diff options
Diffstat (limited to 'board/bolt/board.h')
| -rw-r--r-- | board/bolt/board.h | 205 |
1 files changed, 0 insertions, 205 deletions
diff --git a/board/bolt/board.h b/board/bolt/board.h deleted file mode 100644 index 0ab6ea67a0..0000000000 --- a/board/bolt/board.h +++ /dev/null @@ -1,205 +0,0 @@ -/* Copyright (c) 2013 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Configuration for Bolt mainboard */ - -#ifndef __BOARD_H -#define __BOARD_H - -/* Debug features */ -#define CONFIG_CONSOLE_CMDHELP -#define CONFIG_TASK_PROFILING - -/* Optional features */ -#define CONFIG_CHIPSET_X86 -#define CONFIG_CHIPSET_CAN_THROTTLE -#define CONFIG_EXTPOWER_GPIO -#define CONFIG_KEYBOARD_BOARD_CONFIG -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#define CONFIG_LED_DRIVER_DS2413 -#define CONFIG_ONEWIRE -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 -#define CONFIG_WP_ACTIVE_HIGH - -#define CONFIG_BATTERY_CHECK_CONNECTED -#define CONFIG_BATTERY_LINK -#define CONFIG_BATTERY_SMART -#define CONFIG_BACKLIGHT_LID -#define CONFIG_BACKLIGHT_REQ_GPIO GPIO_PCH_BKLTEN -#define CONFIG_CHARGER -#define CONFIG_CHARGER_BQ24715 -/* 10mOhm sense resitors. */ -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 -/* External Charger maximum current. */ -#define CONFIG_CHARGER_INPUT_CURRENT 5000 -#define CONFIG_FANS 1 -#define CONFIG_PWM -#define CONFIG_PWM_KBLIGHT -#define CONFIG_SWITCH_DEDICATED_RECOVERY -#define CONFIG_TEMP_SENSOR -#define CONFIG_UART_HOST 2 -#define CONFIG_WIRELESS -#if 0 -#define CONFIG_USB_PORT_POWER_DUMB -#endif - - -#ifndef __ASSEMBLER__ - -/* I2C ports */ -#define I2C_PORT_BATTERY 0 -#define I2C_PORT_CHARGER 0 -#define I2C_PORT_LIGHTBAR 1 -#define I2C_PORT_THERMAL 5 - -/* 13x8 keyboard scanner uses an entire GPIO bank for row inputs */ -#define KB_SCAN_ROW_IRQ LM4_IRQ_GPIOK -#define KB_SCAN_ROW_GPIO LM4_GPIO_K - -/* Host connects to keyboard controller module via LPC */ -#define HOST_KB_BUS_LPC - -/* USB ports */ -#define USB_PORT_COUNT 2 - -/* GPIO signal definitions. */ -enum gpio_signal { - /* Inputs with interrupt handlers are first for efficiency */ - GPIO_POWER_BUTTON_L = 0, /* Power button */ - GPIO_LID_OPEN, /* Lid switch */ - GPIO_AC_PRESENT, /* AC power present */ - GPIO_PCH_BKLTEN, /* Backlight enable signal from PCH */ - GPIO_PCH_SLP_S0_L, /* SLP_S0# signal from PCH */ - GPIO_PCH_SLP_S3_L, /* SLP_S3# signal from PCH */ - GPIO_PCH_SLP_S5_L, /* SLP_S5# signal from PCH */ - GPIO_PCH_SLP_SUS_L, /* SLP_SUS# signal from PCH */ - GPIO_PCH_SUSWARN_L, /* SUSWARN# signal from PCH */ - GPIO_PP1050_PGOOD, /* Power good on 1.05V */ - GPIO_PP1350_PGOOD, /* Power good on 1.35V (DRAM) */ - GPIO_PP5000_PGOOD, /* Power good on 5V */ - GPIO_VCORE_PGOOD, /* Power good on core VR */ - GPIO_PCH_EDP_VDD_EN, /* PCH wants EDP enabled */ - GPIO_RECOVERY_L, /* Recovery signal from servo */ - GPIO_WP, /* Write protect input */ - - /* Other inputs */ - GPIO_BOARD_VERSION1, /* Board version stuffing resistor 1 */ - GPIO_BOARD_VERSION2, /* Board version stuffing resistor 2 */ - GPIO_BOARD_VERSION3, /* Board version stuffing resistor 3 */ - GPIO_CPU_PGOOD, /* Power good to the CPU */ - GPIO_ONEWIRE, /* One-wire bus to adapter LED */ - GPIO_PCH_CATERR_L, /* Catastrophic error signal from PCH */ - GPIO_THERMAL_DATA_READY_L, /* From thermal sensor */ - GPIO_USB1_OC_L, /* USB port overcurrent warning */ - GPIO_USB1_STATUS_L, /* USB charger port 1 status output */ - GPIO_USB2_OC_L, /* USB port overcurrent