diff options
Diffstat (limited to 'board/asurada/board.h')
| -rw-r--r-- | board/asurada/board.h | 193 |
1 files changed, 3 insertions, 190 deletions
diff --git a/board/asurada/board.h b/board/asurada/board.h index b0af44d571..b7ad4341fb 100644 --- a/board/asurada/board.h +++ b/board/asurada/board.h @@ -7,96 +7,26 @@ #ifndef __CROS_EC_BOARD_H #define __CROS_EC_BOARD_H +#include "baseboard.h" + /* Chipset config */ -#define CONFIG_BOARD_RESET_AFTER_POWER_ON #define CONFIG_BRINGUP -#define CONFIG_CHIPSET_MT8192 -#define CONFIG_CMD_AP_RESET_LOG -#define CONFIG_CMD_POWERINDEBUG -#define CONFIG_HIBERNATE_WAKE_PINS_DYNAMIC -#define CONFIG_POWER_COMMON /* Optional features */ #define CONFIG_SYSTEM_UNLOCKED #define CONFIG_LTO -#define CONFIG_BOARD_VERSION_CUSTOM -#define CONFIG_EXTPOWER_GPIO -/* - * NOTE: we need to make correct VCC voltage selection here if EC's VCC isn't - * connect to 1.8v on other versions. - */ -#define CONFIG_IT83XX_VCC_1P8V /* * TODO: Remove this option once the VBAT no longer keeps high when * system's power isn't presented. */ #define CONFIG_IT83XX_RESET_PD_CONTRACT_IN_BRAM -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_LOW_POWER_S0 -#define CONFIG_POWER_BUTTON -#define CONFIG_PWM -#define CONFIG_VBOOT_HASH -#define CONFIG_VOLUME_BUTTONS -#define CONFIG_WP_ACTIVE_HIGH - -/* Battery */ -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_FUEL_GAUGE -#define CONFIG_BATTERY_PRESENT_GPIO GPIO_EC_BATT_PRES_ODL -#define CONFIG_BATTERY_SMART /* BC12 */ -#define CONFIG_BC12_DETECT_MT6360 -#define CONFIG_BC12_DETECT_PI3USB9201 -#undef CONFIG_BC12_SINGLE_DRIVER /* TODO(b/159583342): remove after rev0 deprecated */ #define CONFIG_MT6360_BC12_GPIO -#define CONFIG_USB_CHARGER - -/* Charger */ -#define ADC_AMON_BMON ADC_CHARGER_AMON_R /* ADC name remap */ -#define ADC_PSYS ADC_CHARGER_PMON /* ADC name remap */ -#define CONFIG_CHARGER -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_INPUT_CURRENT 512 -#define CONFIG_CHARGER_ISL9238C -#define CONFIG_CHARGER_MAINTAIN_VBAT -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 /* BOARD_RS1 */ -#define CONFIG_CHARGER_SENSE_RESISTOR 10 /* BOARD_RS2 */ -#define CONFIG_CHARGER_OTG -#define CONFIG_CHARGER_PSYS -#define CONFIG_CHARGER_PSYS_READ -#define CONFIG_CHARGE_RAMP_HW -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CMD_CHARGER_ADC_AMON_BMON - -/* Chipset */ -#define CONFIG_HOST_COMMAND_STATUS - -/* Keyboard */ -#define CONFIG_CMD_KEYBOARD -#define CONFIG_KEYBOARD_COL2_INVERTED -#define CONFIG_KEYBOARD_PROTOCOL_MKBP -#define CONFIG_MKBP_USE_GPIO - -/* I2C */ -#define CONFIG_I2C -#define CONFIG_I2C_CONTROLLER -#define CONFIG_I2C_PASSTHRU_RESTRICTED -#define CONFIG_I2C_VIRTUAL_BATTERY -#define I2C_PORT_CHARGER IT83XX_I2C_CH_A -#define I2C_PORT_BATTERY IT83XX_I2C_CH_A -#define I2C_PORT_ACCEL IT83XX_I2C_CH_B -#define I2C_PORT_PPC0 IT83XX_I2C_CH_C -#define I2C_PORT_PPC1 IT83XX_I2C_CH_E -#define I2C_PORT_USB_MUX0 IT83XX_I2C_CH_C -#define I2C_PORT_USB_MUX1 IT83XX_I2C_CH_E -#define I2C_PORT_VIRTUAL_BATTERY I2C_PORT_BATTERY -#define CONFIG_SMBUS_PEC /* LED */ -#define CONFIG_LED_COMMON #ifdef BOARD_HAYATO #define CONFIG_LED_POWER_LED #define CONFIG_LED_ONOFF_STATES @@ -104,48 +34,7 @@ #endif /* PD / USB-C / PPC */ -#define CONFIG_CMD_PPC_DUMP -#define CONFIG_HOSTCMD_PD_CONTROL -#define CONFIG_USBC_PPC -#define CONFIG_USBC_PPC_DEDICATED_INT -#define CONFIG_USBC_PPC_POLARITY -#define CONFIG_USBC_PPC_SYV682X -#define CONFIG_USBC_PPC_VCONN -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP -#define CONFIG_USB_DRP_ACC_TRYSRC -#define CONFIG_USB_MUX_IT5205 /* C0 */ -#define CONFIG_USB_MUX_PS8743 /* C1 */ -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP #define CONFIG_USB_PD_DEBUG_LEVEL 3 -#define CONFIG_USB_PD_DECODE_SOP -#define CONFIG_USB_PD_DISCHARGE -#define CONFIG_USB_PD_DISCHARGE_PPC -#define CONFIG_USB_PD_DP_HPD_GPIO -#define CONFIG_USB_PD_DP_HPD_GPIO_CUSTOM -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_REV30 -#define CONFIG_USB_PD_ITE_ACTIVE_PORT_COUNT 2 -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_TCPMV2 -#define CONFIG_USB_PD_TCPM_ITE_ON_CHIP -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_TRY_SRC -#define CONFIG_USB_PD_VBUS_DETECT_PPC -#define CONFIG_USB_PID 0x5566 /* TODO: update PID */ -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_IT83XX_TUNE_CC_PHY - -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 60000 -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ /* Optional console commands */ #define CONFIG_CMD_FLASH @@ -158,10 +47,6 @@ #define CONFIG_TABLET_MODE_SWITCH #define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L -#define CONFIG_ACCEL_FIFO -#define CONFIG_ACCEL_FIFO_SIZE 256 -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) -#define CONFIG_ACCEL_INTERRUPTS #define CONFIG_ACCELGYRO_BMI160 /* Base accel */ #define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) @@ -176,9 +61,6 @@ #define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL #define CONFIG_LID_ANGLE_UPDATE -#define CONFIG_CMD_ACCEL_INFO -#define CONFIG_CMD_ACCELS - #ifdef BOARD_ASURADA_REV0 #define CONFIG_ALS #define ALS_COUNT 1 @@ -196,43 +78,9 @@ /* SPI / Host Command */ #undef CONFIG_HOSTCMD_DEBUG_MODE #define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF -#define CONFIG_SPI -#define CONFIG_SUPPRESSED_HOST_COMMANDS \ - EC_CMD_CONSOLE_SNAPSHOT, EC_CMD_CONSOLE_READ, EC_CMD_MOTION_SENSE_CMD, \ - EC_CMD_PD_GET_LOG_ENTRY - -/* MKBP */ -#define CONFIG_MKBP_EVENT - -#define CONFIG_KEYBOARD_PROTOCOL_MKBP -#define CONFIG_MKBP_USE_GPIO - -/* Define the host events which are allowed to wakeup AP in S3. */ -#define CONFIG_MKBP_HOST_EVENT_WAKEUP_MASK \ - (EC_HOST_EVENT_MASK(EC_HOST_EVENT_AC_CONNECTED) | \ - EC_HOST_EVENT_MASK(EC_HOST_EVENT_AC_DISCONNECTED) | \ - EC_HOST_EVENT_MASK(EC_HOST_EVENT_LID_OPEN) | \ - EC_HOST_EVENT_MASK(EC_HOST_EVENT_MODE_CHANGE) | /* for DP */ \ - EC_HOST_EVENT_MASK(EC_HOST_EVENT_POWER_BUTTON)) - -/* UART */ -#undef CONFIG_UART_TX_BUF_SIZE -#define CONFIG_UART_TX_BUF_SIZE 4096 /* USB-A */ -#define CONFIG_USB_PORT_POWER_DUMB -#define USB_PORT_COUNT 1 - -/* GPIO name remapping */ -#define GPIO_EN_HDMI_PWR GPIO_EC_X_GPIO1 -#define GPIO_USB_C1_FRS_EN GPIO_EC_X_GPIO1 -#define GPIO_USB_C1_PPC_INT_ODL GPIO_X_EC_GPIO2 -#define GPIO_PS185_EC_DP_HPD GPIO_X_EC_GPIO2 -#define GPIO_USB_C1_DP_IN_HPD GPIO_EC_X_GPIO3 -#define GPIO_PS185_PWRDN_ODL GPIO_EC_X_GPIO3 - -/* Voltage regulator control */ -#define CONFIG_HOSTCMD_REGULATOR +#define USBA_PORT_COUNT 1 #ifndef __ASSEMBLER__ @@ -244,39 +92,6 @@ enum battery_type { BATTERY_TYPE_COUNT, }; -enum pwm_channel { - PWM_CH_LED1, - PWM_CH_LED2, - PWM_CH_LED3, - PWM_CH_COUNT, -}; - -enum adc_channel { - ADC_VBUS, /* ADC 0 */ - ADC_BOARD_ID_0, /* ADC 1 */ - ADC_BOARD_ID_1, /* ADC 2 */ - ADC_CHARGER_AMON_R, /* ADC 3 */ - ADC_CHARGER_PMON, /* ADC 6 */ - - /* Number of ADC channels */ - ADC_CH_COUNT, -}; - -enum power_signal { - PMIC_PWR_GOOD, - AP_IN_S3_L, - AP_WDT_ASSERTED, - POWER_SIGNAL_COUNT, -}; - -enum board_sub_board { - SUB_BOARD_NONE = -1, - SUB_BOARD_TYPEC, - SUB_BOARD_HDMI, - - SUB_BOARD_COUNT, -}; - enum sensor_id { BASE_ACCEL = 0, BASE_GYRO, @@ -288,8 +103,6 @@ enum sensor_id { SENSOR_COUNT, }; -void board_reset_pd_mcu(void); -int board_get_version(void); int board_accel_force_mode_mask(void); #endif /* !__ASSEMBLER__ */ |