diff options
Diffstat (limited to 'board/grunt/board.h')
| -rw-r--r-- | board/grunt/board.h | 202 |
1 files changed, 5 insertions, 197 deletions
diff --git a/board/grunt/board.h b/board/grunt/board.h index 64d21ffaa5..56a43db7cc 100644 --- a/board/grunt/board.h +++ b/board/grunt/board.h @@ -8,6 +8,8 @@ #ifndef __CROS_EC_BOARD_H #define __CROS_EC_BOARD_H +#include "baseboard.h" + /* * By default, enable all console messages excepted HC, ACPI and event: * The sensor stack is generating a lot of activity. @@ -16,148 +18,7 @@ #undef CONFIG_HOSTCMD_DEBUG_MODE #define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF -/* Optional features */ -#define CONFIG_HIBERNATE_PSL -#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands. */ - -/* NPCX7 config */ -#define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */ -#define NPCX_TACH_SEL2 0 /* No tach. */ -#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */ - -/* Internal SPI flash on NPCX7 */ -/* Flash is 1MB but reserve half for future use. */ -#define CONFIG_FLASH_SIZE (512 * 1024) -#define CONFIG_SPI_FLASH_REGS -#define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */ - -/* - * Enable 1 slot of secure temporary storage to support - * suspend/resume with read/write memory training. - */ -#define CONFIG_VSTORE -#define CONFIG_VSTORE_SLOT_COUNT 1 - -#define CONFIG_ADC -#define CONFIG_BACKLIGHT_LID -#define CONFIG_BACKLIGHT_LID_ACTIVE_LOW -#define CONFIG_BOARD_VERSION_GPIO -#define CONFIG_HOSTCMD_SKUID -#define CONFIG_I2C -#define CONFIG_I2C_MASTER -#define CONFIG_HOSTCMD_LPC -#define CONFIG_PWM -#define CONFIG_PWM_KBLIGHT -#define CONFIG_TEMP_SENSOR -#define CONFIG_THERMISTOR_NCP15WB -#define CONFIG_VBOOT_HASH -#define CONFIG_VOLUME_BUTTONS - -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_HW_PRESENT_CUSTOM -#define CONFIG_BATTERY_PRESENT_CUSTOM -#define CONFIG_BATTERY_SMART - -#define CONFIG_BC12_DETECT_BQ24392 -#define CONFIG_CHARGER -#define CONFIG_CHARGER_V2 -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_INPUT_CURRENT 128 -#define CONFIG_CHARGER_ISL9238 -#define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 1 -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 -#define CONFIG_CHARGE_RAMP_HW -#define CONFIG_USB_CHARGER - -#define CONFIG_CHIPSET_STONEY -#define CONFIG_CHIPSET_RESET_HOOK -/* - * ACOK from ISL9238 sometimes has a negative pulse after connecting - * USB-C power. We want to ignore it. b/77455171 - */ -#undef CONFIG_EXTPOWER_DEBOUNCE_MS -#define CONFIG_EXTPOWER_DEBOUNCE_MS 200 -#define CONFIG_EXTPOWER_GPIO -#define CONFIG_POWER_COMMON -#define CONFIG_POWER_SHUTDOWN_PAUSE_IN_S5 -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 - -#define CONFIG_KEYBOARD_BOARD_CONFIG -#define CONFIG_KEYBOARD_COL2_INVERTED -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#define CONFIG_KEYBOARD_REFRESH_ROW3 -#define CONFIG_KEYBOARD_IGNORE_REFRESH_BOOT_KEY -#define CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI3 - -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_CMD_PD_CONTROL -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_COMM_LOCKED -#define CONFIG_USB_PD_DISCHARGE_PPC -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT TYPEC_RP_3A0 -#define CONFIG_USB_PD_PORT_COUNT 2 -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_TCPM_ANX3429 -#define CONFIG_USB_PD_TCPM_MUX -#define CONFIG_USB_PD_TCPM_PS8751 -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_TRY_SRC -#define CONFIG_USB_PD_VBUS_DETECT_PPC -#define CONFIG_USBC_PPC_SN5S330 -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_SS_MUX_DFP_ONLY -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP - -/* USB-A config */ -#define CONFIG_USB_PORT_POWER_DUMB -#define USB_PORT_COUNT 2 - -/* TODO(b/69683108): Use correct PD delay values */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ -#define PD_VCONN_SWAP_DELAY 5000 /* us */ - -/* TODO(b/69683178): Use correct PD power values */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 45000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 - -#define I2C_PORT_BATTERY I2C_PORT_POWER -#define I2C_PORT_CHARGER I2C_PORT_POWER -#define I2C_PORT_POWER NPCX_I2C_PORT0_0 -#define I2C_PORT_TCPC0 NPCX_I2C_PORT1_0 -#define I2C_PORT_TCPC1 NPCX_I2C_PORT2_0 -#define I2C_PORT_THERMAL NPCX_I2C_PORT3_0 -#define I2C_PORT_KBLIGHT NPCX_I2C_PORT5_0 -#define I2C_PORT_SENSOR NPCX_I2C_PORT7_0 -/* Accelerometer and Gyroscope are the same device. */ -#define I2C_PORT_ACCEL I2C_PORT_SENSOR - -/* Sensors */ -#define CONFIG_MKBP_EVENT -#define CONFIG_MKBP_USE_HOST_EVENT -#define CONFIG_ACCELGYRO_BMI160 -#define CONFIG_ACCELGYRO_BMI160_INT_EVENT TASK_EVENT_CUSTOM(4) -#define CONFIG_ACCEL_INTERRUPTS -#define CONFIG_ACCEL_KX022 -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_UPDATE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL - -/* Thermal */ -#define CONFIG_TEMP_SENSOR_SB_TSI +#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands while in dev. */ /* Power and battery LEDs */ #define CONFIG_LED_COMMON @@ -175,62 +36,9 @@ #define CONFIG_LED_PWM_COUNT 1 +#define I2C_PORT_KBLIGHT NPCX_I2C_PORT5_0 + /* KB backlight driver */ #define CONFIG_LED_DRIVER_LM3630A -/* FIFO size is a power of 2. */ -#define CONFIG_ACCEL_FIFO 1024 /* TODO(teravest): Check this value. */ - -/* Depends on how fast the AP boots and typical ODRs. */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO / 3) - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -enum adc_channel { - ADC_TEMP_SENSOR_CHARGER, - ADC_TEMP_SENSOR_SOC, - ADC_VBUS, - ADC_SKU_ID1, - ADC_SKU_ID2, - ADC_CH_COUNT -}; - -enum power_signal { - X86_SLP_S3_N, - X86_SLP_S5_N, - X86_S0_PGOOD, - X86_S5_PGOOD, - POWER_SIGNAL_COUNT -}; - -enum temp_sensor_id { - TEMP_SENSOR_CHARGER = 0, - TEMP_SENSOR_SOC, - TEMP_SENSOR_CPU, - TEMP_SENSOR_COUNT -}; - -enum pwm_channel { - PWM_CH_KBLIGHT = 0, - PWM_CH_LED1_AMBER, - PWM_CH_LED2_BLUE, - PWM_CH_COUNT -}; - -enum sensor_id { - LID_ACCEL, - BASE_ACCEL, - BASE_GYRO, -}; - -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK (1 << LID_ACCEL) - -void board_reset_pd_mcu(void); - -#endif /* !__ASSEMBLER__ */ - #endif /* __CROS_EC_BOARD_H */ |