1 files changed, 197 insertions, 0 deletions
diff --git a/baseboard/ite_evb/baseboard.c b/baseboard/ite_evb/baseboard.c
new file mode 100644
index 0000000000..0bd537ef4f
--- /dev/null
+++ b/baseboard/ite_evb/baseboard.c
@@ -0,0 +1,197 @@
+/* Copyright 2020 The Chromium OS Authors. All rights reserved.
+ * Use of this source code is governed by a BSD-style license that can be
+ * found in the LICENSE file.
+ */
+
+/* ite_evb baseboard configuration */
+#include "clock.h"
+#include "common.h"
+#include "console.h"
+#include "fan.h"
+#include "gpio.h"
+#include "hooks.h"
+#include "i2c.h"
+#include "intc.h"
+#include "keyboard_scan.h"
+#include "lid_switch.h"
+#include "lpc.h"
+#include "power_button.h"
+#include "pwm_chip.h"
+#include "registers.h"
+#include "spi.h"
+#include "switch.h"
+#include "system.h"
+#include "task.h"
+#include "timer.h"
+#include "uart.h"
+#include "util.h"
+#include "gpio_list.h"
+
+#if defined(CONFIG_FANS) || defined(CONFIG_PWM)
+const struct fan_conf fan_conf_0 = {
+	.flags = FAN_USE_RPM_MODE,
+	.ch = 0, /* Use MFT id to control fan */
+	.pgood_gpio = -1,
+	.enable_gpio = -1,
+};
+
+const struct fan_rpm fan_rpm_0 = {
+	.rpm_min = 1500,
+	.rpm_start = 1500,
+	.rpm_max = 6500,
+};
+
+const struct fan_t fans[] = {
+	{ .conf = &fan_conf_0,
+	  .rpm = &fan_rpm_0, },
+};
+BUILD_ASSERT(ARRAY_SIZE(fans) == CONFIG_FANS);
+
+/*
+ * PWM HW channelx binding tachometer channelx for fan control.
+ * Four tachometer input pins but two tachometer modules only,
+ * so always binding [TACH_CH_TACH0A | TACH_CH_TACH0B] and/or
+ * [TACH_CH_TACH1A | TACH_CH_TACH1B]
+ */
+const struct fan_tach_t fan_tach[] = {
+	[PWM_HW_CH_DCR0] = {
+		.ch_tach = TACH_CH_NULL,
+		.fan_p = -1,
+		.rpm_re = -1,
+		.s_duty = -1,
+	},
+	[PWM_HW_CH_DCR1] = {
+		.ch_tach = TACH_CH_NULL,
+		.fan_p = -1,
+		.rpm_re = -1,
+		.s_duty = -1,
+	},
+	[PWM_HW_CH_DCR2] = {
+		.ch_tach = TACH_CH_TACH1A,
+		.fan_p = -1,
+		.rpm_re = -1,
+		.s_duty = -1,
+	},
+	[PWM_HW_CH_DCR3] = {
+		.ch_tach = TACH_CH_NULL,
+		.fan_p = -1,
+		.rpm_re = -1,
+		.s_duty = -1,
+	},
+	[PWM_HW_CH_DCR4] = {
+		.ch_tach = TACH_CH_NULL,
+		.fan_p = -1,
+		.rpm_re = -1,
+		.s_duty = -1,
+	},
+	[PWM_HW_CH_DCR5] = {
+		.ch_tach = TACH_CH_NULL,
+		.fan_p = -1,
+		.rpm_re = -1,
+		.s_duty = -1,
+	},
+	[PWM_HW_CH_DCR6] = {
+		.ch_tach = TACH_CH_NULL,
+		.fan_p = -1,
+		.rpm_re = -1,
+		.s_duty = -1,
+	},
+	[PWM_HW_CH_DCR7] = {
+		.ch_tach = TACH_CH_TACH0A,
+		.fan_p = 2,
+		.rpm_re = 50,
+		.s_duty = 30,
+	},
+};
+BUILD_ASSERT(ARRAY_SIZE(fan_tach) == PWM_HW_CH_TOTAL);
