diff options
Diffstat (limited to 'board/dragonegg/gpio.inc')
| -rw-r--r-- | board/dragonegg/gpio.inc | 131 |
1 files changed, 0 insertions, 131 deletions
diff --git a/board/dragonegg/gpio.inc b/board/dragonegg/gpio.inc deleted file mode 100644 index ac46ccbd6f..0000000000 --- a/board/dragonegg/gpio.inc +++ /dev/null @@ -1,131 +0,0 @@ -/* -*- mode:c -*- - * - * Copyright 2018 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Declare symbolic names for all the GPIOs that we care about. - * Note: Those with interrupt handlers must be declared first. */ - -/* Wake Source interrupts */ -GPIO_INT(LID_OPEN, PIN(F, 3), GPIO_INT_BOTH, lid_interrupt) -GPIO_INT(WP_L, PIN(F, 1), GPIO_INT_BOTH, switch_interrupt) /* EC_WP_ODL */ -GPIO_INT(POWER_BUTTON_L, PIN(E, 2), GPIO_INT_BOTH, power_button_interrupt) /* MECH_PWR_BTN_ODL */ -GPIO_INT(ACOK_OD, PIN(E, 3), GPIO_INT_BOTH, extpower_interrupt) -#ifdef CONFIG_LOW_POWER_IDLE -/* Used to wake up the EC from Deep Doze mode when writing to console */ -GPIO_INT(UART1_RX, PIN(B, 0), GPIO_INT_BOTH, uart_deepsleep_interrupt) /* UART_SERVO_TX_EC_RX */ -#endif - -/* Power sequencing interrupts */ -GPIO_INT(SLP_S0_L, PIN(E, 4), GPIO_INT_BOTH, power_signal_interrupt) -#ifndef CONFIG_HOSTCMD_ESPI_VW_SLP_S3 -GPIO_INT(SLP_S3_L, PIN(I, 4), GPIO_INT_BOTH, power_signal_interrupt) -#endif -#ifndef CONFIG_HOSTCMD_ESPI_VW_SLP_S4 -GPIO_INT(SLP_S4_L, PIN(I, 5), GPIO_INT_BOTH, power_signal_interrupt) -#endif -GPIO_INT(SLP_SUS_L, PIN(G, 2), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(PG_EC_RSMRST_ODL,PIN(E, 1), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(PG_EC_DSW_PWROK, PIN(D, 6), GPIO_INT_BOTH, power_signal_interrupt) - -/* USB-C interrupts */ -GPIO_INT(USB_C0_TCPPC_INT_L, PIN(B, 2), GPIO_INT_FALLING, ppc_interrupt) -GPIO_INT(USB_C2_TCPPC_INT_ODL, PIN(L, 1), GPIO_INT_FALLING, ppc_interrupt) -GPIO_INT(USB_C2_TCPC_INT_ODL, PIN(K, 6), GPIO_INT_FALLING, tcpc_alert_event) - -/* Misc. interrupts */ -GPIO_INT(VOLUME_DOWN_L, PIN(I, 6), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(VOLUME_UP_L, PIN(I, 7), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -/* TODO (b:110947310) Uncomment this when sensor task is added to image */ -/* GPIO_INT(BASE_SIXAXIS_INT_L, PIN(J, 0), GPIO_INT_FALLING | GPIO_SEL_1P8V, lsm6dsm_interrupt) */ - -#ifdef CONFIG_HOSTCMD_ESPI -/* enable 1.8v input of EC's espi_reset pin, and then this pin takes effect. */ -GPIO_INT(ESPI_RESET_L, PIN(D, 2), GPIO_INT_FALLING | GPIO_SEL_1P8V, espi_reset_pin_asserted_interrupt) /* eSPI_reset# */ -#endif - -GPIO(SYS_RESET_L, PIN(D, 1), GPIO_ODR_HIGH) /* SYS_RST_ODL */ -GPIO(PCH_WAKE_L, PIN(D, 5), GPIO_ODR_HIGH) /* EC_PCH_WAKE_ODL */ -GPIO(PCH_PWRBTN_L, PIN(B, 6), GPIO_ODR_HIGH) /* EC_PCH_PWR_BTN_ODL */ - -/* Power Sequencing Signals */ -/* - * Both PP5000 and PP3300_TCPC should be powered up whenever the EC is not in - * hibernate mode. They are enabled by default here and disabled in the - * board_hibernate() callback when the EC goes into hibernate mode. - */ -GPIO(EN_PP5000, PIN(K, 5), GPIO_OUT_HIGH) -GPIO(EN_PP3300_TCPC, PIN(E, 6), GPIO_OUT_HIGH) -GPIO(EN_PP3300_A, PIN(C, 5), GPIO_OUT_LOW) -GPIO(EC_PCH_DSW_PWROK, PIN(L, 7), GPIO_OUT_LOW) -GPIO(EC_PCH_RSMRST_L, PIN(H, 0), GPIO_OUT_LOW) -GPIO(EC_PROCHOT_ODL, PIN(D, 0), GPIO_ODR_HIGH) -GPIO(PP5000_PG_OD, PIN(F, 0), GPIO_INPUT) - -/* SYS_PWROK generation is done by the Dialog power good IC */ -UNIMPLEMENTED(PG_EC_ALL_SYS_PWRGD) - -/* USB and USBC Signals */ -GPIO(USB_OC_ODL, PIN(J, 6), GPIO_ODR_HIGH) -GPIO(EN_USB_A_5V, PIN(G, 6), GPIO_OUT_LOW) -GPIO(EN_USB_A_HIGH_POWER, PIN(D, 4), GPIO_OUT_LOW) - -/* BC 1.2 Detection Signals */ -GPIO(USB_C0_BC12_CHG_MAX, PIN(D, 3), GPIO_INPUT) /* C0 BC 1.2 CDP signal */ -GPIO(USB_C1_BC12_CHG_MAX, PIN(B, 7), GPIO_INPUT) /* C1 BC 1.2 CDP signal */ -GPIO(USB_C2_BC12_CHG_MAX, PIN(K, 0), GPIO_INPUT) /* C2 BC 1.2 CDP signal */ -GPIO(USB_C0_BC12_VBUS_ON_ODL, PIN(C, 0), GPIO_ODR_HIGH) /* C0 BC 1.2 enable signal */ -GPIO(USB_C1_BC12_VBUS_ON_ODL, PIN(E, 5), GPIO_ODR_HIGH) /* C1 BC 1.2 enable signal */ -GPIO(USB_C2_BC12_VBUS_ON_ODL, PIN(K, 1), GPIO_ODR_HIGH) /* C2 BC 1.2 enable signal */ - -/* I2C pins - Alternate function below configures I2C module on these pins */ -GPIO(I2C0_SCL, PIN(B, 3), GPIO_INPUT) /* EC_PROG_SCL */ -GPIO(I2C0_SDA, PIN(B, 4), GPIO_INPUT) /* EC_PROG_SDA */ -GPIO(I2C1_SCL, PIN(C, 1), GPIO_INPUT) /* EC_I2C_SENSOR_KB_BL_SCL */ -GPIO(I2C1_SDA, PIN(C, 2), GPIO_INPUT) /* EC_I2C_SENSOR_KB_BL_SDA */ -GPIO(I2C2_SCL, PIN(F, 6), GPIO_INPUT) /* EC_I2C_USB_C1C2_SCL */ -GPIO(I2C2_SDA, PIN(F, 7), GPIO_INPUT) /* EC_I2C_USB_C1C2_SDA */ -GPIO(I2C4_SCL, PIN(E, 0), GPIO_INPUT) /* EC_I2C_USB_C0_SCL */ -GPIO(I2C4_SDA, PIN(E, 7), GPIO_INPUT) /* EC_I2C_USB_C0_SDA */ -GPIO(I2C5_SCL, PIN(A, 4), GPIO_INPUT) /* EC_I2C_POWER_SCL */ -GPIO(I2C5_SDA, PIN(A, 5), GPIO_INPUT) /* EC_I2C_POWER_SDA */ - -GPIO(CCD_MODE_ODL, PIN(H, 5), GPIO_INPUT) /* H1 Case Closed Debug */ -GPIO(CHG_VAP_OTG_EN, PIN(C, 3), GPIO_OUT_LOW) /* Charger VAP/OTG Mode_*/ -GPIO(EC_BATT_PRES_ODL, PIN(H, 3), GPIO_INPUT) -GPIO(ENTERING_RW, PIN(G, 0), GPIO_OUT_LOW) /* EC_ENTERING_RW */ -GPIO(EDP_BKTLEN_OD, PIN(K, 4), GPIO_ODR_LOW) /* Backlight Disable */ -GPIO(KB_BL_EN, PIN(J, 3), GPIO_OUT_LOW) -/* TODO (b:110947310) Convert this to interrupt when senor support is added */ -GPIO(LID_ACCEL_INT_L, PIN(J, 1), GPIO_INPUT | GPIO_SEL_1P8V) - -/* Board ID */ -GPIO(BOARD_VERSION1, PIN(H, 4), GPIO_INPUT) /* Board ID bit0 */ -GPIO(BOARD_VERSION2, PIN(K, 3), GPIO_INPUT) /* Board ID bit1 */ -GPIO(BOARD_VERSION3, PIN(H, 6), GPIO_INPUT) /* Board ID bit2 */ - -/* Fan Control Pins (connected to TP only, set as inputs) */ -GPIO(EC_FAN_TACH1, PIN(J, 2), GPIO_INPUT) -GPIO(EC_FAN_TACH2, PIN(D, 7), GPIO_INPUT) -GPIO(FAN_PWM1, PIN(A, 6), GPIO_INPUT) -GPIO(FAN_PWM2, PIN(A, 7), GPIO_INPUT) - -/* Alternate functions GPIO definitions */ -ALTERNATE(PIN_MASK(B, 0x03), 0, MODULE_UART, 0) /* UART from EC to Servo */ -ALTERNATE(PIN_MASK(B, 0x18), 0, MODULE_I2C, 0) /* I2C0 */ -ALTERNATE(PIN_MASK(C, 0x06), 0, MODULE_I2C, 0) /* I2C1 */ -ALTERNATE(PIN_MASK(F, 0xC0), 0, MODULE_I2C, 0) /* I2C2 */ -ALTERNATE(PIN_MASK(E, 0x81), 0, MODULE_I2C, 0) /* I2C4 */ -ALTERNATE(PIN_MASK(A, 0x30), 0, MODULE_I2C, 0) /* I2C5 */ -/* Charger_IADP -> ADC15, CHARGER_PSYS -> ADC16 */ -ALTERNATE(PIN_MASK(L, 0x0C), 0, MODULE_ADC, 0) -/* Temp sensors 1 -> ADC2, 2 -> ADC3, 3 -> ADC13 */ -ALTERNATE(PIN_MASK(I, 0x0C), 0, MODULE_ADC, 0) -ALTERNATE(PIN_MASK(L, 0x01), 0, MODULE_ADC, 0) -/* Keyboard Backlight Control */ -ALTERNATE(PIN_MASK(A, 0x01), 0, MODULE_PWM, 0) -/* 3 Color LED Control */ -ALTERNATE(PIN_MASK(A, 0x0E), 0, MODULE_PWM, 0) -ALTERNATE(PIN_MASK(I, 0x03), 0, MODULE_ADC, 0) /* ADC1 & ADC0: ADC_USB_C0_VBUS & ADC_USB_C1_VBUS */ |