diff options
Diffstat (limited to 'board/gingerbread/board.h')
-rw-r--r-- | board/gingerbread/board.h | 110 |
1 files changed, 0 insertions, 110 deletions
diff --git a/board/gingerbread/board.h b/board/gingerbread/board.h deleted file mode 100644 index cfc5bbf0a0..0000000000 --- a/board/gingerbread/board.h +++ /dev/null @@ -1,110 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Gingerbread board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* Baseboard features */ -#include "baseboard.h" - -/* Optional features */ -/* - * For MP release, CONFIG_SYSTEM_UNLOCKED must be undefined, and - * CONFIG_FLASH_PSTATE_LOCKED must be defined in order to enable write protect - * using option bytes WRP registers. - */ -#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands while in dev. */ -#undef CONFIG_FLASH_PSTATE_LOCKED - - -#define CONFIG_WP_ACTIVE_HIGH - -/* Console */ -#define CONFIG_UART_CONSOLE 3 -#define CONFIG_UART_TX_DMA_CH STM32_DMAC_USART3_TX -#define CONFIG_UART_TX_DMA_PH DMAMUX_REQ_USART3_TX - -/* USB Type C and USB PD defines */ -#define USB_PD_PORT_HOST 0 -#define USB_PD_PORT_DP 1 - -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#define CONFIG_USB_MUX_TUSB1064 -#define CONFIG_USB_PD_VBUS_DETECT_TCPC -#define BOARD_C1_NO_PPC -#define BOARD_C1_1A5_LIMIT - -#define CONFIG_USB_PID 0x5049 -#define CONFIG_USB_BCD_DEV 0x0001 /* v 0.01 */ -#define CONFIG_USB_PD_IDENTITY_HW_VERS 1 -#define CONFIG_USB_PD_IDENTITY_SW_VERS 1 - -/* I2C port names */ -#define I2C_PORT_I2C1 0 -#define I2C_PORT_I2C2 1 -#define I2C_PORT_I2C3 2 -/* Required symbolic I2C port names */ -#define I2C_PORT_MP4245 I2C_PORT_I2C3 -#define I2C_PORT_EEPROM I2C_PORT_I2C1 -#define MP4245_I2C_ADDR_FLAGS MP4245_I2C_ADDR_0_FLAGS - -/* - * Macros for GPIO signals used in common code that don't match the - * schematic names. Signal names in gpio.inc match the schematic and are - * then redefined here to so it's more clear which signal is being used for - * which purpose. - */ -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_WP_L GPIO_EC_WP_L -#define GPIO_WP GPIO_EC_WP_L - -/* Include math_util for bitmask_uint64 used in pd_timers */ -#define CONFIG_MATH_UTIL - -#ifndef __ASSEMBLER__ - -#include "registers.h" - -#define GPIO_DP_HPD GPIO_DDI_MST_IN_HPD -#define GPIO_BPWR_DET GPIO_TP71 -#define GPIO_PWR_BUTTON_RED GPIO_EC_STATUS_LED1 -#define GPIO_PWR_BUTTON_GREEN GPIO_EC_STATUS_LED2 - -#define BUTTON_PRESSED_LEVEL 0 -#define BUTTON_RELEASED_LEVEL 1 - -#define GPIO_TRIGGER_1 GPIO_USB3_A1_CDP_EN -#define GPIO_TRIGGER_2 GPIO_USB3_A2_CDP_EN - -enum debug_gpio { - TRIGGER_1 = 0, - TRIGGER_2, -}; - -/* - * Function used to control GPIO signals as a timing marker. This is intended to - * be used for development/debugging purposes. - * - * @param trigger GPIO debug signal selection - * @param level desired level of the debug gpio signal - * @param pulse_usec pulse width if non-zero - */ -void board_debug_gpio(enum debug_gpio trigger, int level, int pulse_usec); - -/* - * Function called in power on case to enable usbc related interrupts - */ -void board_enable_usbc_interrupts(void); - -/* - * Function called in power off case to disable usbc related interrupts - */ -void board_disable_usbc_interrupts(void); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ |