diff options
Diffstat (limited to 'board/coachz/board.c')
-rw-r--r-- | board/coachz/board.c | 161 |
1 files changed, 3 insertions, 158 deletions
diff --git a/board/coachz/board.c b/board/coachz/board.c index c4703dc43c..19b6a24f10 100644 --- a/board/coachz/board.c +++ b/board/coachz/board.c @@ -19,7 +19,6 @@ #include "hooks.h" #include "keyboard_scan.h" #include "lid_switch.h" -#include "ln9310.h" #include "pi3usb9201.h" #include "power.h" #include "power_button.h" @@ -41,12 +40,9 @@ static void usb0_evt(enum gpio_signal signal); static void usb1_evt(enum gpio_signal signal); static void ppc_interrupt(enum gpio_signal signal); static void board_connect_c0_sbu(enum gpio_signal s); -static void switchcap_interrupt(enum gpio_signal signal); #include "gpio_list.h" -static uint8_t sku_id; - /* GPIO Interrupt Handlers */ static void tcpc_alert_event(enum gpio_signal signal) { @@ -105,11 +101,6 @@ static void board_connect_c0_sbu(enum gpio_signal s) hook_call_deferred(&board_connect_c0_sbu_deferred_data, 0); } -static void switchcap_interrupt(enum gpio_signal signal) -{ - ln9310_interrupt(signal); -} - /* ADC channels */ const struct adc_t adc_channels[] = { /* Measure VBUS through a 1/10 voltage divider */ @@ -154,12 +145,6 @@ const struct pwm_t pwm_channels[] = { }; BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT); -/* LN9310 switchcap */ -const struct ln9310_config_t ln9310_config = { - .i2c_port = I2C_PORT_POWER, - .i2c_addr_flags = LN9310_I2C_ADDR_0_FLAGS, -}; - /* Power Path Controller */ struct ppc_config_t ppc_chips[] = { { @@ -343,135 +328,6 @@ void lid_angle_peripheral_enable(int enable) } #endif -static int board_is_clamshell(void) -{ - /* SKU ID of Limozeen: 4, 5 */ - return sku_id == 4 || sku_id == 5; -} - -enum battery_cell_type board_get_battery_cell_type(void) -{ - /* SKU ID of Limozeen: 4, 5 -> 3S battery */ - if (sku_id == 4 || sku_id == 5) - return BATTERY_CELL_TYPE_3S; - - return BATTERY_CELL_TYPE_UNKNOWN; -} - -static void board_update_sensor_config_from_sku(void) -{ - if (board_is_clamshell()) { - motion_sensor_count = 0; - gmr_tablet_switch_disable(); - /* The base accel is not stuffed; don't allow line to float */ - gpio_set_flags(GPIO_ACCEL_GYRO_INT_L, - GPIO_INPUT | GPIO_PULL_DOWN); - } else { - motion_sensor_count = ARRAY_SIZE(motion_sensors); - /* Enable interrupt for the base accel sensor */ - gpio_enable_interrupt(GPIO_ACCEL_GYRO_INT_L); - } -} - -/* Read SKU ID from GPIO and initialize variables for board variants */ -static void sku_init(void) -{ - uint8_t val = 0; - - if (gpio_get_level(GPIO_SKU_ID0)) - val |= 0x01; - if (gpio_get_level(GPIO_SKU_ID1)) - val |= 0x02; - if (gpio_get_level(GPIO_SKU_ID2)) - val |= 0x04; - - sku_id = val; - CPRINTS("SKU: %u", sku_id); - - board_update_sensor_config_from_sku(); -} -DECLARE_HOOK(HOOK_INIT, sku_init, HOOK_PRIO_INIT_I2C + 1); - -static int board_has_ln9310(void) -{ - static int ln9310_present = -1; - int status, val; - - /* Cache the status of LN9310 present or not */ - if (ln9310_present == -1) { - status = i2c_read8(ln9310_config.i2c_port, - ln9310_config.i2c_addr_flags, - LN9310_REG_CHIP_ID, - &val); - - /* - * Any error reading LN9310 CHIP_ID over I2C means the chip - * not present. Fallback to use DA9313 switchcap. - */ - ln9310_present = !status && val == LN9310_CHIP_ID; - } - - return ln9310_present; -} - -static void board_switchcap_init(void) -{ - if (board_has_ln9310()) { - CPRINTS("Use switchcap: LN9310"); - - /* Configure and enable interrupt for LN9310 */ - gpio_set_flags(GPIO_SWITCHCAP_PG_INT_L, GPIO_INT_FALLING); - gpio_enable_interrupt(GPIO_SWITCHCAP_PG_INT_L); - - /* - * Configure LN9310 enable, open-drain output. Don't set the - * level here; otherwise, it will override its value and - * shutdown the switchcap when sysjump to RW. - * - * Note that the gpio.inc configures it GPIO_OUT_LOW. When - * sysjump to RW, will output push-pull a short period of - * time. As it outputs LOW, should be fine. - * - * This GPIO changes like: - * (1) EC boots from RO -> high-Z - * (2) GPIO init according to gpio.inc -> push-pull LOW - * (3) This function configures it -> open-drain HIGH - * (4) Power sequence turns on the switchcap -> open-drain LOW - * (5) EC sysjumps to RW - * (6) GPIO init according to gpio.inc -> push-pull LOW - * (7) This function configures it -> open-drain LOW - */ - gpio_set_flags(GPIO_SWITCHCAP_ON_L, - GPIO_OUTPUT | GPIO_OPEN_DRAIN); - - /* Only configure the switchcap if not sysjump */ - if (!system_jumped_late()) { - /* - * Deassert the enable pin (set it HIGH), so the - * switchcap won't be enabled after the switchcap is - * configured from standby mode to switching mode. - */ - gpio_set_level(GPIO_SWITCHCAP_ON_L, 1); - ln9310_init(); - } - } else { - CPRINTS("Use switchcap: DA9313"); - - /* - * When the chip in power down mode, it outputs high-Z. - * Set pull-down to avoid floating. - */ - gpio_set_flags(GPIO_DA9313_GPIO0, GPIO_INPUT | GPIO_PULL_DOWN); - - /* - * Configure DA9313 enable, push-pull output. Don't set the - * level here; otherwise, it will override its value and - * shutdown the switchcap when sysjump to RW. - */ - gpio_set_flags(GPIO_SWITCHCAP_ON, GPIO_OUTPUT); - } -} - /* Initialize board. */ static void board_init(void) { @@ -488,8 +344,6 @@ static void board_init(void) /* Set the backlight duty cycle to 0. AP will override it later. */ pwm_set_duty(PWM_CH_DISPLIGHT, 0); - - board_switchcap_init(); } DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT); @@ -541,26 +395,17 @@ DECLARE_HOOK(HOOK_CHIPSET_RESUME, board_chipset_resume, HOOK_PRIO_DEFAULT); void board_set_switchcap_power(int enable) { - if (board_has_ln9310()) - gpio_set_level(GPIO_SWITCHCAP_ON_L, !enable); - else - gpio_set_level(GPIO_SWITCHCAP_ON, enable); + gpio_set_level(GPIO_SWITCHCAP_ON, enable); } int board_is_switchcap_enabled(void) { - if (board_has_ln9310()) - return !gpio_get_level(GPIO_SWITCHCAP_ON_L); - else - return gpio_get_level(GPIO_SWITCHCAP_ON); + return gpio_get_level(GPIO_SWITCHCAP_ON); } int board_is_switchcap_power_good(void) { - if (board_has_ln9310()) - return ln9310_power_good(); - else - return gpio_get_level(GPIO_DA9313_GPIO0); + return gpio_get_level(GPIO_DA9313_GPIO0); } void board_reset_pd_mcu(void) |