONFIG_BC12_DETECT_PI3USB9201
+
+/* Volume Button feature */
+#define CONFIG_VOLUME_BUTTONS
+#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL
+#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL
+
+/* Fan features */
+#define CONFIG_FANS 1
+#undef CONFIG_FAN_INIT_SPEED
+#define CONFIG_FAN_INIT_SPEED 50
+#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_EN_A_RAILS
+#define CONFIG_THERMISTOR
+#define CONFIG_THROTTLE_AP
+#define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B
+
+/* DPTF */
+#define CONFIG_DPTF_MULTI_PROFILE
+
+/*
+ * Macros for GPIO signals used in common code that don't match the
+ * schematic names. Signal names in gpio.inc match the schematic and are
+ * then redefined here to so it's more clear which signal is being used for
+ * which purpose.
+ */
+#define GPIO_PCH_RSMRST_L	GPIO_EC_PCH_RSMRST_L
+#define GPIO_PCH_SLP_S0_L	GPIO_SLP_S0_L
+#define GPIO_CPU_PROCHOT	GPIO_EC_PROCHOT_ODL
+#define GPIO_AC_PRESENT		GPIO_ACOK_OD
+#define GPIO_RSMRST_L_PGOOD	GPIO_PG_EC_RSMRST_L
+#define GPIO_PCH_SYS_PWROK	GPIO_EC_PCH_SYS_PWROK
+#define GPIO_PCH_SLP_S3_L	GPIO_SLP_S3_L
+#define GPIO_PCH_SLP_S4_L	GPIO_SLP_S4_L
+#define GPIO_EN_PP5000		GPIO_EN_PP5000_A
+
+#ifndef __ASSEMBLER__
+
+#include "gpio_signal.h"
+#include "registers.h"
+
+enum adc_channel {
+	ADC_TEMP_SENSOR_1,	/* ADC0 */
+	ADC_TEMP_SENSOR_2,	/* ADC1 */
+	ADC_TEMP_SENSOR_3,	/* ADC3 */
+	ADC_TEMP_SENSOR_4,	/* ADC2 */
+	ADC_CH_COUNT
+};
+
+enum sensor_id {
+	LID_ACCEL = 0,
+	BASE_ACCEL,
+	BASE_GYRO,
+	LID_ALS,
+	SENSOR_COUNT,
+};
+
+enum pwm_channel {
+	PWM_CH_KBLIGHT,
+	PWM_CH_FAN,
+	PWM_CH_COUNT
+};
+
+enum fan_channel {
+	FAN_CH_0 = 0,
+	/* Number of FAN channels */
+	FAN_CH_COUNT,
+};
+
+enum mft_channel {
+	MFT_CH_0 = 0,
+	/* Number of MFT channels */
+	MFT_CH_COUNT,
+};
+
+enum temp_sensor_id {
+	TEMP_SENSOR_1,
+	TEMP_SENSOR_2,
+	TEMP_SENSOR_3,
+	TEMP_SENSOR_4,
+	TEMP_SENSOR_COUNT
+};
+
+/* List of possible batteries */
+enum battery_type {
+	BATTERY_SIMPLO_C424,
+	BATTERY_SIMPLO_C436,
+	BATTERY_TYPE_COUNT,
+};
+
+#endif /* !__ASSEMBLER__ */
+
+#endif /* __CROS_EC_BOARD_H */