diff options
| -rw-r--r-- | board/boten/gpio.inc | 3 | ||||
| -rw-r--r-- | board/madoo/board.h | 3 | ||||
| -rw-r--r-- | board/magolor/board.h | 3 | ||||
| -rw-r--r-- | board/waddledee/board.h | 7 | ||||
| -rw-r--r-- | board/waddledoo/board.h | 8 |
5 files changed, 24 insertions, 0 deletions
diff --git a/board/boten/gpio.inc b/board/boten/gpio.inc index b73f53c091..bfca6fdc9c 100644 --- a/board/boten/gpio.inc +++ b/board/boten/gpio.inc @@ -66,6 +66,9 @@ UNIMPLEMENTED(AC_PRESENT) UNIMPLEMENTED(PG_EC_DSW_PWROK) UNIMPLEMENTED(PG_EC_ALL_SYS_PWRGD) +/* Used by baseboard z-state enable, but not present on boten */ +UNIMPLEMENTED(USB_C1_INT_ODL) + /* I2C pins - Alternate function below configures I2C module on these pins */ GPIO(EC_I2C_EEPROM_SCL, PIN(B, 3), GPIO_INPUT) GPIO(EC_I2C_EEPROM_SDA, PIN(B, 4), GPIO_INPUT) diff --git a/board/madoo/board.h b/board/madoo/board.h index 21558fdc3a..3d99e59627 100644 --- a/board/madoo/board.h +++ b/board/madoo/board.h @@ -29,6 +29,9 @@ #define CONFIG_CMD_TCPC_DUMP #define CONFIG_CMD_CHARGER_DUMP +/* GPIO for C1 interrupts, for baseboard use */ +#define GPIO_USB_C1_INT_ODL GPIO_SUB_USB_C1_INT_ODL + /* Keyboard */ #define CONFIG_PWM_KBLIGHT diff --git a/board/magolor/board.h b/board/magolor/board.h index e2d86922cb..a1d32f1bd4 100644 --- a/board/magolor/board.h +++ b/board/magolor/board.h @@ -32,6 +32,9 @@ #define CONFIG_CMD_TCPC_DUMP #define CONFIG_CMD_CHARGER_DUMP +/* GPIO for C1 interrupts, for baseboard use */ +#define GPIO_USB_C1_INT_ODL GPIO_SUB_USB_C1_INT_ODL + /* Keyboard */ #define CONFIG_PWM_KBLIGHT diff --git a/board/waddledee/board.h b/board/waddledee/board.h index c627316ac9..d4f585a707 100644 --- a/board/waddledee/board.h +++ b/board/waddledee/board.h @@ -32,6 +32,13 @@ #define CONFIG_OCPC #define CONFIG_OCPC_DEF_RBATT_MOHMS 5 /* R_DS(on) 5.3mOhm */ +/* + * GPIO for C1 interrupts, for baseboard use + * + * Note this will only be valid for board revision 1 + */ +#define GPIO_USB_C1_INT_ODL GPIO_USB_C1_INT_V1_ODL + /* LED */ #define CONFIG_LED_PWM #define CONFIG_LED_PWM_COUNT 1 diff --git a/board/waddledoo/board.h b/board/waddledoo/board.h index 98a4b2caca..dce01cf67c 100644 --- a/board/waddledoo/board.h +++ b/board/waddledoo/board.h @@ -32,6 +32,14 @@ #define CONFIG_CMD_TCPC_DUMP #define CONFIG_CMD_CHARGER_DUMP +/* + * GPIO for C1 interrupts, for baseboard use + * + * Note this line might already have its pull up disabled for HDMI DBs, but + * it should be fine to set again before z-state. + */ +#define GPIO_USB_C1_INT_ODL GPIO_SUB_C1_INT_EN_RAILS_ODL + /* Keyboard */ #define CONFIG_PWM_KBLIGHT |