diff options
Diffstat (limited to 'board/falco/gpio.inc')
| -rw-r--r-- | board/falco/gpio.inc | 122 |
1 files changed, 61 insertions, 61 deletions
diff --git a/board/falco/gpio.inc b/board/falco/gpio.inc index 3356c2ae83..ffb69242fb 100644 --- a/board/falco/gpio.inc +++ b/board/falco/gpio.inc @@ -6,86 +6,86 @@ */ /* Inputs with interrupt handlers are first for efficiency */ -GPIO(POWER_BUTTON_L, A, 2, GPIO_INT_BOTH_DSLEEP, power_button_interrupt) /* Power button */ -GPIO(LID_OPEN, A, 3, GPIO_INT_BOTH_DSLEEP, lid_interrupt) /* Lid switch */ -GPIO(AC_PRESENT, H, 3, GPIO_INT_BOTH_DSLEEP, extpower_interrupt) /* AC power present */ -GPIO(PCH_BKLTEN, M, 3, GPIO_INT_BOTH, backlight_interrupt) /* Backlight enable signal from PCH */ -GPIO(PCH_SLP_S0_L, G, 6, GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S0# signal from PCH */ -GPIO(PCH_SLP_S3_L, G, 7, GPIO_INT_BOTH_DSLEEP, power_signal_interrupt) /* SLP_S3# signal from PCH */ -GPIO(PCH_SLP_S5_L, H, 1, GPIO_INT_BOTH_DSLEEP, power_signal_interrupt) /* SLP_S5# signal from PCH */ -GPIO(PCH_SLP_SUS_L, G, 3, GPIO_INT_BOTH, power_signal_interrupt) /* SLP_SUS# signal from PCH */ -GPIO(PP1050_PGOOD, H, 4, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on 1.05V */ -GPIO(PP1350_PGOOD, H, 6, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on 1.35V (DRAM) */ -GPIO(PP5000_PGOOD, N, 0, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on 5V */ -GPIO(VCORE_PGOOD, C, 6, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on core VR */ -GPIO(PCH_EDP_VDD_EN, J, 1, GPIO_INT_BOTH, lcdvcc_interrupt) /* PCH wants EDP enabled */ -GPIO(RECOVERY_L, A, 5, GPIO_PULL_UP | GPIO_INT_BOTH, switch_interrupt) /* Recovery signal from servo */ -GPIO(WP_L, A, 4, GPIO_INT_BOTH, switch_interrupt) /* Write protect input */ -GPIO(JTAG_TCK, C, 0, GPIO_DEFAULT, jtag_interrupt) /* JTAG clock input */ -GPIO(UART0_RX, A, 0, GPIO_PULL_UP | GPIO_INT_BOTH_DSLEEP, uart_deepsleep_interrupt) /* UART0 RX input */ +GPIO_INT(POWER_BUTTON_L, A, 2, GPIO_INT_BOTH_DSLEEP, power_button_interrupt) /* Power button */ +GPIO_INT(LID_OPEN, A, 3, GPIO_INT_BOTH_DSLEEP, lid_interrupt) /* Lid switch */ +GPIO_INT(AC_PRESENT, H, 3, GPIO_INT_BOTH_DSLEEP, extpower_interrupt) /* AC power present */ +GPIO_INT(PCH_BKLTEN, M, 3, GPIO_INT_BOTH, backlight_interrupt) /* Backlight enable signal from PCH */ +GPIO_INT(PCH_SLP_S0_L, G, 6, GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S0# signal from PCH */ +GPIO_INT(PCH_SLP_S3_L, G, 7, GPIO_INT_BOTH_DSLEEP, power_signal_interrupt) /* SLP_S3# signal from PCH */ +GPIO_INT(PCH_SLP_S5_L, H, 1, GPIO_INT_BOTH_DSLEEP, power_signal_interrupt) /* SLP_S5# signal from PCH */ +GPIO_INT(PCH_SLP_SUS_L, G, 3, GPIO_INT_BOTH, power_signal_interrupt) /* SLP_SUS# signal