diff options
Diffstat (limited to 'board/kahlee/board.h')
| -rw-r--r-- | board/kahlee/board.h | 299 |
1 files changed, 299 insertions, 0 deletions
diff --git a/board/kahlee/board.h b/board/kahlee/board.h new file mode 100644 index 0000000000..7c8b790899 --- /dev/null +++ b/board/kahlee/board.h @@ -0,0 +1,299 @@ +/* Copyright 2017 The Chromium OS Authors. All rights reserved. + * Use of this source code is governed by a BSD-style license that can be + * found in the LICENSE file. + */ + +/* Kahlee board configuration */ + +#ifndef __CROS_EC_BOARD_H +#define __CROS_EC_BOARD_H + +/* + * By default, enable all console messages excepted HC, ACPI and event: + * The sensor stack is generating a lot of activity. + */ +#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC))) +#undef CONFIG_HOSTCMD_DEBUG_MODE +#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF + +/* EC console commands */ +#define CONFIG_CMD_ACCELS +#define CONFIG_CMD_ACCEL_INFO +#define CONFIG_CMD_BATT_MFG_ACCESS +#define CONFIG_CHARGER_SENSE_RESISTOR 10 +#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 +#define CONFIG_CMD_CHARGER_PSYS + +/* Battery */ +#define CONFIG_BATTERY_DEVICE_CHEMISTRY "LION" +#define CONFIG_BATTERY_CUT_OFF +#define CONFIG_BATTERY_PRESENT_CUSTOM +#define CONFIG_BATTERY_SMART + +/* Charger */ +#define CONFIG_CHARGE_MANAGER +#define CONFIG_CHARGE_RAMP +#define CONFIG_CHARGER +#define CONFIG_CHARGER_V2 +#define CONFIG_CHARGER_ISL9237 +#define CONFIG_CHARGER_DISCHARGE_ON_AC +#define CONFIG_CHARGER_INPUT_CURRENT 2137 +#undef CONFIG_CHARGER_LIMIT_POWER_THRESH_BAT_PCT +#undef CONFIG_CHARGER_LIMIT_POWER_THRESH_CHG_MW +#undef CONFIG_CHARGER_MAINTAIN_VBAT +#define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 1 +#define CONFIG_USB_CHARGER +#undef CONFIG_CHARGER_PROFILE_OVERRIDE +#undef CONFIG_CHARGER_PROFILE_OVERRIDE_COMMON +#define CONFIG_CHARGE_MANAGER_EXTERNAL_POWER_LIMIT + +/* USB-A config */ +#define CONFIG_USB_PORT_POWER_SMART +#define CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE USB_CHARGE_MODE_CDP +#define CONFIG_USB_PORT_POWER_SMART_SIMPLE +#undef CONFIG_USB_PORT_POWER_SMART_PORT_COUNT +#define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 1 +#define GPIO_USB_ILIM_SEL GPIO_USB_A_CHARGE_EN_L +#define GPIO_USB_CTL1 GPIO_USB_A_CHARGE_EN_L + +/* USB PD config */ +#define CONFIG_CASE_CLOSED_DEBUG_EXTERNAL +#define CONFIG_CMD_PD_CONTROL +#define CONFIG_USB_PD_ALT_MODE +#define CONFIG_USB_PD_ALT_MODE_DFP +#define CONFIG_USB_PD_CUSTOM_VDM +#define CONFIG_USB_PD_DUAL_ROLE +#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE +#define CONFIG_USB_PD_DISCHARGE +#define CONFIG_USB_PD_DISCHARGE_TCPC +#define CONFIG_USB_PD_LOGGING +#define CONFIG_USB_PD_LOG_SIZE 512 +#define CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT TYPEC_RP_3A0 +#define CONFIG_USB_PD_PORT_COUNT 2 +#define CONFIG_USB_PD_QUIRK_SLOW_CC_STATUS +#undef CONFIG_USB_PD_VBUS_DETECT_CHARGER +#define ADC_VBUS -1 +#define CONFIG_USB_PD_TCPC_LOW_POWER +#define CONFIG_USB_PD_TCPC_FW_VERSION +#define CONFIG_USB_PD_TCPM_MUX +#define CONFIG_USB_PD_TCPM_PS8751 +#define CONFIG_USB_PD_TCPM_TCPCI +#define CONFIG_USB_PD_TRY_SRC +#define CONFIG_USB_POWER_DELIVERY +#define CONFIG_USB_PD_COMM_LOCKED + +#define CONFIG_USBC_SS_MUX +#define CONFIG_USBC_SS_MUX_DFP_ONLY +#define CONFIG_USBC_VCONN +#define CONFIG_USBC_VCONN_SWAP + +/* SoC / PCH */ +#define CONFIG_LPC +#define CONFIG_CHIPSET_STONEY +#define CONFIG_CHIPSET_RESET_HOOK +#define CONFIG_POWER_BUTTON +#define CONFIG_POWER_BUTTON_X86 +#define CONFIG_POWER_COMMON +#define CONFIG_POWER_SHUTDOWN_PAUSE_IN_S5 +#define GPIO_PCH_WAKE_L 0 + +/* EC */ +#define CONFIG_ADC +#define CONFIG_BOARD_VERSION +#define CONFIG_BOARD_SPECIFIC_VERSION +#undef CONFIG_BUTTON_COUNT +#define CONFIG_EXTPOWER_GPIO +#undef CONFIG_EXTPOWER_DEBOUNCE_MS +#define CONFIG_EXTPOWER_DEBOUNCE_MS 1000 +#define CONFIG_FPU +#define CONFIG_HOSTCMD_FLASH_SPI_INFO +#define CONFIG_I2C +#define CONFIG_I2C_MASTER +#define CONFIG_KEYBOARD_BOARD_CONFIG +#define CONFIG_KEYBOARD_PROTOCOL_8042 +#define CONFIG_KEYBOARD_COL2_INVERTED +#define CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI2 +#define CONFIG_LED_COMMON +#define CONFIG_LID_SWITCH +#define CONFIG_LOW_POWER_IDLE +#define CONFIG_LTO +#define CONFIG_POWER_SIGNAL_INTERRUPT_STORM_DETECT_THRESHOLD 30 +#define CONFIG_PWM +#define CONFIG_FANS 1 +#define CONFIG_TEMP_SENSOR +#define CONFIG_TEMP_SENSOR_G781 +#define CONFIG_SCI_GPIO GPIO_PCH_SCI_L +#define CONFIG_UART_HOST 0 +#define CONFIG_VBOOT_HASH +#define CONFIG_BACKLIGHT_LID +#define CONFIG_WIRELESS +#define CONFIG_WIRELESS_SUSPEND EC_WIRELESS_SWITCH_WLAN_POWER +#define CONFIG_WLAN_POWER_ACTIVE_LOW +#define WIRELESS_GPIO_WLAN_POWER GPIO_WIRELESS_GPIO_WLAN_POWER +#define CONFIG_USB_SWITCH_PI3USB9281 +#define CONFIG_USB_SWITCH_PI3USB9281_CHIP_COUNT 2 + +/* + * During shutdown sequence TPS65094x PMIC turns off the sensor rails + * asynchronously to the EC. If we access the sensors when the sensor power + * rails are off we get I2C errors. To avoid this issue, defer switching + * the sensors rate if in S3. By the time deferred function is serviced if + * the chipset is in S5 we can back out from switching the sensor rate. + * + * Time taken by V1P8U rail to go down from S3 is 30ms to 60ms hence defer + * the sensor switching after 60ms. + */ +#undef CONFIG_MOTION_SENSE_SUSPEND_DELAY_US +#define CONFIG_MOTION_SENSE_SUSPEND_DELAY_US (MSEC * 60) + +#define CONFIG_FLASH_SIZE 524288 +#define CONFIG_SPI_FLASH_REGS +#define CONFIG_SPI_FLASH_W25X40 + +/* + * Enable 1 slot of secure temporary storage to support + * suspend/resume with read/write memory training. + */ +#define CONFIG_VSTORE +#define CONFIG_VSTORE_SLOT_COUNT 1 + +/* Optional feature - used by nuvoton */ +#define NPCX_UART_MODULE2 1 /* 0:GPIO10/11 1:GPIO64/65 as UART */ +#define NPCX_JTAG_MODULE2 0 /* 0:GPIO21/17/16/20 1:GPIOD5/E2/D4/E5 as JTAG*/ +#define NPCX_TACH_SEL2 1 /* 0:GPIO40/A4 1:GPIO93/D3 as TACH */ + +/* I2C ports */ +#define I2C_PORT_THERMAL NPCX_I2C_PORT1 +#define I2C_PORT_GYRO NPCX_I2C_PORT2 +#define I2C_PORT_LID_ACCEL NPCX_I2C_PORT2 +#define I2C_PORT_ALS NPCX_I2C_PORT2 +#define I2C_PORT_BARO NPCX_I2C_PORT2 +#define I2C_PORT_BATTERY NPCX_I2C_PORT3 +#define I2C_PORT_CHARGER NPCX_I2C_PORT3 +/* Accelerometer and Gyroscope are the same device. */ +#define I2C_PORT_ACCEL I2C_PORT_GYRO + +/* Sensors */ +#define CONFIG_MKBP_EVENT +#define CONFIG_MKBP_USE_HOST_EVENT +#define CONFIG_ACCEL_KXCJ9 +#define CONFIG_ALS_AL3010 +#define AL3010_I2C_ADDR AL3010_I2C_ADDR1 +#undef CONFIG_LID_ANGLE +#undef CONFIG_LID_ANGLE_UPDATE +#undef CONFIG_LID_ANGLE_SENSOR_BASE +#undef CONFIG_LID_ANGLE_SENSOR_LID + +/* FIFO size is in power of 2. */ +#define CONFIG_ACCEL_FIFO 1024 + +/* Depends on how fast the AP boots and typical ODRs */ +#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO / 3) + + +#ifndef __ASSEMBLER__ + +#include "gpio_signal.h" +#include "registers.h" + +/* ADC signal */ +enum adc_channel { + ADC_IMON1, /* ADC0 */ + ADC_IMON2, /* ADC1 */ + ADC_BOARD_ID, /* ADC2 */ + ADC_CH_COUNT +}; + +enum pwm_channel { + PWM_CH_FAN, + /* Number of PWM channels */ + PWM_CH_COUNT +}; + +enum fan_channel { + FAN_CH_0, + /* Number of FAN channels */ + FAN_CH_COUNT +}; + +enum mft_channel { + MFT_CH_0, + /* Number of MFT channels */ + MFT_CH_COUNT +}; + +enum power_signal { + X86_SLP_S3_N = 0, + X86_SLP_S5_N, + X86_SPOK, + X86_ALW_PG, + + /* Number of X86 signals */ + POWER_SIGNAL_COUNT +}; + +enum temp_sensor_id { + TEMP_SENSOR_I2C_G781_LOCAL = 0, + TEMP_SENSOR_I2C_G781_REMOTE1, + TEMP_SENSOR_BATTERY, + TEMP_SENSOR_COUNT +}; + +/* Light sensors */ +enum als_id { + ALS_AL3010 = 0, + + ALS_COUNT +}; + +/* + * Motion sensors: + * When reading through IO memory is set up for sensors (LPC is used), + * the first 2 entries must be accelerometers, then gyroscope. + * For BMI160, accel, gyro and compass sensors must be next to each other. + */ +enum sensor_id { + LID_ACCEL = 0, +}; + +enum board_version { + BOARD_VERSION_UNKNOWN = -1, + BOARD_VERSION_1, + BOARD_VERSION_2, + BOARD_VERSION_3, + BOARD_VERSION_4, + BOARD_VERSION_5, + BOARD_VERSION_6, + BOARD_VERSION_7, + BOARD_VERSION_8, + BOARD_VERSION_COUNT, +}; + +/* TODO: determine the following board specific type-C power constants */ +/* FIXME(dhendrix): verify all of the below PD_* numbers */ +/* + * delay to turn on the power supply max is ~16ms. + * delay to turn off the power supply max is about ~180ms. + */ +#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ +#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ + +/* delay to turn on/off vconn */ +#define PD_VCONN_SWAP_DELAY 5000 /* us */ + +/* Define typical operating power and max power */ +#define PD_OPERATING_POWER_MW 15000 +#define PD_MAX_POWER_MW 45000 +#define PD_MAX_CURRENT_MA 3000 +#define PD_MAX_VOLTAGE_MV 20000 + +/* Reset PD MCU */ +void board_reset_pd_mcu(void); + +int board_get_version(void); + +void board_print_tcpc_fw_version(int port); + +#endif /* !__ASSEMBLER__ */ + +#endif /* __CROS_EC_BOARD_H */ |