diff options
Diffstat (limited to 'board/cheza/board.h')
| -rw-r--r-- | board/cheza/board.h | 225 |
1 files changed, 0 insertions, 225 deletions
diff --git a/board/cheza/board.h b/board/cheza/board.h deleted file mode 100644 index 76e64277b5..0000000000 --- a/board/cheza/board.h +++ /dev/null @@ -1,225 +0,0 @@ -/* Copyright 2018 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Cheza board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* TODO(waihong): Remove the following bringup features */ -#define CONFIG_BRINGUP -#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands. */ -#define CONFIG_USB_PD_DEBUG_LEVEL 3 -#define CONFIG_CMD_AP_RESET_LOG -#define CONFIG_HOSTCMD_AP_RESET - -/* - * By default, enable all console messages excepted event and HC: - * The sensor stack is generating a lot of activity. - * They can be enabled through the console command 'chan'. - */ -#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_HOSTCMD))) - -/* NPCX7 config */ -#define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */ -#define NPCX_TACH_SEL2 0 /* No tach. */ -#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */ - -/* Internal SPI flash on NPCX7 */ -#define CONFIG_FLASH_SIZE (1024 * 1024) /* 1MB internal spi flash */ -#define CONFIG_SPI_FLASH_REGS -#define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */ -#define CONFIG_HOSTCMD_FLASH_SPI_INFO - -/* EC Modules */ -#define CONFIG_I2C -#define CONFIG_I2C_MASTER -#define CONFIG_LED_COMMON -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_ADC -#define CONFIG_BACKLIGHT_LID -#define CONFIG_FPU -#define CONFIG_PWM -#define CONFIG_PWM_DISPLIGHT - -#define CONFIG_VBOOT_HASH - -#define CONFIG_DETACHABLE_BASE - -#undef CONFIG_PECI - -#define CONFIG_HOSTCMD_SPS -#define CONFIG_HOST_COMMAND_STATUS -#define CONFIG_HOSTCMD_SECTION_SORTED /* Host commands are sorted. */ -#define CONFIG_MKBP_EVENT -#define CONFIG_KEYBOARD_PROTOCOL_MKBP -#define CONFIG_MKBP_USE_GPIO - -#define CONFIG_BOARD_VERSION_GPIO -#define CONFIG_POWER_BUTTON -#define CONFIG_VOLUME_BUTTONS -#define CONFIG_BUTTON_TRIGGERED_RECOVERY -#define CONFIG_EMULATED_SYSRQ -#define CONFIG_CMD_BUTTON -#define CONFIG_SWITCH -#define CONFIG_LID_SWITCH -#define CONFIG_EXTPOWER_GPIO - -#define CONFIG_TABLET_MODE -#define CONFIG_TABLET_MODE_SWITCH - -/* Battery */ -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_PRESENT_GPIO GPIO_BATT_PRES_ODL -#define CONFIG_BATTERY_SMART - -/* Charger */ -#define CONFIG_CHARGER -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGER_ISL9238 -#define CONFIG_CHARGE_RAMP_HW -#define CONFIG_USB_CHARGER -#define CONFIG_CMD_CHARGER_ADC_AMON_BMON -#define CONFIG_CHARGER_PSYS -#define CONFIG_CHARGER_PSYS_READ -#define CONFIG_CHARGER_DISCHARGE_ON_AC - -#define CONFIG_CHARGER_INPUT_CURRENT 512 -#define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 2 -#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON 7500 -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 - -/* BC 1.2 Charger */ -#define CONFIG_BC12_DETECT_PI3USB9281 -#define CONFIG_BC12_DETECT_PI3USB9281_CHIP_COUNT 2 - -/* USB */ -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_CMD_PD_CONTROL -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_DISCHARGE_PPC -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT TYPEC_RP_3A0 -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_TCPM_ANX3429 -#define CONFIG_USB_PD_TCPM_PS8751 -#define CONFIG_USB_PD_TCPM_MUX -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_TRY_SRC -#define CONFIG_USB_PD_VBUS_DETECT_CHARGER -#define CONFIG_USB_PD_5V_EN_CUSTOM -#define CONFIG_USB_MUX_VIRTUAL -#define CONFIG_USBC_PPC_SN5S330 -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP - -/* RTC */ -#define CONFIG_CMD_RTC -#define CONFIG_HOSTCMD_RTC - -/* Sensors */ -#define CONFIG_ACCELGYRO_BMI160 -#define CONFIG_ACCEL_INTERRUPTS -#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL) -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* FIFO size is a power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -/* Depends on how fast the AP boots and typical ODRs. */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO -#define CONFIG_ALS -#define CONFIG_ALS_OPT3001 -#define ALS_COUNT 1 -#define OPT3001_I2C_ADDR_FLAGS OPT3001_I2C_ADDR1_FLAGS - -/* PD */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ -#define PD_VCONN_SWAP_DELAY 5000 /* us */ - -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW ((PD_MAX_VOLTAGE_MV * PD_MAX_CURRENT_MA) / 1000) -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 - -/* Chipset */ -#define CONFIG_CHIPSET_SDM845 -#define CONFIG_CHIPSET_RESET_HOOK -#define CONFIG_POWER_COMMON -#define CONFIG_POWER_PP5000_CONTROL - -/* NPCX Features */ -#define CONFIG_HIBERNATE_PSL - -/* I2C Ports */ -#define I2C_PORT_BATTERY I2C_PORT_POWER -#define I2C_PORT_CHARGER I2C_PORT_POWER -#define I2C_PORT_ACCEL I2C_PORT_SENSOR -#define I2C_PORT_POWER NPCX_I2C_PORT0_0 -#define I2C_PORT_TCPC0 NPCX_I2C_PORT1_0 -#define I2C_PORT_TCPC1 NPCX_I2C_PORT2_0 -#define I2C_PORT_EEPROM NPCX_I2C_PORT5_0 -#define I2C_PORT_SENSOR NPCX_I2C_PORT7_0 - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -enum power_signal { - SDM845_AP_RST_ASSERTED = 0, - SDM845_PS_HOLD, - SDM845_PMIC_FAULT_L, - SDM845_POWER_GOOD, - SDM845_WARM_RESET, - /* Number of power signals */ - POWER_SIGNAL_COUNT -}; - -enum adc_channel { - ADC_BASE_DET, - ADC_VBUS, - ADC_AMON_BMON, - ADC_PSYS, - ADC_CH_COUNT -}; - -/* Motion sensors */ -enum sensor_id { - LID_ACCEL = 0, - LID_GYRO, - LID_ALS, - SENSOR_COUNT, -}; - -enum pwm_channel { - PWM_CH_DISPLIGHT, - PWM_CH_COUNT -}; - -/* Custom function to indicate if sourcing VBUS */ -int board_is_sourcing_vbus(int port); -/* Enable VBUS sink for a given port */ -int board_vbus_sink_enable(int port, int enable); -/* Reset all TCPCs. */ -void board_reset_pd_mcu(void); -/* Base detection interrupt handler */ -void base_detect_interrupt(enum gpio_signal signal); - -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ALS) - -#endif /* !defined(__ASSEMBLER__) */ - -#endif /* __CROS_EC_BOARD_H */ |