from PCH */ +GPIO_INT(PP1050_PGOOD, H, 4, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on 1.05V */ +GPIO_INT(PP1350_PGOOD, H, 6, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on 1.35V (DRAM) */ +GPIO_INT(PP5000_PGOOD, N, 0, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on 5V */ +GPIO_INT(VCORE_PGOOD, C, 6, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on core VR */ +GPIO_INT(PCH_EDP_VDD_EN, J, 1, GPIO_INT_BOTH, lcdvcc_interrupt) /* PCH wants EDP enabled */ +GPIO_INT(RECOVERY_L, A, 5, GPIO_PULL_UP | GPIO_INT_BOTH, switch_interrupt) /* Recovery signal from servo */ +GPIO_INT(WP_L, A, 4, GPIO_INT_BOTH, switch_interrupt) /* Write protect input */ +GPIO_INT(JTAG_TCK, C, 0, GPIO_DEFAULT, jtag_interrupt) /* JTAG clock input */ +GPIO_INT(UART0_RX, A, 0, GPIO_PULL_UP | GPIO_INT_BOTH_DSLEEP, uart_deepsleep_interrupt) /* UART0 RX input */ /* Other inputs */ -GPIO(FAN_ALERT_L, B, 0, GPIO_INPUT, NULL) /* From thermal sensor */ -GPIO(PCH_SUSWARN_L, G, 2, GPIO_INT_BOTH, NULL) /* SUSWARN# signal from PCH */ -GPIO(USB1_OC_L, E, 7, GPIO_INPUT, NULL) /* USB port overcurrent warning */ -GPIO(USB2_OC_L, E, 0, GPIO_INPUT, NULL) /* USB port overcurrent warning */ -GPIO(BOARD_VERSION1, Q, 5, GPIO_INPUT, NULL) /* Board version stuffing resistor 1 */ -GPIO(BOARD_VERSION2, Q, 6, GPIO_INPUT, NULL) /* Board version stuffing resistor 2 */ -GPIO(BOARD_VERSION3, Q, 7, GPIO_INPUT, NULL) /* Board version stuffing resistor 3 */ -GPIO(CPU_PGOOD, C, 4, GPIO_INPUT, NULL) /* Power good to the CPU */ +GPIO(FAN_ALERT_L, B, 0, GPIO_INPUT) /* From thermal sensor */ +GPIO(PCH_SUSWARN_L, G, 2, GPIO_INT_BOTH) /* SUSWARN# signal from PCH */ +GPIO(USB1_OC_L, E, 7, GPIO_INPUT) /* USB port overcurrent warning */ +GPIO(USB2_OC_L, E, 0, GPIO_INPUT) /* USB port overcurrent warning */ +GPIO(BOARD_VERSION1, Q, 5, GPIO_INPUT) /* Board version stuffing resistor 1 */ +GPIO(BOARD_VERSION2, Q, 6, GPIO_INPUT) /* Board version stuffing resistor 2 */ +GPIO(BOARD_VERSION3, Q, 7, GPIO_INPUT) /* Board version stuffing resistor 3 */ +GPIO(CPU_PGOOD, C, 4, GPIO_INPUT) /* Power good to the CPU */ /* Outputs; all unasserted by default except for reset signals */ -GPIO(CPU_PROCHOT, B, 1, GPIO_OUT_LOW, NULL) /* Force CPU to think it's overheated */ -GPIO(PP1350_EN, H, 5, GPIO_OUT_LOW, NULL) /* Enable 1.35V supply */ -GPIO(PP3300_DSW_GATED_EN, J, 3, GPIO_OUT_LOW, NULL) /* Enable DSW rails */ -GPIO(PP3300_DX_EN, J, 2, GPIO_OUT_LOW, NULL) /* Enable power to lots of peripherals */ -GPIO(PP3300_LTE_EN, D, 2, GPIO_OUT_LOW, NULL) /* Enable LTE radio */ -GPIO(PP3300_WLAN_EN, J, 0, GPIO_OUT_LOW, NULL) /* Enable WiFi power */ -GPIO(SUSP_VR_EN, C, 7, GPIO_OUT_LOW, NULL) /* Enable 1.05V regulator */ -GPIO(VCORE_EN, C, 5, GPIO_OUT_LOW, NULL) /* Stuffing option - not connected */ -GPIO(PP5000_EN, H, 7, GPIO_OUT_LOW, NULL) /* Enable 5V supply */ -GPIO(SYS_PWROK, H, 2, GPIO_OUT_LOW, NULL) /* EC thinks everything is up and ready */ -GPIO(WLAN_OFF_L, J, 4, GPIO_OUT_LOW, NULL) /* Disable WiFi radio */ -GPIO(CHARGE_L, E, 6, GPIO_OUT_LOW, NULL) /* Allow battery to charge when on AC */ +GPIO(CPU_PROCHOT, B, 1, GPIO_OUT_LOW) /* Force CPU to think it's overheated */ +GPIO(PP1350_EN, H, 5, GPIO_OUT_LOW) /* Enable 1.35V supply */ +GPIO(PP3300_DSW_GATED_EN, J, 3, GPIO_OUT_LOW) /* Enable DSW rails */ +GPIO(PP3300_DX_EN, J, 2, GPIO_OUT_LOW) /* Enable power to lots of peripherals */ +GPIO(PP3300_LTE_EN, D, 2, GPIO_OUT_LOW) /* Enable LTE radio */ +GPIO(PP3300_WLAN_EN, J, 0, GPIO_OUT_LOW) /* Enable WiFi power */ +GPIO(SUSP_VR_EN, C, 7, GPIO_OUT_LOW) /* Enable 1.05V regulator */ +GPIO(VCORE_EN, C, 5, GPIO_OUT_LOW) /* Stuffing option - not connected */ +GPIO(PP5000_EN, H, 7, GPIO_OUT_LOW) /* Enable 5V supply */ +GPIO(SYS_PWROK, H, 2, GPIO_OUT_LOW) /* EC thinks everything is up and ready */ +GPIO(WLAN_OFF_L, J, 4, GPIO_OUT_LOW) /* Disable WiFi radio */ +GPIO(CHARGE_L, E, 6, GPIO_OUT_LOW) /* Allow battery to charge when on AC */ -GPIO(ENABLE_BACKLIGHT, M, 7, GPIO_OUT_LOW, NULL) /* Enable backlight power */ -GPIO(ENABLE_TOUCHPAD, N, 1, GPIO_OUT_LOW, NULL) /* Enable touchpad power */ -GPIO(ENTERING_RW, D, 3, GPIO_OUT_LOW, NULL) /* Indicate when EC is entering RW code */ -GPIO(PCH_DPWROK, G, 0, GPIO_OUT_LOW, NULL) /* Indicate when VccDSW is good */ +GPIO(ENABLE_BACKLIGHT, M, 7, GPIO_OUT_LOW) /* Enable backlight power */ +GPIO(ENABLE_TOUCHPAD, N, 1, GPIO_OUT_LOW) /* Enable touchpad power */ +GPIO(ENTERING_RW, D, 3, GPIO_OUT_LOW) /* Indicate when EC is entering RW code */ +GPIO(PCH_DPWROK, G, 0, GPIO_OUT_LOW) /* Indicate when VccDSW is good */ /* * HDA_SDO is technically an output, but we need to leave it as an * input until we drive it high. So can't use open-drain (HI_Z). */ -GPIO(PCH_HDA_SDO, G, 1, GPIO_INPUT, NULL) /* HDA_SDO signal to PCH; when high, ME ignores security descriptor */ -GPIO(PCH_WAKE_L, F, 0, GPIO_OUT_HIGH, NULL) /* Wake signal from EC to PCH */ -GPIO(PCH_NMI_L, F, 2, GPIO_OUT_HIGH, NULL) /* Non-maskable interrupt pin to PCH */ -GPIO(PCH_PWRBTN_L, H, 0, GPIO_OUT_HIGH, NULL) /* Power button output to PCH */ -GPIO(PCH_PWROK, F, 5, GPIO_OUT_LOW, NULL) /* PWROK / APWROK signals to PCH */ +GPIO(PCH_HDA_SDO, G, 1, GPIO_INPUT) /* HDA_SDO signal to PCH; when high, ME ignores security descriptor */ +GPIO(PCH_WAKE_L, F, 0, GPIO_OUT_HIGH) /* Wake signal from EC to PCH */ +GPIO(PCH_NMI_L, F, 2, GPIO_OUT_HIGH) /* Non-maskable interrupt pin to PCH */ +GPIO(PCH_PWRBTN_L, H, 0, GPIO_OUT_HIGH) /* Power button output to PCH */ +GPIO(PCH_PWROK, F, 5, GPIO_OUT_LOW) /* PWROK / APWROK signals to PCH */ /* * PL6 is one of 4 pins on the EC which can't be used in open-drain * mode. To work around this PCH_RCIN_L is set to an input. It will * only be set to an output when it needs to be driven to 0. */ -GPIO(PCH_RCIN_L, L, 6, GPIO_INPUT, NULL) /* RCIN# line to PCH (for 8042 emulation) */ -GPIO(PCH_RSMRST_L, F, 1, GPIO_OUT_LOW, NULL) /* Reset PCH resume power plane logic */ -GPIO(PCH_SMI_L, F, 4, GPIO_ODR_HIGH, NULL) /* System management interrupt to PCH */ -GPIO(TOUCHSCREEN_RESET_L, N, 7, GPIO_OUT_LOW, NULL) /* Reset touch screen */ -GPIO(EC_EDP_VDD_EN, J, 5, GPIO_OUT_LOW, NULL) /* Enable EDP (passthru from PCH) */ +GPIO(PCH_RCIN_L, L, 6, GPIO_INPUT) /* RCIN# line to PCH (for 8042 emulation) */ +GPIO(PCH_RSMRST_L, F, 1, GPIO_OUT_LOW) /* Reset PCH resume power plane logic */ +GPIO(PCH_SMI_L, F, 4, GPIO_ODR_HIGH) /* System management interrupt to PCH */ +GPIO(TOUCHSCREEN_RESET_L, N, 7, GPIO_OUT_LOW) /* Reset touch screen */ +GPIO(EC_EDP_VDD_EN, J, 5, GPIO_OUT_LOW) /* Enable EDP (passthru from PCH) */ -GPIO(LPC_CLKRUN_L, M, 2, GPIO_ODR_HIGH, NULL) /* Dunno. Probably important, though. */ -GPIO(USB1_ENABLE, E, 4, GPIO_OUT_LOW, NULL) /* USB port 1 output power enable */ -GPIO(USB2_ENABLE, D, 5, GPIO_OUT_LOW, NULL) /* USB port 2 output power enable */ +GPIO(LPC_CLKRUN_L, M, 2, GPIO_ODR_HIGH) /* Dunno. Probably important, though. */ +GPIO(USB1_ENABLE, E, 4, GPIO_OUT_LOW) /* USB port 1 output power enable */ +GPIO(USB2_ENABLE, D, 5, GPIO_OUT_LOW) /* USB port 2 output power enable */ -GPIO(PCH_SUSACK_L, F, 3, GPIO_OUT_HIGH, NULL) /* Acknowledge PCH SUSWARN# signal */ -GPIO(PCH_RTCRST_L, F, 6, GPIO_ODR_HIGH, NULL) /* Not supposed to be here */ -GPIO(PCH_SRTCRST_L, F, 7, GPIO_ODR_HIGH, NULL) /* Not supposed to be here */ +GPIO(PCH_SUSACK_L, F, 3, GPIO_OUT_HIGH) /* Acknowledge PCH SUSWARN# signal */ +GPIO(PCH_RTCRST_L, F, 6, GPIO_ODR_HIGH) /* Not supposed to be here */ +GPIO(PCH_SRTCRST_L, F, 7, GPIO_ODR_HIGH) /* Not supposed to be here */ -GPIO(PWR_LED_L, N, 6, GPIO_OUT_HIGH, NULL) /* Power LED */ -GPIO(KB_LED_EN, D, 4, GPIO_OUT_LOW, NULL) /* Keyboard LED */ -GPIO(BAT_LED0, D, 0, GPIO_OUT_LOW, NULL) /* Battery charger status */ -GPIO(BAT_LED1, D, 1, GPIO_OUT_LOW, NULL) /* Battery charger status */ +GPIO(PWR_LED_L, N, 6, GPIO_OUT_HIGH) /* Power LED */ +GPIO(KB_LED_EN, D, 4, GPIO_OUT_LOW) /* Keyboard LED */ +GPIO(BAT_LED0, D, 0, GPIO_OUT_LOW) /* Battery charger status */ +GPIO(BAT_LED1, D, 1, GPIO_OUT_LOW) /* Battery charger status */ ALTERNATE(A, 0x03, 1, MODULE_UART, GPIO_PULL_UP) /* UART0 */ ALTERNATE(A, 0x40, 3, MODULE_I2C, 0) /* I2C1 SCL */ |