diff options
Diffstat (limited to 'board/cr50/board.h')
| -rw-r--r-- | board/cr50/board.h | 238 |
1 files changed, 0 insertions, 238 deletions
diff --git a/board/cr50/board.h b/board/cr50/board.h deleted file mode 100644 index 295a6ddf0c..0000000000 --- a/board/cr50/board.h +++ /dev/null @@ -1,238 +0,0 @@ -/* Copyright (c) 2014 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* - * The default watchdog timeout is 1.6 seconds, but there are some legitimate - * flash-intensive TPM operations that actually take close to that long to - * complete. Make sure we don't trigger the watchdog accidentally if the timing - * is just a little off. - */ -#undef CONFIG_WATCHDOG_PERIOD_MS -#define CONFIG_WATCHDOG_PERIOD_MS 5000 - -/* Features that we don't want */ -#undef CONFIG_CMD_LID_ANGLE -#undef CONFIG_CMD_POWERINDEBUG -#undef CONFIG_DMA_DEFAULT_HANDLERS -#undef CONFIG_FMAP -#undef CONFIG_HIBERNATE -#undef CONFIG_LID_SWITCH -#undef CONFIG_CMD_SYSINFO -#undef CONFIG_CMD_SYSJUMP -#undef CONFIG_CMD_SYSLOCK - -#ifndef CR50_DEV -/* Disable stuff that should only be in debug builds */ -#undef CONFIG_CMD_MD -#undef CONFIG_CMD_RW -#undef CONFIG_CMD_SLEEPMASK -#undef CONFIG_CMD_WAITMS -#undef CONFIG_FLASH -#endif - -/* Flash configuration */ -#undef CONFIG_FLASH_PSTATE -/* TODO(crosbug.com/p/44745): Bringup only! Do the right thing for real! */ -#define CONFIG_WP_ALWAYS -/* TODO(crosbug.com/p/44745): For debugging only */ -#define CONFIG_CMD_FLASH - -/* We're using TOP_A for partition 0, TOP_B for partition 1 */ -#define CONFIG_FLASH_NVMEM -/* Offset to start of NvMem area from base of flash */ -#define CONFIG_FLASH_NVMEM_OFFSET_A (CFG_TOP_A_OFF) -#define CONFIG_FLASH_NVMEM_OFFSET_B (CFG_TOP_B_OFF) -/* Address of start of Nvmem area */ -#define CONFIG_FLASH_NVMEM_BASE_A (CONFIG_PROGRAM_MEMORY_BASE + \ - CONFIG_FLASH_NVMEM_OFFSET_A) -#define CONFIG_FLASH_NVMEM_BASE_B (CONFIG_PROGRAM_MEMORY_BASE + \ - CONFIG_FLASH_NVMEM_OFFSET_B) -/* Size partition in NvMem */ -#define NVMEM_PARTITION_SIZE CFG_TOP_SIZE -/* Size in bytes of NvMem area */ -#define CONFIG_FLASH_NVMEM_SIZE (CFG_TOP_SIZE * NVMEM_NUM_PARTITIONS) - - -/* Go to sleep when nothing else is happening */ -#define CONFIG_LOW_POWER_IDLE - -/* Detect the states of other devices */ -#define CONFIG_DEVICE_STATE - -/* Enable debug cable detection */ -#define CONFIG_RDD - -/* USB configuration */ -#define CONFIG_USB -#define CONFIG_USB_CONSOLE -#define CONFIG_USB_I2C -#define CONFIG_USB_INHIBIT_INIT -#define CONFIG_USB_SELECT_PHY -#define CONFIG_USB_SPI -#define CONFIG_USB_SERIALNO -#define DEFAULT_SERIALNO "0" - -#define CONFIG_STREAM_USART -#define CONFIG_STREAM_USB - -/* Enable Case Closed Debugging */ -#define CONFIG_CASE_CLOSED_DEBUG - -#define CONFIG_USB_PID 0x5014 -#define CONFIG_USB_SELF_POWERED - -#undef CONFIG_USB_MAXPOWER_MA -#define CONFIG_USB_MAXPOWER_MA 0 - -/* Enable SPI Master (SPI) module */ -#define CONFIG_SPI_MASTER -#define CONFIG_SPI_MASTER_NO_CS_GPIOS -#define CONFIG_SPI_MASTER_CONFIGURE_GPIOS -#define CONFIG_SPI_FLASH_PORT 0 - -/* Enable SPI Slave (SPS) module */ -#define CONFIG_SPS -#define CONFIG_TPM_SPS - -#define CONFIG_RBOX - -/* We don't need to send events to the AP */ -#undef CONFIG_HOSTCMD_EVENTS - -/* Make most commands restricted */ -#define CONFIG_CONSOLE_COMMAND_FLAGS -#define CONFIG_RESTRICTED_CONSOLE_COMMANDS -#define CONFIG_CONSOLE_COMMAND_FLAGS_DEFAULT CMD_FLAG_RESTRICTED - -/* Include crypto stuff, both software and hardware. */ -#define CONFIG_DCRYPTO - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" - -/* USB string indexes */ -enum usb_strings { - USB_STR_DESC = 0, - USB_STR_VENDOR, - USB_STR_PRODUCT, - USB_STR_VERSION, - USB_STR_CONSOLE_NAME, - USB_STR_BLOB_NAME, - USB_STR_HID_KEYBOARD_NAME, - USB_STR_AP_NAME, - USB_STR_EC_NAME, - USB_STR_UPGRADE_NAME, - USB_STR_SPI_NAME, - USB_STR_SERIALNO, - USB_STR_I2C_NAME, - - USB_STR_COUNT -}; - -/* Device indexes */ -enum device_type { - DEVICE_AP = 0, - DEVICE_EC, - DEVICE_SERVO, - - DEVICE_COUNT -}; - -/* USB SPI device indexes */ -enum usb_spi { - USB_SPI_DISABLE = 0, - USB_SPI_AP, - USB_SPI_EC, -}; - -void board_configure_deep_sleep_wakepins(void); -/* Interrupt handler */ -void sys_rst_asserted(enum gpio_signal signal); -void device_state_on(enum gpio_signal signal); -void post_reboot_request(void); - -/* Special controls over EC and AP */ -void assert_sys_rst(void); -void deassert_sys_rst(void); -int is_sys_rst_asserted(void); -void assert_ec_rst(void); -void deassert_ec_rst(void); -int is_ec_rst_asserted(void); - -#endif /* !__ASSEMBLER__ */ - -/* USB interface indexes (use define rather than enum to expand them) */ -#define USB_IFACE_CONSOLE 0 -#define USB_IFACE_AP 1 -#define USB_IFACE_EC 2 -#define USB_IFACE_UPGRADE 3 -#define USB_IFACE_SPI 4 -#define USB_IFACE_I2C 5 -#define USB_IFACE_COUNT 6 - -/* USB endpoint indexes (use define rather than enum to expand them) */ -#define USB_EP_CONTROL 0 -#define USB_EP_CONSOLE 1 -#define USB_EP_AP 2 -#define USB_EP_EC 3 -#define USB_EP_UPGRADE 4 -#define USB_EP_SPI 5 -#define USB_EP_I2C 6 -#define USB_EP_COUNT 7 - -/* UART indexes (use define rather than enum to expand them) */ -#define UART_CR50 0 -#define UART_AP 1 -#define UART_EC 2 - -#define UARTN UART_CR50 - -/* TODO(crosbug.com/p/56540): Remove this when UART0_RX works everywhere */ -#define GC_UART0_RX_DISABLE - -/* - * This would be a low hanging fruit if there is a need to reduce memory - * footprint. Having a large buffer helps not to drop debug outputs generated - * before console is initialized, but this is not really necessary in a - * production device. - */ -#undef CONFIG_UART_TX_BUF_SIZE -#define CONFIG_UART_TX_BUF_SIZE 4096 - -#define CC_DEFAULT (CC_ALL & ~CC_MASK(CC_TPM)) - -/* Nv Memory users */ -#ifndef __ASSEMBLER__ -enum nvmem_users { - NVMEM_TPM = 0, - NVMEM_CR50, - NVMEM_NUM_USERS -}; -#endif - -/* - * Let's be on the lookout for stack overflow, while debugging. - * - * TODO(vbendeb): remove this before finalizing the code. - */ -#define CONFIG_DEBUG_STACK_OVERFLOW -#define CONFIG_RW_B - -/* Firmware upgrade options. */ -#define CONFIG_NON_HC_FW_UPDATE -#define CONFIG_USB_FW_UPDATE - -#define CONFIG_I2C -#define CONFIG_I2C_MASTER -#define CONFIG_I2C_SLAVE -#define CONFIG_TPM_I2CS - -#define I2C_PORT_MASTER 0 - -#endif /* __CROS_EC_BOARD_H */ |