diff options
Diffstat (limited to 'board/agah/board.h')
| -rw-r--r-- | board/agah/board.h | 204 |
1 files changed, 204 insertions, 0 deletions
diff --git a/board/agah/board.h b/board/agah/board.h new file mode 100644 index 0000000000..1dd4a23b9f --- /dev/null +++ b/board/agah/board.h @@ -0,0 +1,204 @@ +/* Copyright 2021 The Chromium OS Authors. All rights reserved. + * Use of this source code is governed by a BSD-style license that can be + * found in the LICENSE file. + */ + +/* Agah board configuration */ + +#ifndef __CROS_EC_BOARD_H +#define __CROS_EC_BOARD_H + +#include "compile_time_macros.h" + +/* + * Early agah boards are not set up for vivaldi + */ +#undef CONFIG_KEYBOARD_VIVALDI + +/* Baseboard features */ +#include "baseboard.h" + +/* + * This will happen automatically on NPCX9 ES2 and later. Do not remove + * until we can confirm all earlier chips are out of service. + */ +#define CONFIG_HIBERNATE_PSL_VCC1_RST_WAKEUP + +/* LED */ +#define CONFIG_LED_PWM +#define CONFIG_LED_PWM_COUNT 2 +#undef CONFIG_LED_PWM_NEAR_FULL_COLOR +#undef CONFIG_LED_PWM_SOC_ON_COLOR +#undef CONFIG_LED_PWM_SOC_SUSPEND_COLOR +#undef CONFIG_LED_PWM_LOW_BATT_COLOR +#define CONFIG_LED_PWM_NEAR_FULL_COLOR EC_LED_COLOR_WHITE +#define CONFIG_LED_PWM_SOC_ON_COLOR EC_LED_COLOR_WHITE +#define CONFIG_LED_PWM_SOC_SUSPEND_COLOR EC_LED_COLOR_WHITE +#define CONFIG_LED_PWM_LOW_BATT_COLOR EC_LED_COLOR_AMBER + +/* Sensors */ +#undef CONFIG_TABLET_MODE +#undef CONFIG_TABLET_MODE_SWITCH +#undef CONFIG_GMR_TABLET_MODE + +/* Buttons */ +#undef CONFIG_VOLUME_BUTTONS + +/* USB Type A Features */ +#define USB_PORT_COUNT 1 +#define CONFIG_USB_PORT_POWER_DUMB + +/* USB Type C and USB PD defines */ +#define CONFIG_USB_PD_REQUIRE_AP_MODE_ENTRY + +#define CONFIG_USB_PD_TCPM_PS8815 +#define CONFIG_USB_PD_TCPM_PS8815_FORCE_DID + +/* I2C speed console command */ +#define CONFIG_CMD_I2C_SPEED + +/* I2C control host command */ +#define CONFIG_HOSTCMD_I2C_CONTROL + +#define CONFIG_USBC_PPC_SYV682X +#define CONFIG_USBC_PPC_NX20P3483 + +#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ +#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ +#define PD_VCONN_SWAP_DELAY 5000 /* us */ + +/* + * Passive USB-C cables only support up to 60W. + */ +#define PD_OPERATING_POWER_MW 15000 +#define PD_MAX_POWER_MW 60000 +#define PD_MAX_CURRENT_MA 3000 +#define PD_MAX_VOLTAGE_MV 20000 + +/* + * Macros for GPIO signals used in common code that don't match the + * schematic names. Signal names in gpio.inc match the schematic and are + * then redefined here to so it's more clear which signal is being used for + * which purpose. + */ +#define GPIO_AC_PRESENT GPIO_ACOK_OD +#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL +#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL +#define GPIO_ENABLE_BACKLIGHT GPIO_EC_EN_EDP_BL +#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW +#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV +#define GPIO_PACKET_MODE_EN GPIO_EC_GSC_PACKET_MODE +#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL +#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L +#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST +#define GPIO_PCH_SLP_S0_L GPIO_SYS_SLP_S0IX_L +#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L + +/* + * GPIO_EC_PCH_INT_ODL is used for MKBP events as well as a PCH wakeup + * signal. + */ +#define GPIO_PCH_WAKE_L GPIO_EC_PCH_INT_ODL +#define GPIO_PG_EC_ALL_SYS_PWRGD GPIO_SEQ_EC_ALL_SYS_PG +#define GPIO_PG_EC_DSW_PWROK GPIO_SEQ_EC_DSW_PWROK +#define GPIO_PG_EC_RSMRST_ODL GPIO_SEQ_EC_RSMRST_ODL +#define GPIO_POWER_BUTTON_L GPIO_GSC_EC_PWR_BTN_ODL +#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL +#define GPIO_WP_L GPIO_EC_WP_ODL + +/* System has back-lit keyboard */ +#define CONFIG_PWM_KBLIGHT + +/* I2C Bus Configuration */ + +#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 + +#define I2C_PORT_USB_C0_C2_TCPC NPCX_I2C_PORT1_0 +#define I2C_PORT_USB_C1_TCPC NPCX_I2C_PORT4_1 + +#define I2C_PORT_USB_C0_C2_PPC NPCX_I2C_PORT2_0 +#define I2C_PORT_USB_C1_PPC NPCX_I2C_PORT6_1 + +#define I2C_PORT_USB_C0_C2_BC12 NPCX_I2C_PORT2_0 +#define I2C_PORT_USB_C1_BC12 NPCX_I2C_PORT6_1 + +#define I2C_PORT_USB_C0_C2_MUX NPCX_I2C_PORT3_0 +#define I2C_PORT_USB_C1_MUX NPCX_I2C_PORT6_1 + +#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0 +#define I2C_PORT_CHARGER NPCX_I2C_PORT7_0 +#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 + +#define I2C_ADDR_EEPROM_FLAGS 0x50 + +/* Thermal features */ +#define CONFIG_THERMISTOR +#define CONFIG_TEMP_SENSOR +#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_SEQ_EC_DSW_PWROK +#define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B + +#define CONFIG_FANS FAN_CH_COUNT + +/* Charger defines */ +#define CONFIG_CHARGER_ISL9241 +#define CONFIG_CHARGE_RAMP_SW +#define CONFIG_CHARGER_SENSE_RESISTOR 10 +#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 + +/* + * Older boards have a different ADC assignment. + */ + +#define CONFIG_ADC_CHANNELS_RUNTIME_CONFIG + +#ifndef __ASSEMBLER__ + +#include "gpio_signal.h" /* needed by registers.h */ +#include "registers.h" +#include "usbc_config.h" + +enum adc_channel { + ADC_TEMP_SENSOR_1_DDR_SOC, + ADC_TEMP_SENSOR_2_AMBIENT, + ADC_TEMP_SENSOR_3_CHARGER, + ADC_TEMP_SENSOR_4_WWAN, + ADC_CH_COUNT +}; + +enum temp_sensor_id { + TEMP_SENSOR_1_DDR_SOC, + TEMP_SENSOR_2_AMBIENT, + TEMP_SENSOR_3_CHARGER, + TEMP_SENSOR_4_WWAN, + TEMP_SENSOR_COUNT +}; + +enum battery_type { + BATTERY_DYNAPACK_COSMX, + BATTERY_DYNAPACK_HIGHPOWER, + BATTERY_TYPE_COUNT +}; + +enum pwm_channel { + PWM_CH_LED2 = 0, /* PWM0 (white charger) */ + PWM_CH_LED3, /* PWM1 (orange on DB) */ + PWM_CH_LED1, /* PWM2 (orange charger) */ + PWM_CH_KBLIGHT, /* PWM3 */ + PWM_CH_FAN, /* PWM5 */ + PWM_CH_LED4, /* PWM7 (white on DB) */ + PWM_CH_COUNT +}; + +enum fan_channel { + FAN_CH_0 = 0, + FAN_CH_COUNT +}; + +enum mft_channel { + MFT_CH_0 = 0, + MFT_CH_COUNT +}; + +#endif /* !__ASSEMBLER__ */ + +#endif /* __CROS_EC_BOARD_H */ |