diff options
Diffstat (limited to 'baseboard/trogdor/baseboard.h')
| -rw-r--r-- | baseboard/trogdor/baseboard.h | 196 |
1 files changed, 196 insertions, 0 deletions
diff --git a/baseboard/trogdor/baseboard.h b/baseboard/trogdor/baseboard.h new file mode 100644 index 0000000000..f1ad825e5c --- /dev/null +++ b/baseboard/trogdor/baseboard.h @@ -0,0 +1,196 @@ +/* Copyright 2020 The Chromium OS Authors. All rights reserved. + * Use of this source code is governed by a BSD-style license that can be + * found in the LICENSE file. + */ + +/* Trogdor baseboard configuration */ + +#ifndef __CROS_EC_BASEBOARD_H +#define __CROS_EC_BASEBOARD_H + +/* + * By default, enable all console messages excepted event and HC: + * The sensor stack is generating a lot of activity. + * They can be enabled through the console command 'chan'. + */ +#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_HOSTCMD))) + +/* NPCX7 config */ +#define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */ +#define NPCX_TACH_SEL2 0 /* No tach. */ +#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */ + +/* Internal SPI flash on NPCX7 */ +#define CONFIG_SPI_FLASH_REGS +#define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */ +#define CONFIG_HOSTCMD_FLASH_SPI_INFO + +/* EC Modules */ +#define CONFIG_I2C +#define CONFIG_I2C_MASTER +#define CONFIG_LED_COMMON +#define CONFIG_LOW_POWER_IDLE +#define CONFIG_ADC +#define CONFIG_BACKLIGHT_LID +#define CONFIG_FPU +#define CONFIG_PWM +#define CONFIG_PWM_DISPLIGHT +#define CONFIG_PWM_KBLIGHT + +#define CONFIG_VBOOT_HASH + +#undef CONFIG_PECI + +#define CONFIG_HOSTCMD_SPS +#define CONFIG_HOST_COMMAND_STATUS +#define CONFIG_HOSTCMD_SECTION_SORTED +#define CONFIG_MKBP_EVENT +#define CONFIG_KEYBOARD_PROTOCOL_MKBP +#define CONFIG_KEYBOARD_COL2_INVERTED +#define CONFIG_MKBP_USE_GPIO + +#define CONFIG_BOARD_VERSION_GPIO +#define CONFIG_POWER_BUTTON +#define CONFIG_VOLUME_BUTTONS +#define CONFIG_EMULATED_SYSRQ +#define CONFIG_CMD_BUTTON +#define CONFIG_SWITCH +#define CONFIG_LID_SWITCH +#define CONFIG_EXTPOWER_GPIO + +/* Battery */ +#define CONFIG_BATTERY_CUT_OFF +#define CONFIG_BATTERY_PRESENT_GPIO GPIO_BATT_PRES_ODL +#define CONFIG_BATTERY_SMART + +/* Charger */ +#define CONFIG_CHARGER +#define CONFIG_CHARGE_MANAGER +#define CONFIG_CHARGER_ISL9238 +#define CONFIG_CHARGE_RAMP_HW +#define CONFIG_USB_CHARGER +#define CONFIG_CMD_CHARGER_ADC_AMON_BMON +#define CONFIG_CHARGER_PSYS +#define CONFIG_CHARGER_PSYS_READ +#define CONFIG_CHARGER_DISCHARGE_ON_AC + +#define CONFIG_CHARGER_INPUT_CURRENT 512 +#define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 2 +#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON 7500 +#define CONFIG_CHARGER_SENSE_RESISTOR 10 +#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 + +/* + * USB ID + * + * This is allocated specifically for Trogdor + * http://google3/hardware/standards/usb/ + */ +#define CONFIG_USB_PID 0x5043 + +/* USB */ +#define CONFIG_USB_POWER_DELIVERY +#define CONFIG_USB_PD_TCPMV2 +#define CONFIG_USB_DRP_ACC_TRYSRC +#define CONFIG_USB_PD_DECODE_SOP +#define CONFIG_CMD_PD_CONTROL +#define CONFIG_USB_PD_ALT_MODE +#define CONFIG_USB_PD_ALT_MODE_DFP +#define CONFIG_USB_PD_DISCHARGE_PPC +#define CONFIG_USB_PD_DUAL_ROLE +#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE +#define CONFIG_USB_PD_TCPC_LOW_POWER +#define CONFIG_USB_PD_LOGGING +#define CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT TYPEC_RP_3A0 +#define CONFIG_USB_PD_PORT_MAX_COUNT 2 +#define CONFIG_USB_PD_TCPM_MUX +#define CONFIG_USB_PD_TCPM_TCPCI +#define CONFIG_USB_PD_TRY_SRC +#define CONFIG_USB_PD_VBUS_DETECT_TCPC +#define CONFIG_USB_PD_5V_EN_CUSTOM +#define CONFIG_USBC_SS_MUX +#define CONFIG_USBC_VCONN +#define CONFIG_USBC_VCONN_SWAP + +/* RTC */ +#define CONFIG_CMD_RTC +#define CONFIG_HOSTCMD_RTC + +/* Sensors */ +/* Enable sensor fifo, must also define the _SIZE and _THRES */ +#define CONFIG_ACCEL_FIFO +/* FIFO size is a power of 2. */ +#define CONFIG_ACCEL_FIFO_SIZE 256 +/* Depends on how fast the AP boots and typical ODRs. */ +#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) +#define CONFIG_CMD_ACCELS +#define CONFIG_CMD_ACCEL_INFO + +/* PD */ +#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ +#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ +#define PD_VCONN_SWAP_DELAY 5000 /* us */ + +#define PD_OPERATING_POWER_MW 15000 +#define PD_MAX_POWER_MW ((PD_MAX_VOLTAGE_MV * PD_MAX_CURRENT_MA) / 1000) +#define PD_MAX_CURRENT_MA 3000 +#define PD_MAX_VOLTAGE_MV 20000 + +/* Chipset */ +#define CONFIG_CHIPSET_SC7180 +#define CONFIG_CHIPSET_RESET_HOOK +#define CONFIG_POWER_COMMON +#define CONFIG_POWER_PP5000_CONTROL + +/* NPCX Features */ +#define CONFIG_HIBERNATE_PSL + +/* + * Macros for GPIO signals used in common code that don't match the + * schematic names. Signal names in gpio.inc match the schematic and are + * then redefined here to so it's more clear which signal is being used for + * which purpose. + */ +#define GPIO_AC_PRESENT GPIO_ACOK_OD +#define GPIO_POWER_BUTTON_L GPIO_EC_PWR_BTN_ODL +#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL +#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL +#define GPIO_WP_L GPIO_EC_WP_ODL +#define GPIO_LID_OPEN GPIO_LID_OPEN_EC +#define GPIO_SHI_CS_L GPIO_AP_EC_SPI_CS_L +#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW +#define GPIO_BATT_PRES_ODL GPIO_EC_BATT_PRES_ODL +#define GPIO_EN_PP5000 GPIO_EN_PP5000_A +#define GPIO_ENABLE_BACKLIGHT GPIO_EC_BL_DISABLE_L +#define GPIO_BOARD_VERSION1 GPIO_BRD_ID0 +#define GPIO_BOARD_VERSION2 GPIO_BRD_ID1 +#define GPIO_BOARD_VERSION3 GPIO_BRD_ID2 +#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV + +/* I2C Ports */ +#define I2C_PORT_BATTERY I2C_PORT_POWER +#define I2C_PORT_CHARGER I2C_PORT_POWER +#define I2C_PORT_ACCEL I2C_PORT_SENSOR +#define I2C_PORT_POWER NPCX_I2C_PORT0_0 +#define I2C_PORT_TCPC0 NPCX_I2C_PORT1_0 +#define I2C_PORT_TCPC1 NPCX_I2C_PORT2_0 +#define I2C_PORT_EEPROM NPCX_I2C_PORT5_0 +#define I2C_PORT_SENSOR NPCX_I2C_PORT7_0 + +#ifndef __ASSEMBLER__ + +enum power_signal { + SC7180_AP_RST_ASSERTED = 0, + SC7180_PS_HOLD, + SC7180_PMIC_FAULT_L, + SC7180_POWER_GOOD, + SC7180_WARM_RESET, + SC7180_AP_SUSPEND, + SC7180_DEPRECATED_AP_RST_REQ, + /* Number of power signals */ + POWER_SIGNAL_COUNT +}; + +#endif /* !defined(__ASSEMBLER__) */ + +#endif /* __CROS_EC_BASEBOARD_H */ |