1 files changed, 0 insertions, 92 deletions
diff --git a/baseboard/dragonegg/battery.c b/baseboard/dragonegg/battery.c
deleted file mode 100644
index 0c4ec32903..0000000000
--- a/baseboard/dragonegg/battery.c
+++ /dev/null
@@ -1,92 +0,0 @@
-/* Copyright 2018 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- *
- * Battery pack vendor provided charging profile
- */
-
-#include "battery.h"
-#include "battery_fuel_gauge.h"
-#include "battery_smart.h"
-#include "gpio.h"
-#include "system.h"
-
-static enum battery_present batt_pres_prev = BP_NOT_SURE;
-
-enum battery_present battery_hw_present(void)
-{
-	enum battery_present bp;
-	/* The GPIO is low when the battery is physically present */
-	/*
-	 * TODO(b/111704193): The signal GPIO_EC_BATT_PRES_ODL has an issue
-	 * where it's floating (?) at ~2V when it should be low when the battery
-	 * is connected. The signal will read correctly following a cold reset
-	 * and the battery is connected, but following a warm reboot, it reads
-	 * high. In order to allow charging to work, replacing this with the a
-	 * check that the Operation Status register can be read. Once the HW
-	 * issue is resolved then change this back to checking the physical
-	 * presence pin.
-	 *
-	 */
-
-	if (system_get_board_version() == 0)
-		/* P0 boards can't use gpio signal */
-		bp = (battery_get_disconnect_state() ==
-		      BATTERY_DISCONNECT_ERROR) ? BP_NO : BP_YES;
-	else
-		/* P1 boards can read presence from gpio signal */
-		bp = gpio_get_level(GPIO_EC_BATT_PRES_ODL) ? BP_NO : BP_YES;
-
-	return bp;
-}
-
-static int battery_init(void)
-{
-	int batt_status;
-
-	return battery_status(&batt_status) ? 0 :
-		!!(batt_status & STATUS_INITIALIZED);
-}
-
-/*
- * Physical detection of battery.
- */
-static enum battery_present battery_check_present_status(void)
-{
-	enum battery_present batt_pres;
-
-	/* Get the physical hardware status */
-	batt_pres = battery_hw_present();
-
-	/*
-	 * If the battery is not physically connected, then no need to perform
-	 * any more checks.
-	 */
-	if (batt_pres != BP_YES)
-		return batt_pres;
-
-	/*
-	 * If the battery is present now and was present last time we checked,
-	 * return early.
-	 */
-	if (batt_pres == batt_pres_prev)
-		return batt_pres;
-
-	/*
-	 * Ensure that battery is:
-	 * 1. Not in cutoff
-	 * 2. Initialized
-	 */
-	if (battery_is_cut_off() != BATTERY_CUTOFF_STATE_NORMAL ||
-	    battery_init() == 0) {
-		batt_pres = BP_NO;
-	}
-
-	return batt_pres;
-}
-
-enum battery_present battery_is_present(void)
-{
-	batt_pres_prev = battery_check_present_status();
-	return batt_pres_prev;
-}