+#endif /* defined(CONFIG_FANS) || defined(CONFIG_PWM) */
+
+#if defined(CONFIG_KEYBOARD_BOARD_CONFIG)
+/* Keyboard scan setting */
+struct keyboard_scan_config keyscan_config = {
+	.output_settle_us = 35,
+	.debounce_down_us = 5 * MSEC,
+	.debounce_up_us = 40 * MSEC,
+	.scan_period_us = 3 * MSEC,
+	.min_post_scan_delay_us = 1000,
+	.poll_timeout_us = 100 * MSEC,
+	.actual_key_mask = {
+		0x14, 0xff, 0xff, 0xff, 0xff, 0xf5, 0xff,
+		0xa4, 0xff, 0xfe, 0x55, 0xfa, 0xca  /* full set */
+	},
+};
+#endif
+
+#if defined(CONFIG_SPI_FLASH_PORT)
+/* SPI devices */
+const struct spi_device_t spi_devices[] = {
+	[CONFIG_SPI_FLASH_PORT] = {
+		.port = CONFIG_SPI_FLASH_PORT,
+		.div = 0,
+		.gpio_cs = -1
+	},
+};
+const unsigned int spi_devices_used = ARRAY_SIZE(spi_devices);
+#endif
+
+/* Initialize board. */
+static void board_init(void)
+{
+}
+DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT);
+
+/* Wake-up pins for hibernate */
+const enum gpio_signal hibernate_wake_pins[] = {
+	GPIO_POWER_BUTTON_L, GPIO_LID_OPEN
+};
+const int hibernate_wake_pins_used = ARRAY_SIZE(hibernate_wake_pins);
+
+/*
+ * I2C channels (A, B, and C) are using the same timing registers (00h~07h)
+ * at default.
+ * In order to set frequency independently for each channels,
+ * We use timing registers 09h~0Bh, and the supported frequency will be:
+ * 50KHz, 100KHz, 400KHz, or 1MHz.
+ * I2C channels (D, E and F) can be set different frequency on different ports.
+ * The I2C(D/E/F) frequency depend on the frequency of SMBus Module and
+ * the individual prescale register.
+ * The frequency of SMBus module is 24MHz on default.
+ * The allowed range of I2C(D/E/F) frequency is as following setting.
+ * SMBus Module Freq = PLL_CLOCK / ((IT83XX_ECPM_SCDCR2 & 0x0F) + 1)
+ * (SMBus Module Freq / 510) <=  I2C Freq <= (SMBus Module Freq / 8)
+ * Channel D has multi-function and can be used as UART interface.
+ * Channel F is reserved for EC debug.
+ */
+
+/* I2C ports */
+const struct i2c_port_t i2c_ports[] = {
+	{
+		.name = "battery",
+		.port = I2C_PORT_BATTERY,
+		.kbps = 100,
+		.scl = GPIO_I2C_C_SCL,
+		.sda = GPIO_I2C_C_SDA,
+	},
+	{
+		.name = "evb-1",
+		.port = IT83XX_I2C_CH_A,
+		.kbps = 100,
+		.scl = GPIO_I2C_A_SCL,
+		.sda = GPIO_I2C_A_SDA,
+	},
+	{
+		.name = "evb-2",
+		.port = IT83XX_I2C_CH_B,
+		.kbps = 100,
+		.scl = GPIO_I2C_B_SCL,
+		.sda = GPIO_I2C_B_SDA,
+	},
+	{
+		.name = "opt-4",
+		.port = IT83XX_I2C_CH_E,
+		.kbps = 100,
+		.scl = GPIO_I2C_E_SCL,
+		.sda = GPIO_I2C_E_SDA,
+	},
+};
+const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports);