diff options
Diffstat (limited to 'board/hammer/gpio.inc')
| -rw-r--r-- | board/hammer/gpio.inc | 30 |
1 files changed, 25 insertions, 5 deletions
diff --git a/board/hammer/gpio.inc b/board/hammer/gpio.inc index 3b16f643ef..1b60a32100 100644 --- a/board/hammer/gpio.inc +++ b/board/hammer/gpio.inc @@ -36,8 +36,13 @@ GPIO_INT(KB_IN07, PIN(B, 15), GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) /* Do not forget to update KB_OUT_PORT_LIST to match this. */ GPIO(KB_OUT00, PIN(B, 1), GPIO_KB_OUTPUT) GPIO(KB_OUT01, PIN(A, 5), GPIO_KB_OUTPUT) +#ifdef BOARD_WAND +GPIO(KB_OUT02, PIN(A, 8), GPIO_KB_OUTPUT) +GPIO(KB_OUT03, PIN(B, 4), GPIO_KB_OUTPUT) +#else GPIO(KB_OUT02, PIN(A, 3), GPIO_KB_OUTPUT) GPIO(KB_OUT03, PIN(A, 2), GPIO_KB_OUTPUT) +#endif GPIO(KB_OUT04, PIN(A, 6), GPIO_KB_OUTPUT) GPIO(KB_OUT05, PIN(A, 0), GPIO_KB_OUTPUT) GPIO(KB_OUT06, PIN(A, 1), GPIO_KB_OUTPUT) @@ -50,8 +55,8 @@ GPIO(KB_OUT12, PIN(C, 13), GPIO_KB_OUTPUT) /* I2C pins should be configured as inputs until I2C module is */ /* initialized. This will avoid driving the lines unintentionally.*/ -GPIO(MASTER_I2C_SCL, PIN(B, 6), GPIO_INPUT) -GPIO(MASTER_I2C_SDA, PIN(B, 7), GPIO_INPUT) +GPIO(TOUCHPAD_I2C_SCL, PIN(B, 6), GPIO_INPUT) +GPIO(TOUCHPAD_I2C_SDA, PIN(B, 7), GPIO_INPUT) /* TODO(crosbug.com/p/59083): Disable trackpad when appropriate */ #ifdef BOARD_WHISKERS GPIO(EN_PP3300_TP, PIN(A, 14), GPIO_OUT_HIGH) @@ -67,19 +72,34 @@ GPIO(KEYBOARD_BACKLIGHT, PIN(B, 9), GPIO_INPUT) GPIO(WP_L, PIN(A, 13), GPIO_INPUT | GPIO_PULL_UP) -GPIO(BASE_DET, PIN(A, 15), GPIO_INPUT) - #ifdef BOARD_WHISKERS GPIO(TP_BOOT0, PIN(B, 4), GPIO_INPUT) GPIO(TP_RESET, PIN(B, 5), GPIO_INPUT) #endif +#ifdef BOARD_WAND +GPIO(BASE_UART_TX_RX, PIN(A, 2), GPIO_ODR_HIGH | GPIO_PULL_UP) + +GPIO(CHARGER_I2C_SCL, PIN(B, 10), GPIO_INPUT) +GPIO(CHARGER_I2C_SDA, PIN(B, 11), GPIO_INPUT) + +GPIO(SWITCH_STATUS, PIN(A, 15), GPIO_INPUT) +GPIO(EN_OTG, PIN(B, 5), GPIO_INPUT) +#else +GPIO(BASE_DET, PIN(A, 15), GPIO_INPUT) +#endif + /* Unimplemented signals since we are not an EC */ UNIMPLEMENTED(ENTERING_RW) ALTERNATE(PIN_MASK(A, 0x0600), 1, MODULE_UART, GPIO_PULL_UP) /* USART1: PA09/PA10 - Servo stm32 console UART */ -ALTERNATE(PIN_MASK(B, 0x00c0), 1, MODULE_I2C, 0) /* I2C MASTER:PB6/7 GPIO_ODR_HIGH */ +#ifdef BOARD_WAND +ALTERNATE(PIN_MASK(A, 0x0004), 1, MODULE_UART, GPIO_ODR_HIGH) /* USART2: PA2 - EC-EC UART */ +ALTERNATE(PIN_MASK(B, 0x0c00), 1, MODULE_I2C, 0) /* I2C CHARGER: PB10/11 GPIO_ODR_HIGH */ +#endif + +ALTERNATE(PIN_MASK(B, 0x00c0), 1, MODULE_I2C, 0) /* I2C TOUCHPAD: PB6/7 GPIO_ODR_HIGH */ #ifdef BOARD_WHISKERS ALTERNATE(PIN_MASK(B, 0x0100), 2, MODULE_PWM, GPIO_PULL_DOWN) /* PWM: PB8 */ |