diff options
-rw-r--r-- | board/lindar/board.c | 142 | ||||
-rw-r--r-- | board/lindar/board.h | 30 | ||||
-rw-r--r-- | board/lindar/ec.tasklist | 1 | ||||
-rw-r--r-- | board/lindar/gpio.inc | 16 |
4 files changed, 179 insertions, 10 deletions
diff --git a/board/lindar/board.c b/board/lindar/board.c index a4e685a837..ce30e301c9 100644 --- a/board/lindar/board.c +++ b/board/lindar/board.c @@ -8,6 +8,8 @@ #include "button.h" #include "cbi_ec_fw_config.h" #include "common.h" +#include "driver/accel_lis2dh.h" +#include "driver/accelgyro_lsm6dsm.h" #include "driver/bc12/pi3usb9201.h" #include "driver/ppc/sn5s330.h" #include "driver/ppc/syv682x.h" @@ -68,6 +70,17 @@ union volteer_cbi_fw_config fw_config_defaults = { static void board_init(void) { + if (ec_cfg_has_tabletmode()) { + /* Enable gpio interrupt for base accelgyro sensor */ + gpio_enable_interrupt(GPIO_EC_IMU_INT_L); + } else { + motion_sensor_count = 0; + /* Device is clamshell only */ + tablet_set_mode(0); + /* Gyro is not present, don't allow line to float */ + gpio_set_flags(GPIO_EC_IMU_INT_L, GPIO_INPUT | GPIO_PULL_DOWN); + } + /* * TODO: b/154447182 - Malefor will control power LED and battery LED * independently, and keep the max brightness of power LED and battery @@ -78,6 +91,128 @@ static void board_init(void) } DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT); +int board_is_lid_angle_tablet_mode(void) +{ + return ec_cfg_has_tabletmode(); +} + +/* Enable or disable input devices, based on tablet mode or chipset state */ +#ifndef TEST_BUILD +void lid_angle_peripheral_enable(int enable) +{ + if (ec_cfg_has_tabletmode()) { + if (chipset_in_state(CHIPSET_STATE_ANY_OFF) || + tablet_get_mode()) + enable = 0; + keyboard_scan_enable(enable, KB_SCAN_DISABLE_LID_ANGLE); + } +} +#endif + +/******************************************************************************/ +/* Sensors */ +/* Lid and base Sensor mutex */ +static struct mutex g_lid_accel_mutex; +static struct mutex g_base_mutex; + +/* Lid and base accel private data */ +static struct stprivate_data g_lis2dh_data; +static struct lsm6dsm_data lsm6dsm_data = LSM6DSM_DATA; + +/* Matrix to rotate lid and base sensor into standard reference frame */ +static const mat33_fp_t lid_standard_ref = { + { 0, FLOAT_TO_FP(1), 0}, + { FLOAT_TO_FP(1), 0, 0}, + { 0, 0, FLOAT_TO_FP(-1)} +}; + +static const mat33_fp_t base_standard_ref = { + { FLOAT_TO_FP(1), 0, 0}, + { 0, FLOAT_TO_FP(-1), 0}, + { 0, 0, FLOAT_TO_FP(-1)} +}; + +struct motion_sensor_t motion_sensors[] = { + [LID_ACCEL] = { + .name = "Lid Accel", + .active_mask = SENSOR_ACTIVE_S0_S3, + .chip = MOTIONSENSE_CHIP_LIS2DE, + .type = MOTIONSENSE_TYPE_ACCEL, + .location = MOTIONSENSE_LOC_LID, + .drv = &lis2dh_drv, + .mutex = &g_lid_accel_mutex, + .drv_data = &g_lis2dh_data, + .port = I2C_PORT_SENSOR, + .i2c_spi_addr_flags = LIS2DH_ADDR1_FLAGS, + .rot_standard_ref = &lid_standard_ref, + .min_frequency = LIS2DH_ODR_MIN_VAL, + .max_frequency = LIS2DH_ODR_MAX_VAL, + .default_range = 2, /* g, to support tablet mode */ + .config = { + /* EC use accel for angle detection */ + [SENSOR_CONFIG_EC_S0] = { + .odr = 10000 | ROUND_UP_FLAG, + }, + /* Sensor on in S3 */ + [SENSOR_CONFIG_EC_S3] = { + .odr = 10000 | ROUND_UP_FLAG, + }, + }, + }, + + [BASE_ACCEL] = { + .name = "Base Accel", + .active_mask = SENSOR_ACTIVE_S0_S3, + .chip = MOTIONSENSE_CHIP_LSM6DSM, + .type = MOTIONSENSE_TYPE_ACCEL, + .location = MOTIONSENSE_LOC_BASE, + .drv = &lsm6dsm_drv, + .mutex = &g_base_mutex, + .drv_data = LSM6DSM_ST_DATA(lsm6dsm_data, + MOTIONSENSE_TYPE_ACCEL), + .int_signal = GPIO_EC_IMU_INT_L, + .flags = MOTIONSENSE_FLAG_INT_SIGNAL, + .port = I2C_PORT_SENSOR, + .i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS, + .rot_standard_ref = &base_standard_ref, + .default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs */ + .min_frequency = LSM6DSM_ODR_MIN_VAL, + .max_frequency = LSM6DSM_ODR_MAX_VAL, + .config = { + /* EC use accel for angle detection */ + [SENSOR_CONFIG_EC_S0] = { + .odr = 13000 | ROUND_UP_FLAG, + .ec_rate = 100 * MSEC, + }, + /* Sensor on for angle detection */ + [SENSOR_CONFIG_EC_S3] = { + .odr = 10000 | ROUND_UP_FLAG, + .ec_rate = 100 * MSEC, + }, + }, + }, + + [BASE_GYRO] = { + .name = "Base Gyro", + .active_mask = SENSOR_ACTIVE_S0_S3, + .chip = MOTIONSENSE_CHIP_LSM6DSM, + .type = MOTIONSENSE_TYPE_GYRO, + .location = MOTIONSENSE_LOC_BASE, + .drv = &lsm6dsm_drv, + .mutex = &g_base_mutex, + .drv_data = LSM6DSM_ST_DATA(lsm6dsm_data, + MOTIONSENSE_TYPE_GYRO), + .int_signal = GPIO_EC_IMU_INT_L, + .flags = MOTIONSENSE_FLAG_INT_SIGNAL, + .port = I2C_PORT_SENSOR, + .i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS, + .default_range = 1000 | ROUND_UP_FLAG, /* dps */ + .rot_standard_ref = &base_standard_ref, + .min_frequency = LSM6DSM_ODR_MIN_VAL, + .max_frequency = LSM6DSM_ODR_MAX_VAL, + }, +}; +unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors); /******************************************************************************/ /* Physical fans. These are logically separate from pwm_channels. */ @@ -176,6 +311,13 @@ BUILD_ASSERT(ARRAY_SIZE(mft_channels) == MFT_CH_COUNT); /* I2C port map configuration */ const struct i2c_port_t i2c_ports[] = { { + .name = "sensor", + .port = I2C_PORT_SENSOR, + .kbps = 400, + .scl = GPIO_EC_I2C0_SENSOR_SCL, + .sda = GPIO_EC_I2C0_SENSOR_SDA, + }, + { .name = "usb_c0", .port = I2C_PORT_USB_C0, .kbps = 1000, diff --git a/board/lindar/board.h b/board/lindar/board.h index 151b300ff1..bacac9d015 100644 --- a/board/lindar/board.h +++ b/board/lindar/board.h @@ -25,10 +25,22 @@ /* Keyboard features */ -/* Sensors not supported*/ -#undef CONFIG_ACCEL_FIFO -#undef CONFIG_TABLET_MODE -#undef CONFIG_MKBP_EVENT +/* Sensors */ +#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT +#define CONFIG_ACCEL_LIS2DE /* Lid accel */ +#define CONFIG_ACCELGYRO_LSM6DSM /* Base accel */ + +/* Sensors without hardware FIFO are in forced mode */ +#define CONFIG_ACCEL_FORCE_MODE_MASK \ + BIT(LID_ACCEL) + +#define CONFIG_LID_ANGLE +#define CONFIG_LID_ANGLE_UPDATE +#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL +#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL + +#define CONFIG_ACCEL_LSM6DSM_INT_EVENT \ + TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) /* USB Type C and USB PD defines */ #define CONFIG_USB_PD_PORT_MAX_COUNT 2 @@ -82,6 +94,7 @@ * which purpose. */ #define GPIO_AC_PRESENT GPIO_ACOK_OD +#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL #define GPIO_EN_PP5000 GPIO_EN_PP5000_A #define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW #define GPIO_LID_OPEN GPIO_EC_LID_OPEN @@ -102,9 +115,11 @@ #define GPIO_USB_C1_BC12_INT_ODL GPIO_USB_C1_MIX_INT_ODL #define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL #define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_MUTE_BTN_ODL +#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L /* I2C Bus Configuration */ #define CONFIG_I2C +#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 #define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0 #define I2C_PORT_USB_C1 NPCX_I2C_PORT2_0 #define I2C_PORT_LIGHTBAR NPCX_I2C_PORT3_0 @@ -137,6 +152,13 @@ enum pwm_channel { PWM_CH_COUNT }; +enum sensor_id { + LID_ACCEL = 0, + BASE_ACCEL, + BASE_GYRO, + SENSOR_COUNT, +}; + enum usbc_port { USBC_PORT_C0 = 0, USBC_PORT_C1, diff --git a/board/lindar/ec.tasklist b/board/lindar/ec.tasklist index 2c9a9e8e32..292de51cdb 100644 --- a/board/lindar/ec.tasklist +++ b/board/lindar/ec.tasklist @@ -13,6 +13,7 @@ TASK_ALWAYS(USB_CHG_P0, usb_charger_task, 0, TASK_STACK_SIZE) \ TASK_ALWAYS(USB_CHG_P1, usb_charger_task, 0, TASK_STACK_SIZE) \ TASK_ALWAYS(CHARGER, charger_task, NULL, VENTI_TASK_STACK_SIZE) \ + TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \ TASK_NOTEST(KEYPROTO, keyboard_protocol_task, NULL, TASK_STACK_SIZE) \ TASK_NOTEST(CHIPSET, chipset_task, NULL, LARGER_TASK_STACK_SIZE) \ TASK_ALWAYS(HOSTCMD, host_command_task, NULL, LARGER_TASK_STACK_SIZE) \ diff --git a/board/lindar/gpio.inc b/board/lindar/gpio.inc index 4c3bce9696..611512a7b6 100644 --- a/board/lindar/gpio.inc +++ b/board/lindar/gpio.inc @@ -24,6 +24,11 @@ GPIO_INT(PG_EC_RSMRST_ODL, PIN(E, 2), GPIO_INT_BOTH, power_signal_interrupt) GPIO_INT(PG_EC_DSW_PWROK, PIN(C, 7), GPIO_INT_BOTH, power_signal_interrupt) GPIO_INT(PG_EC_ALL_SYS_PWRGD, PIN(F, 4), GPIO_INT_BOTH, power_signal_interrupt) +/* Sensor Interrupts */ +GPIO_INT(EC_IMU_INT_L, PIN(5, 6), GPIO_INT_FALLING | GPIO_SEL_1P8V, lsm6dsm_interrupt) +GPIO(EC_ACCEL_INT_L, PIN(8, 1), GPIO_INPUT | GPIO_SEL_1P8V) +GPIO_INT(TABLET_MODE_L, PIN(9, 5), GPIO_INT_BOTH, gmr_tablet_switch_isr) + /* USB-C interrupts */ GPIO_INT(USB_C0_TCPC_INT_ODL, PIN(E, 0), GPIO_INT_BOTH, tcpc_alert_event) GPIO_INT(USB_C1_TCPC_INT_ODL, PIN(A, 2), GPIO_INT_BOTH, tcpc_alert_event) @@ -75,6 +80,8 @@ GPIO(EC_PROCHOT_ODL, PIN(6, 3), GPIO_ODR_HIGH) UNIMPLEMENTED(EC_PROCHOT_IN_L) GPIO(SYS_RST_ODL, PIN(C, 5), GPIO_ODR_HIGH) +GPIO(EC_PCH_INT_ODL, PIN(B, 0), GPIO_ODR_HIGH) + /* USB and USBC Signals */ GPIO(USB_C1_RT_RST_ODL, PIN(8, 3), GPIO_ODR_LOW) /* USB_C1 Reset on boards board ID >=1 */ GPIO(USB_C0_OC_ODL, PIN(B, 1), GPIO_ODR_HIGH) @@ -101,6 +108,8 @@ GPIO(M2_SSD_PLA, PIN(7, 0), GPIO_INPUT) /* SSD power-loss acknoledgement */ GPIO(EC_EDP_BL_EN, PIN(D, 3), GPIO_OUT_HIGH) /* I2C pins - Alternate function below configures I2C module on these pins */ +GPIO(EC_I2C0_SENSOR_SCL, PIN(B, 5), GPIO_INPUT | GPIO_SEL_1P8V) +GPIO(EC_I2C0_SENSOR_SDA, PIN(B, 4), GPIO_INPUT | GPIO_SEL_1P8V) GPIO(EC_I2C1_USB_C0_SCL, PIN(9, 0), GPIO_INPUT) GPIO(EC_I2C1_USB_C0_SDA, PIN(8, 7), GPIO_INPUT) GPIO(EC_I2C2_USB_C1_SCL, PIN(9, 2), GPIO_INPUT) @@ -121,6 +130,7 @@ GPIO(LED_2_L, PIN(C, 3), GPIO_OUT_HIGH) /* Battery - Red LED */ GPIO(LED_3_L, PIN(C, 2), GPIO_OUT_HIGH) /* Power - White LED */ /* Alternate functions GPIO definitions */ +ALTERNATE(PIN_MASK(B, BIT(5) | BIT(4)), 0, MODULE_I2C, (GPIO_INPUT | GPIO_SEL_1P8V)) /* I2C0 */ ALTERNATE(PIN_MASK(9, BIT(0) | BIT(2) | BIT(1)), 0, MODULE_I2C, 0) /* I2C1 SCL / I2C2 */ ALTERNATE(PIN_MASK(8, BIT(7)), 0, MODULE_I2C, 0) /* I2C1 SDA */ ALTERNATE(PIN_MASK(D, BIT(1) | BIT(0)), 0, MODULE_I2C, 0) /* I2C3 */ @@ -153,14 +163,8 @@ ALTERNATE(PIN_MASK(0, BIT(0) | BIT(1) | BIT(2)), 0, MODULE_PMU, 0) /* GPIO00 = GPIO02 = EC_RST_ODL */ /* Unused signals */ -GPIO(UNUSED_GPIO81, PIN(8, 1), GPIO_INPUT | GPIO_PULL_UP) -GPIO(UNUSED_GPIOB5, PIN(B, 5), GPIO_INPUT | GPIO_PULL_UP) -GPIO(UNUSED_GPIOB4, PIN(B, 4), GPIO_INPUT | GPIO_PULL_UP) GPIO(UNUSED_GPIO60, PIN(6, 0), GPIO_INPUT | GPIO_PULL_UP) GPIO(UNUSED_GPIO34, PIN(3, 4), GPIO_INPUT | GPIO_PULL_UP) GPIO(UNUSED_GPIO96, PIN(9, 6), GPIO_INPUT | GPIO_PULL_UP) GPIO(UNUSED_GPIOF2, PIN(F, 2), GPIO_INPUT | GPIO_PULL_UP) GPIO(UNUSED_GPIOF3, PIN(F, 3), GPIO_INPUT | GPIO_PULL_UP) -GPIO(UNUSED_GPIO56, PIN(5, 6), GPIO_INPUT | GPIO_PULL_UP) -GPIO(UNUSED_GPIO95, PIN(9, 5), GPIO_INPUT | GPIO_PULL_UP) -GPIO(UNUSED_GPIOB0, PIN(B, 0), GPIO_INPUT | GPIO_PULL_UP) |