diff options
Diffstat (limited to 'board/arcada_ish/board.h')
| -rw-r--r-- | board/arcada_ish/board.h | 127 |
1 files changed, 0 insertions, 127 deletions
diff --git a/board/arcada_ish/board.h b/board/arcada_ish/board.h deleted file mode 100644 index ca69c1ba15..0000000000 --- a/board/arcada_ish/board.h +++ /dev/null @@ -1,127 +0,0 @@ -/* Copyright 2018 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Arcada ISH board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* - * By default, enable all console messages except HC, ACPI and event - * The sensor stack is generating a lot of activity. - */ -#undef CONFIG_HOSTCMD_DEBUG_MODE -#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF - -/* ISH specific*/ -#undef CONFIG_DEBUG_ASSERT -#define CONFIG_CLOCK_CRYSTAL -/* EC */ -#define CONFIG_FLASH_SIZE 0x80000 -#define CONFIG_FPU -#define CONFIG_I2C -#define CONFIG_I2C_MASTER - -#define CONFIG_ACCEL_LNG2DM /* Base sensor: LNG2DM - * (uses LIS2DH driver) - */ -#define CONFIG_ACCELGYRO_LSM6DSM /* Lid sensor: LSM6DS3 - * (uses LSM6DSM driver) - */ -#define CONFIG_MAG_LIS2MDL /* Lid sensor: LIS2DML */ -#define CONFIG_MAG_CALIBRATE - -#define CONFIG_ACCEL_INTERRUPTS -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* FIFO size is a power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -/* Depends on how fast the AP boots and typical ODRs. */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK (BIT(BASE_ACCEL) | BIT(LID_MAG)) - -#define CONFIG_ACCEL_LSM6DSM_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL) - -#define CONFIG_MKBP_EVENT -#define CONFIG_MKBP_USE_HECI - -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL - -#define CONFIG_TABLET_MODE -#define CONFIG_GMR_TABLET_MODE -#define CONFIG_GMR_TABLET_MODE_CUSTOM -#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L - -/* DMA paging between SRAM and DRAM */ -#define CONFIG_DMA_PAGING - -/* Host command over HECI */ -#define CONFIG_HOSTCMD_HECI - -/* I2C ports */ -#define I2C_PORT_SENSOR ISH_I2C0 -#define CONFIG_CMD_I2C_XFER - -/* EC Console Commands */ -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO -#define CONFIG_CMD_TIMERINFO - -/* Undefined features */ -#undef CONFIG_CMD_HASH -#undef CONFIG_CMD_I2C_SCAN -#undef CONFIG_CMD_KEYBOARD -#undef CONFIG_CMD_POWER_AP -#undef CONFIG_CMD_POWERINDEBUG -#undef CONFIG_CMD_SHMEM -#undef CONFIG_EXTPOWER -#undef CONFIG_KEYBOARD_KSO_BASE -#undef CONFIG_FLASH -#undef CONFIG_FMAP -#undef CONFIG_SWITCH - -/* Modules we want to exclude */ -#undef CONFIG_CMD_HASH -#undef CONFIG_CMD_TEMP_SENSOR -#undef CONFIG_ADC -#undef CONFIG_SHA256 - -/* power management definitions */ -#define CONFIG_LOW_POWER_IDLE - -#define CONFIG_ISH_PM_D0I1 -#define CONFIG_ISH_PM_D0I2 -#define CONFIG_ISH_PM_D0I3 -#define CONFIG_ISH_PM_D3 -#define CONFIG_ISH_PM_RESET_PREP - -#define CONFIG_ISH_D0I2_MIN_USEC (15*MSEC) /* need final tune */ -#define CONFIG_ISH_D0I3_MIN_USEC (100*MSEC) /* need final tune */ - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -/* Motion sensors - * - * Note: Since we aren't using LPC memory map to transmit sensor data, the - * order of this enum does not need to be accel, accel, gyro - */ -enum sensor_id { - LID_ACCEL, - LID_GYRO, - BASE_ACCEL, - LID_MAG, - SENSOR_COUNT -}; - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ |