diff options
Diffstat (limited to 'board/hatch/board.h')
-rw-r--r-- | board/hatch/board.h | 178 |
1 files changed, 0 insertions, 178 deletions
diff --git a/board/hatch/board.h b/board/hatch/board.h deleted file mode 100644 index 057475cb55..0000000000 --- a/board/hatch/board.h +++ /dev/null @@ -1,178 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Hatch board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* Baseboard features */ -#include "baseboard.h" - -#define CONFIG_POWER_BUTTON -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#define CONFIG_LED_COMMON -#define CONFIG_LOW_POWER_IDLE - -#define CONFIG_HOSTCMD_ESPI - -#undef CONFIG_UART_TX_BUF_SIZE -#define CONFIG_UART_TX_BUF_SIZE 4096 - -/* Keyboard features */ -#define CONFIG_PWM_KBLIGHT - -/* Sensors */ -/* BMI160 Base accel/gyro */ -#define CONFIG_ACCEL_INTERRUPTS -#define CONFIG_ACCELGYRO_BMI160 -#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) -#define CONFIG_ACCELGYRO_BMI160_INT2_OUTPUT -/* BMA253 Lid accel */ -#define CONFIG_ACCEL_BMA255 -#define CONFIG_ACCEL_FORCE_MODE_MASK (BIT(LID_ACCEL) | BIT(CLEAR_ALS)) -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL -#define CONFIG_LID_ANGLE_UPDATE -/* TC3400 ALS */ -#define CONFIG_ALS -#define ALS_COUNT 1 -#define CONFIG_ALS_TCS3400 -#define CONFIG_ALS_TCS3400_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(CLEAR_ALS) -#define I2C_PORT_ALS I2C_PORT_SENSOR - -/* USB Type C and USB PD defines */ -#define CONFIG_USB_PD_COMM_LOCKED -#define CONFIG_USB_PD_TCPM_ANX7447 -#define CONFIG_USB_PD_TCPM_ANX7447_AUX_PU_PD -#define CONFIG_USB_PD_TCPM_PS8751 -#define BOARD_TCPC_C0_RESET_HOLD_DELAY ANX74XX_RESET_HOLD_MS -#define BOARD_TCPC_C0_RESET_POST_DELAY ANX74XX_RESET_HOLD_MS -#define BOARD_TCPC_C1_RESET_HOLD_DELAY PS8XXX_RESET_DELAY_MS -#define BOARD_TCPC_C1_RESET_POST_DELAY 0 -#define GPIO_USB_C1_TCPC_RST GPIO_USB_C1_TCPC_RST_ODL - -/* USB Type A Features */ -#define CONFIG_USB_PORT_POWER_SMART -#undef CONFIG_USB_PORT_POWER_SMART_PORT_COUNT -#define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 1 -#define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY -#define GPIO_USB1_ILIM_SEL GPIO_EN_USB_A_LOW_PWR_OD - -/* BC 1.2 */ -#define CONFIG_BC12_DETECT_PI3USB9201 - -/* Charger features */ -/* - * The IDCHG current limit is set in 512 mA steps. The value set here is - * somewhat specific to the battery pack being currently used. The limit here - * was set based on the battery's discharge current limit and what was tested to - * prevent the AP rebooting with low charge level batteries. - * - * TODO(b/133447140): Revisit this threshold once peak power consumption tuning - * for the AP is completed. - */ -#define CONFIG_CHARGER_BQ25710_IDCHG_LIMIT_MA 8192 - -/* Volume Button feature */ -#define CONFIG_CMD_BUTTON -#define CONFIG_VOLUME_BUTTONS -#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL -#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL - -/* Fan features */ -#define CONFIG_FANS 1 -#undef CONFIG_FAN_INIT_SPEED -#define CONFIG_FAN_INIT_SPEED 50 -#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_EN_A_RAILS -#define CONFIG_THERMISTOR -#define CONFIG_THROTTLE_AP -#define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B - -/* MST */ -/* - * TDOD (b/124068003): This inherently assumes the MST chip is connected to only - * one Type C port. This will need to be chagned to support 2 Type C ports - * connected to the same MST chip. - */ -#define USB_PD_PORT_TCPC_MST USB_PD_PORT_TCPC_1 - -/* - * Macros for GPIO signals used in common code that don't match the - * schematic names. Signal names in gpio.inc match the schematic and are - * then redefined here to so it's more clear which signal is being used for - * which purpose. - */ -#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L -#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L -#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_RSMRST_L_PGOOD GPIO_PG_EC_RSMRST_L -#define GPIO_PCH_SYS_PWROK GPIO_EC_PCH_SYS_PWROK -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GPIO_PCH_SLP_S4_L GPIO_SLP_S4_L -#define GPIO_EN_PP5000 GPIO_EN_PP5000_A - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -/* GPIO signals updated base on board version. */ -#define GPIO_EN_PP5000_A gpio_en_pp5000_a -extern enum gpio_signal gpio_en_pp5000_a; - -enum adc_channel { - ADC_TEMP_SENSOR_1, /* ADC0 */ - ADC_TEMP_SENSOR_2, /* ADC1 */ - ADC_CH_COUNT -}; - -enum sensor_id { - LID_ACCEL = 0, - BASE_ACCEL, - BASE_GYRO, - CLEAR_ALS, - RGB_ALS, - SENSOR_COUNT, -}; - -enum pwm_channel { - PWM_CH_KBLIGHT, - PWM_CH_FAN, - PWM_CH_COUNT -}; - -enum fan_channel { - FAN_CH_0 = 0, - /* Number of FAN channels */ - FAN_CH_COUNT, -}; - -enum mft_channel { - MFT_CH_0 = 0, - /* Number of MFT channels */ - MFT_CH_COUNT, -}; - -enum temp_sensor_id { - TEMP_SENSOR_1, - TEMP_SENSOR_2, - TEMP_SENSOR_COUNT -}; - -/* List of possible batteries */ -enum battery_type { - BATTERY_SMP_LIS, - BATTERY_SMP_SDI, - BATTERY_TYPE_COUNT, -}; - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ |