diff options
Diffstat (limited to 'board/cyan/gpio.inc')
| -rw-r--r-- | board/cyan/gpio.inc | 172 |
1 files changed, 86 insertions, 86 deletions
diff --git a/board/cyan/gpio.inc b/board/cyan/gpio.inc index 06dbf46cd9..44aee47534 100644 --- a/board/cyan/gpio.inc +++ b/board/cyan/gpio.inc @@ -5,91 +5,91 @@ * found in the LICENSE file. */ -GPIO(LID_OPEN, PORT(2), 7, GPIO_INT_BOTH_DSLEEP, lid_interrupt) /* Lid switch */ -GPIO(AC_PRESENT, PORT(3), 0, GPIO_INT_BOTH_DSLEEP, extpower_interrupt) /* BC_ACOK / EC_ACIN - to know if battery or AC connected */ -GPIO(WP_L, PORT(3), 3, GPIO_INT_BOTH, switch_interrupt) /* Write protect input */ -GPIO(POWER_BUTTON_L, PORT(3), 5, GPIO_INT_BOTH_DSLEEP, power_button_interrupt) /* Power button */ -GPIO(RSMRST_L_PGOOD, PORT(6), 3, GPIO_INT_BOTH, power_signal_interrupt) /* RSMRST_N_PWRGD from power logic */ -GPIO(ALL_SYS_PGOOD, PORT(13), 0, GPIO_INT_BOTH_DSLEEP, power_signal_interrupt) /* ALL_SYS_PWRGD from power logic */ -GPIO(PCH_SLP_S4_L, PORT(20), 0, GPIO_INT_BOTH_DSLEEP | GPIO_PULL_UP, power_signal_interrupt) /* SLP_S4# signal from PCH */ -GPIO(PCH_SLP_S3_L, PORT(20), 6, GPIO_INT_BOTH_DSLEEP | GPIO_PULL_UP, power_signal_interrupt) /* SLP_S3# signal from PCH */ - -GPIO(NC_012, PORT(1), 2, GPIO_INPUT | GPIO_PULL_UP, NULL) /* NC */ -GPIO(USB_ILIM_SEL, PORT(1), 3, GPIO_OUT_HIGH, NULL) /* USB current control */ -GPIO(I2C_PORT0_SCL, PORT(1), 5, GPIO_ODR_HIGH, NULL) -GPIO(I2C_PORT0_SDA, PORT(1), 6, GPIO_ODR_HIGH, NULL) - -GPIO(I2C_PORT1_SCL, PORT(2), 2, GPIO_ODR_HIGH, NULL) -GPIO(I2C_PORT1_SDA, PORT(2), 3, GPIO_ODR_HIGH, NULL) -GPIO(PCH_SCI_L, PORT(2), 6, GPIO_ODR_HIGH, NULL) /* SCI output */ - -GPIO(VOLUME_UP, PORT(3), 1, GPIO_INT_FALLING, NULL) /* Volume up button */ -GPIO(VOLUME_DOWN, PORT(3), 4, GPIO_INT_FALLING, NULL) /* Volume down button */ -GPIO(USB2_PWR_EN, PORT(3), 6, GPIO_OUT_HIGH, NULL) /* Enable power for USB2 Port */ - -GPIO(ENTERING_RW, PORT(4), 1, GPIO_OUT_LOW, NULL) /* Indicate when EC is entering RW code */ -GPIO(PCH_SMI_L, PORT(4), 4, GPIO_ODR_HIGH, NULL) /* SMI output */ -GPIO(USB_OC1_L, PORT(4), 5, GPIO_INT_FALLING, NULL) /* DB2 BC1.2 over current signal to EC */ -GPIO(DP_USB_C_HPD_Q, PORT(4), 6, GPIO_OUT_HIGH, NULL) /* DP hot plug detect from EC to SOC */ -GPIO(VBATA_VR_HOT_N, PORT(4), 7, GPIO_INT_FALLING, NULL) /* PROCHOT signal of VBATA VR connected to EC */ - -GPIO(VNN_I2C3_ALERT_N, PORT(5), 0, GPIO_INT_FALLING, NULL) /* Alert signal from VNN VR to EC */ -GPIO(PCH_SUS_STAT_L, PORT(5), 1, GPIO_INT_FALLING, NULL) /* Signal to inform EC that SOC is entering low power state */ -GPIO(TOUCHPANEL_PWREN, PORT(5), 2, GPIO_OUT_HIGH, NULL) /* Enable power for Touch Panel */ -GPIO(TRACKPAD_PWREN, PORT(5), 3, GPIO_OUT_HIGH, NULL) /* Enable power for Track Pad */ -GPIO(USB_OC0_L, PORT(5), 5, GPIO_INT_FALLING, NULL) /* Over current signal of the BC1.2 charger to EC */ -GPIO(EC_ADC0, PORT(5), 6, GPIO_ANALOG, NULL) /* EC_ADC0 */ -GPIO(EC_ADC1, PORT(5), 7, GPIO_ANALOG, NULL) /* EC_ADC1 */ - -GPIO(CHGR_PMON, PORT(6), 0, GPIO_ANALOG, NULL) -GPIO(WIFI_PWREN, PORT(6), 1, GPIO_OUT_HIGH, NULL) /* Enable power for WiFi */ -GPIO(BATT_EN_L, PORT(6), 2, GPIO_INPUT, NULL) /* Will be NC */ -GPIO(SW_OPEN_EC, PORT(6), 4, GPIO_INT_BOTH, NULL) /* Signal from USB Charger to EC to indicate if the isolation switch is open or close */ -GPIO(PCH_SYS_PWROK, PORT(6), 5, GPIO_OUT_LOW, NULL) /* EC thinks everything is up and ready (DELAY_ALL_SYS_PWRGD) */ -GPIO(PCH_WAKE_L, PORT(6), 6, GPIO_ODR_HIGH, NULL) /* PCH wake pin */ -GPIO(USB3_PWR_EN, PORT(6), 7, GPIO_OUT_HIGH, NULL) /* Enable power for USB3 Port */ - -GPIO(USB_CTL1, PORT(10), 5, GPIO_OUT_HIGH, NULL) /* USB charging mode control */ - -GPIO(PCH_RCIN_L, PORT(11), 0, GPIO_ODR_HIGH, NULL) /* Reset line to PCH (for 8042 emulation) */ -GPIO(NC_115, PORT(11), 5, GPIO_INPUT | GPIO_PULL_UP, NULL) /* NC */ - -GPIO(USB_PD_EC_INT, PORT(12), 2, GPIO_INT_BOTH, NULL) /* Interrupt from USB PD Controller to EC */ -GPIO(EC_WAKE_L, PORT(12), 3, GPIO_INT_BOTH_DSLEEP, NULL) -GPIO(USB_CHG_DET_EC, PORT(12), 4, GPIO_INT_BOTH, NULL) /* Signal from USB Charger to EC to indicate charger has been detected */ -GPIO(GYRO_INT2, PORT(12), 7, GPIO_INT_FALLING, NULL) /* Gyro sensor interrupt 2 to EC */ - -GPIO(EC_PLUG_DETECT, PORT(13), 2, GPIO_INT_BOTH, NULL) -GPIO(BAT_LED0_L, PORT(13), 3, GPIO_ODR_HIGH, NULL) /* Battery charging LED - blue */ -GPIO(WWAN_PWREN, PORT(13), 5, GPIO_OUT_HIGH, NULL) /* Enable power for WWAN - PROBE_DETECT_L */ -GPIO(BAT_LED1_L, PORT(13), 6, GPIO_ODR_HIGH, NULL) /* Battery charging LED - orange */ - -GPIO(THERMAL_PROBE_EN_L,PORT(14), 0, GPIO_OUT_HIGH, NULL) -GPIO(PWR_LED0_L, PORT(14), 1, GPIO_ODR_HIGH, NULL) /* Power LED - blue */ -GPIO(PCH_RSMRST_L, PORT(14), 3, GPIO_OUT_LOW, NULL) /* RSMRST_N to PCH */ -GPIO(PWR_LED1_L, PORT(14), 5, GPIO_ODR_HIGH, NULL) /* Power LED - orange */ -GPIO(PVT_CS0, PORT(14), 6, GPIO_ODR_HIGH, NULL) /* SPI PVT Chip select */ -GPIO(ALS_INT, PORT(14), 7, GPIO_INT_FALLING, NULL) /* ALS sensor interrupt to EC */ - -GPIO(WLAN_OFF_L, PORT(15), 0, GPIO_ODR_HIGH, NULL) /* Wireless LAN */ -GPIO(CPU_PROCHOT, PORT(15), 1, GPIO_OUT_LOW, NULL) -GPIO(KBD_IRQ_L, PORT(15), 2, GPIO_ODR_HIGH, NULL) /* Negative edge triggered irq. */ -GPIO(NC_154, PORT(15), 4, GPIO_INPUT | GPIO_PULL_UP, NULL) /* NC */ -GPIO(CORE_PWROK, PORT(15), 5, GPIO_ODR_HIGH, NULL) /* CORE_PWR_OK_R */ -GPIO(LID_OPEN2, PORT(15), 6, GPIO_INT_BOTH_DSLEEP, NULL) /* LID_OPEN_OUT2_R */ -GPIO(PCH_SUSPWRDNACK, PORT(15), 7, GPIO_INT_FALLING, NULL) /* PMC SUSPWRDNACK signal from SOC to EC */ - -GPIO(PCH_PWRBTN_L, PORT(16), 0, GPIO_OUT_HIGH, NULL) /* Power button output to PCH */ -GPIO(GYRO_INT1, PORT(16), 1, GPIO_INT_FALLING, NULL) /* Gyro sensor interrupt 1 to EC */ -GPIO(MUX_CROSS_BAR_EN, PORT(16), 3, GPIO_OUT_LOW, NULL) /* Enable signal of the USB Type C Mux */ - -GPIO(MUX_CROSS_BAR_POL, PORT(20), 1, GPIO_OUT_LOW, NULL) /* Output from EC to POL signal of USB Type C Mux */ -GPIO(EC_BL_DISABLE_L, PORT(20), 2, GPIO_OUT_HIGH, NULL) /* EDP backligh disable signal from EC */ -GPIO(SMC_SHUTDOWN, PORT(20), 3, GPIO_OUT_LOW, NULL) /* Shutdown signal from EC to power sequencing PLD */ -GPIO(MUX_CROSS_BAR_MODE,PORT(20), 4, GPIO_OUT_LOW, NULL) /* Output from EC - Type C Mux mode select */ - -GPIO(SUSPWRDNACK_SOC_EC,PORT(21), 0, GPIO_OUT_LOW, NULL) /* SUSPWRDNACK signal from EC to MOIC device */ -GPIO(PCH_SLP_SX_L, PORT(21), 1, GPIO_INT_BOTH_DSLEEP, NULL) /* Sleep SOIX signal from SOC to EC */ +GPIO_INT(LID_OPEN, PORT(2), 7, GPIO_INT_BOTH_DSLEEP, lid_interrupt) /* Lid switch */ +GPIO_INT(AC_PRESENT, PORT(3), 0, GPIO_INT_BOTH_DSLEEP, extpower_interrupt) /* BC_ACOK / EC_ACIN - to know if battery or AC connected */ +GPIO_INT(WP_L, PORT(3), 3, GPIO_INT_BOTH, switch_interrupt) /* Write protect input */ +GPIO_INT(POWER_BUTTON_L, PORT(3), 5, GPIO_INT_BOTH_DSLEEP, power_button_interrupt) /* Power button */ +GPIO_INT(RSMRST_L_PGOOD, PORT(6), 3, GPIO_INT_BOTH, power_signal_interrupt) /* RSMRST_N_PWRGD from power logic */ +GPIO_INT(ALL_SYS_PGOOD, PORT(13), 0, GPIO_INT_BOTH_DSLEEP, power_signal_interrupt) /* ALL_SYS_PWRGD from power logic */ +GPIO_INT(PCH_SLP_S4_L, PORT(20), 0, GPIO_INT_BOTH_DSLEEP | GPIO_PULL_UP, power_signal_interrupt) /* SLP_S4# signal from PCH */ +GPIO_INT(PCH_SLP_S3_L, PORT(20), 6, GPIO_INT_BOTH_DSLEEP | GPIO_PULL_UP, power_signal_interrupt) /* SLP_S3# signal from PCH */ + +GPIO(NC_012, PORT(1), 2, GPIO_INPUT | GPIO_PULL_UP) /* NC */ +GPIO(USB_ILIM_SEL, PORT(1), 3, GPIO_OUT_HIGH) /* USB current control */ +GPIO(I2C_PORT0_SCL, PORT(1), 5, GPIO_ODR_HIGH) +GPIO(I2C_PORT0_SDA, PORT(1), 6, GPIO_ODR_HIGH) + +GPIO(I2C_PORT1_SCL, PORT(2), 2, GPIO_ODR_HIGH) +GPIO(I2C_PORT1_SDA, PORT(2), 3, GPIO_ODR_HIGH) +GPIO(PCH_SCI_L, PORT(2), 6, GPIO_ODR_HIGH) /* SCI output */ + +GPIO(VOLUME_UP, PORT(3), 1, GPIO_INT_FALLING) /* Volume up button */ +GPIO(VOLUME_DOWN, PORT(3), 4, GPIO_INT_FALLING) /* Volume down button */ +GPIO(USB2_PWR_EN, PORT(3), 6, GPIO_OUT_HIGH) /* Enable power for USB2 Port */ + +GPIO(ENTERING_RW, PORT(4), 1, GPIO_OUT_LOW) /* Indicate when EC is entering RW code */ +GPIO(PCH_SMI_L, PORT(4), 4, GPIO_ODR_HIGH) /* SMI output */ +GPIO(USB_OC1_L, PORT(4), 5, GPIO_INT_FALLING) /* DB2 BC1.2 over current signal to EC */ +GPIO(DP_USB_C_HPD_Q, PORT(4), 6, GPIO_OUT_HIGH) /* DP hot plug detect from EC to SOC */ +GPIO(VBATA_VR_HOT_N, PORT(4), 7, GPIO_INT_FALLING) /* PROCHOT signal of VBATA VR connected to EC */ + +GPIO(VNN_I2C3_ALERT_N, PORT(5), 0, GPIO_INT_FALLING) /* Alert signal from VNN VR to EC */ +GPIO(PCH_SUS_STAT_L, PORT(5), 1, GPIO_INT_FALLING) /* Signal to inform EC that SOC is entering low power state */ +GPIO(TOUCHPANEL_PWREN, PORT(5), 2, GPIO_OUT_HIGH) /* Enable power for Touch Panel */ +GPIO(TRACKPAD_PWREN, PORT(5), 3, GPIO_OUT_HIGH) /* Enable power for Track Pad */ +GPIO(USB_OC0_L, PORT(5), 5, GPIO_INT_FALLING) /* Over current signal of the BC1.2 charger to EC */ +GPIO(EC_ADC0, PORT(5), 6, GPIO_ANALOG) /* EC_ADC0 */ +GPIO(EC_ADC1, PORT(5), 7, GPIO_ANALOG) /* EC_ADC1 */ + +GPIO(CHGR_PMON, PORT(6), 0, GPIO_ANALOG) +GPIO(WIFI_PWREN, PORT(6), 1, GPIO_OUT_HIGH) /* Enable power for WiFi */ +GPIO(BATT_EN_L, PORT(6), 2, GPIO_INPUT) /* Will be NC */ +GPIO(SW_OPEN_EC, PORT(6), 4, GPIO_INT_BOTH) /* Signal from USB Charger to EC to indicate if the isolation switch is open or close */ +GPIO(PCH_SYS_PWROK, PORT(6), 5, GPIO_OUT_LOW) /* EC thinks everything is up and ready (DELAY_ALL_SYS_PWRGD) */ +GPIO(PCH_WAKE_L, PORT(6), 6, GPIO_ODR_HIGH) /* PCH wake pin */ +GPIO(USB3_PWR_EN, PORT(6), 7, GPIO_OUT_HIGH) /* Enable power for USB3 Port */ + +GPIO(USB_CTL1, PORT(10), 5, GPIO_OUT_HIGH) /* USB charging mode control */ + +GPIO(PCH_RCIN_L, PORT(11), 0, GPIO_ODR_HIGH) /* Reset line to PCH (for 8042 emulation) */ +GPIO(NC_115, PORT(11), 5, GPIO_INPUT | GPIO_PULL_UP) /* NC */ + +GPIO(USB_PD_EC_INT, PORT(12), 2, GPIO_INT_BOTH) /* Interrupt from USB PD Controller to EC */ +GPIO(EC_WAKE_L, PORT(12), 3, GPIO_INT_BOTH_DSLEEP) +GPIO(USB_CHG_DET_EC, PORT(12), 4, GPIO_INT_BOTH) /* Signal from USB Charger to EC to indicate charger has been detected */ +GPIO(GYRO_INT2, PORT(12), 7, GPIO_INT_FALLING) /* Gyro sensor interrupt 2 to EC */ + +GPIO(EC_PLUG_DETECT, PORT(13), 2, GPIO_INT_BOTH) +GPIO(BAT_LED0_L, PORT(13), 3, GPIO_ODR_HIGH) /* Battery charging LED - blue */ +GPIO(WWAN_PWREN, PORT(13), 5, GPIO_OUT_HIGH) /* Enable power for WWAN - PROBE_DETECT_L */ +GPIO(BAT_LED1_L, PORT(13), 6, GPIO_ODR_HIGH) /* Battery charging LED - orange */ + +GPIO(THERMAL_PROBE_EN_L,PORT(14), 0, GPIO_OUT_HIGH) +GPIO(PWR_LED0_L, PORT(14), 1, GPIO_ODR_HIGH) /* Power LED - blue */ +GPIO(PCH_RSMRST_L, PORT(14), 3, GPIO_OUT_LOW) /* RSMRST_N to PCH */ +GPIO(PWR_LED1_L, PORT(14), 5, GPIO_ODR_HIGH) /* Power LED - orange */ +GPIO(PVT_CS0, PORT(14), 6, GPIO_ODR_HIGH) /* SPI PVT Chip select */ +GPIO(ALS_INT, PORT(14), 7, GPIO_INT_FALLING) /* ALS sensor interrupt to EC */ + +GPIO(WLAN_OFF_L, PORT(15), 0, GPIO_ODR_HIGH) /* Wireless LAN */ +GPIO(CPU_PROCHOT, PORT(15), 1, GPIO_OUT_LOW) +GPIO(KBD_IRQ_L, PORT(15), 2, GPIO_ODR_HIGH) /* Negative edge triggered irq. */ +GPIO(NC_154, PORT(15), 4, GPIO_INPUT | GPIO_PULL_UP) /* NC */ +GPIO(CORE_PWROK, PORT(15), 5, GPIO_ODR_HIGH) /* CORE_PWR_OK_R */ +GPIO(LID_OPEN2, PORT(15), 6, GPIO_INT_BOTH_DSLEEP) /* LID_OPEN_OUT2_R */ +GPIO(PCH_SUSPWRDNACK, PORT(15), 7, GPIO_INT_FALLING) /* PMC SUSPWRDNACK signal from SOC to EC */ + +GPIO(PCH_PWRBTN_L, PORT(16), 0, GPIO_OUT_HIGH) /* Power button output to PCH */ +GPIO(GYRO_INT1, PORT(16), 1, GPIO_INT_FALLING) /* Gyro sensor interrupt 1 to EC */ +GPIO(MUX_CROSS_BAR_EN, PORT(16), 3, GPIO_OUT_LOW) /* Enable signal of the USB Type C Mux */ + +GPIO(MUX_CROSS_BAR_POL, PORT(20), 1, GPIO_OUT_LOW) /* Output from EC to POL signal of USB Type C Mux */ +GPIO(EC_BL_DISABLE_L, PORT(20), 2, GPIO_OUT_HIGH) /* EDP backligh disable signal from EC */ +GPIO(SMC_SHUTDOWN, PORT(20), 3, GPIO_OUT_LOW) /* Shutdown signal from EC to power sequencing PLD */ +GPIO(MUX_CROSS_BAR_MODE,PORT(20), 4, GPIO_OUT_LOW) /* Output from EC - Type C Mux mode select */ + +GPIO(SUSPWRDNACK_SOC_EC,PORT(21), 0, GPIO_OUT_LOW) /* SUSPWRDNACK signal from EC to MOIC device */ +GPIO(PCH_SLP_SX_L, PORT(21), 1, GPIO_INT_BOTH_DSLEEP) /* Sleep SOIX signal from SOC to EC */ /* Alternate functions GPIO definition */ ALTERNATE(PORT(16), 0x24, 1, MODULE_UART, 0) /* UART0 */ @@ -104,7 +104,7 @@ ALTERNATE(PORT(0), 0xfc, 3, MODULE_KEYBOARD_SCAN, GPIO_KB_OUTPUT) ALTERNATE(PORT(1), 0x03, 3, MODULE_KEYBOARD_SCAN, GPIO_KB_OUTPUT) ALTERNATE(PORT(10) , 0xd8, 3, MODULE_KEYBOARD_SCAN, GPIO_KB_OUTPUT) #ifdef CONFIG_KEYBOARD_COL2_INVERTED - GPIO(KBD_KSO2, PORT(0),1, GPIO_KB_OUTPUT_COL2, NULL) /* Negative edge triggered irq. */ + GPIO(KBD_KSO2, PORT(0),1, GPIO_KB_OUTPUT_COL2) /* Negative edge triggered irq. */ #else ALTERNATE(PORT(0), 0x02, 3, MODULE_KEYBOARD_SCAN, GPIO_KB_OUTPUT_COL2) #endif |