warning */ - GPIO_USB2_STATUS_L, /* USB charger port 2 status output */ - GPIO_BAT_DETECT_L, /* Battery detect from BAT_TEMP */ - - /* Outputs */ - GPIO_CPU_PROCHOT, /* Force CPU to think it's overheated */ - GPIO_PP1350_EN, /* Enable 1.35V supply */ - GPIO_PP3300_DSW_GATED_EN, /* Enable DSW rails */ - GPIO_PP3300_DX_EN, /* Enable power to lots of peripherals */ - GPIO_PP3300_LTE_EN, /* Enable LTE radio */ - GPIO_PP3300_WLAN_EN, /* Enable WiFi power */ - GPIO_PP1050_EN, /* Enable 1.05V regulator */ - GPIO_VCORE_EN, /* Stuffing option - not connected */ - GPIO_PP5000_EN, /* Enable 5V supply */ - GPIO_SYS_PWROK, /* EC thinks everything is up and ready */ - GPIO_WLAN_OFF_L, /* Disable WiFi radio */ - - GPIO_ENABLE_BACKLIGHT, /* Enable backlight power */ - GPIO_ENABLE_TOUCHPAD, /* Enable touchpad power */ - GPIO_ENTERING_RW, /* Indicate when EC is entering RW code */ - GPIO_LIGHTBAR_RESET_L, /* Reset lightbar controllers */ - GPIO_PCH_DPWROK, /* Indicate when VccDSW is good */ - - GPIO_PCH_HDA_SDO, /* HDA_SDO signal to PCH; when high, ME - * ignores security descriptor */ - GPIO_PCH_WAKE_L, /* Wake signal from EC to PCH */ - GPIO_PCH_NMI_L, /* Non-maskable interrupt pin to PCH */ - GPIO_PCH_PWRBTN_L, /* Power button output to PCH */ - GPIO_PCH_PWROK, /* PWROK / APWROK signals to PCH */ - GPIO_PCH_RCIN_L, /* RCIN# line to PCH (for 8042 emulation) */ - GPIO_PCH_SYS_RST_L, /* Reset PCH resume power plane logic */ - GPIO_PCH_SMI_L, /* System management interrupt to PCH */ - GPIO_TOUCHSCREEN_RESET_L, /* Reset touch screen */ - GPIO_EC_EDP_VDD_EN, /* Enable EDP (passthru from PCH) */ - GPIO_LPC_CLKRUN_L, /* Dunno. Probably important, though. */ - - GPIO_USB1_CTL1, /* USB charger port 1 CTL1 output */ - GPIO_USB1_CTL2, /* USB charger port 1 CTL2 output */ - GPIO_USB1_CTL3, /* USB charger port 1 CTL3 output */ - GPIO_USB1_ENABLE, /* USB charger port 1 enable */ - GPIO_USB1_ILIM_SEL, /* USB charger port 1 ILIM_SEL output */ - GPIO_USB2_CTL1, /* USB charger port 2 CTL1 output */ - GPIO_USB2_CTL2, /* USB charger port 2 CTL2 output */ - GPIO_USB2_CTL3, /* USB charger port 2 CTL3 output */ - GPIO_USB2_ENABLE, /* USB charger port 2 enable */ - GPIO_USB2_ILIM_SEL, /* USB charger port 2 ILIM_SEL output */ - - /* Number of GPIOs; not an actual GPIO */ - GPIO_COUNT -}; - -/* x86 signal definitions */ -enum x86_signal { - X86_PGOOD_PP5000 = 0, - X86_PGOOD_PP1350, - X86_PGOOD_VCORE, - X86_PCH_SLP_S0n_DEASSERTED, - X86_PCH_SLP_S3n_DEASSERTED, - X86_PCH_SLP_S5n_DEASSERTED, - X86_PCH_SLP_SUSn_DEASSERTED, - - /* Number of X86 signals */ - X86_SIGNAL_COUNT -}; - -enum adc_channel { - /* EC internal die temperature in degrees K. */ - ADC_CH_EC_TEMP = 0, - - /* Charger current in mA. */ - ADC_CH_CHARGER_CURRENT, - - ADC_CH_COUNT -}; - -enum pwm_channel { - PWM_CH_KBLIGHT, - - /* Number of PWM channels */ - PWM_CH_COUNT -}; - -enum temp_sensor_id { - /* HEY - need two I2C sensor values, and put PECI first */ - - /* EC internal temperature sensor */ - TEMP_SENSOR_EC_INTERNAL, - /* CPU die temperature via PECI */ - TEMP_SENSOR_CPU_PECI, - - TEMP_SENSOR_COUNT -}; - -/* Known board versions for system_get_board_version(). */ -enum board_version { - BOARD_VERSION_PROTO1 = 0, - BOARD_VERSION_EVT = 1, -}; - -/* Wireless signals */ -#define WIRELESS_GPIO_WLAN GPIO_WLAN_OFF_L -#define WIRELESS_GPIO_WWAN GPIO_PP3300_LTE_EN -#define WIRELESS_GPIO_WLAN_POWER GPIO_PP3300_WLAN_EN - -#endif /* !__ASSEMBLER__ */ - -#endif /* __BOARD_H */ |