diff options
Diffstat (limited to 'board/chell/board.c')
-rw-r--r-- | board/chell/board.c | 25 |
1 files changed, 13 insertions, 12 deletions
diff --git a/board/chell/board.c b/board/chell/board.c index 6311dc6c9c..7ecad3f1c1 100644 --- a/board/chell/board.c +++ b/board/chell/board.c @@ -42,7 +42,7 @@ #define CPRINTS(format, args...) cprints(CC_USBCHARGE, format, ## args) #define CPRINTF(format, args...) cprintf(CC_USBCHARGE, format, ## args) -#define I2C_ADDR_BD99992 0x60 +#define I2C_ADDR_BD99992__7bf 0x30 /* Exchange status with PD MCU. */ static void pd_mcu_interrupt(enum gpio_signal signal) @@ -111,7 +111,7 @@ const struct tcpc_config_t tcpc_config[CONFIG_USB_PD_PORT_COUNT] = { .bus_type = EC_BUS_TYPE_I2C, .i2c_info = { .port = I2C_PORT_TCPC, - .addr = CONFIG_TCPC_I2C_BASE_ADDR, + .addr__7bf = CONFIG_TCPC_I2C_BASE_ADDR__7BF, }, .drv = &tcpci_tcpm_drv, }, @@ -119,7 +119,7 @@ const struct tcpc_config_t tcpc_config[CONFIG_USB_PD_PORT_COUNT] = { .bus_type = EC_BUS_TYPE_I2C, .i2c_info = { .port = I2C_PORT_TCPC, - .addr = CONFIG_TCPC_I2C_BASE_ADDR + 2, + .addr__7bf = CONFIG_TCPC_I2C_BASE_ADDR__7BF + 1, }, .drv = &tcpci_tcpm_drv, @@ -183,12 +183,12 @@ static int ps874x_tune_mux(int port) struct usb_mux usb_muxes[CONFIG_USB_PD_PORT_COUNT] = { { - .port_addr = 0x34, + .port_addr = 0x1A, .driver = &ps874x_usb_mux_driver, .board_init = &ps874x_tune_mux, }, { - .port_addr = 0x20, + .port_addr = 0x10, .driver = &ps874x_usb_mux_driver, .board_init = &ps874x_tune_mux, } @@ -230,7 +230,7 @@ BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT); static void board_pmic_init(void) { /* DISCHGCNT3 - enable 100 ohm discharge on V1.00A */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992, 0x3e, 0x04); + i2c_write8__7bf(I2C_PORT_PMIC, I2C_ADDR_BD99992__7bf, 0x3e, 0x04); /* * No need to re-init below settings since they are present on all MP @@ -240,23 +240,23 @@ static void board_pmic_init(void) return; /* Set CSDECAYEN / VCCIO decays to 0V at assertion of SLP_S0# */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992, 0x30, 0x4a); + i2c_write8__7bf(I2C_PORT_PMIC, I2C_ADDR_BD99992__7bf, 0x30, 0x4a); /* * Set V100ACNT / V1.00A Control Register: * Nominal output = 1.0V. */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992, 0x37, 0x1a); + i2c_write8__7bf(I2C_PORT_PMIC, I2C_ADDR_BD99992__7bf, 0x37, 0x1a); /* * Set V085ACNT / V0.85A Control Register: * Lower power mode = 0.7V. * Nominal output = 1.0V. */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992, 0x38, 0x7a); + i2c_write8__7bf(I2C_PORT_PMIC, I2C_ADDR_BD99992__7bf, 0x38, 0x7a); /* VRMODECTRL - enable low-power mode for VCCIO and V0.85A */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992, 0x3b, 0x18); + i2c_write8__7bf(I2C_PORT_PMIC, I2C_ADDR_BD99992__7bf, 0x3b, 0x18); } DECLARE_HOOK(HOOK_INIT, board_pmic_init, HOOK_PRIO_DEFAULT); @@ -394,7 +394,7 @@ void board_hibernate(void) uart_flush_output(); /* Trigger PMIC shutdown. */ - if (i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992, 0x49, 0x01)) { + if (i2c_write8__7bf(I2C_PORT_PMIC, I2C_ADDR_BD99992__7bf, 0x49, 0x01)) { /* * If we can't tell the PMIC to shutdown, instead reset * and don't start the AP. Hopefully we'll be able to @@ -466,7 +466,8 @@ void chipset_set_pmic_slp_sus_l(int level) if (!level) msleep(25); - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992, 0x43, val); + i2c_write8__7bf(I2C_PORT_PMIC, I2C_ADDR_BD99992__7bf, + 0x43, val); previous_level = level; } } |