diff options
Diffstat (limited to 'board/kano/gpio.inc')
| -rw-r--r-- | board/kano/gpio.inc | 40 |
1 files changed, 1 insertions, 39 deletions
diff --git a/board/kano/gpio.inc b/board/kano/gpio.inc index 79a97b0475..2991583124 100644 --- a/board/kano/gpio.inc +++ b/board/kano/gpio.inc @@ -28,47 +28,9 @@ */ GPIO(EC_KSO_02_INV, PIN(1, 7), GPIO_OUT_LOW) -/* - * GPIOE1 is an ALT function ADC INPUT on board ID 2 and a GPIO INPUT on - * board ID 1. This declaration gives us a signal name to use on board - * ID 1. - */ -GPIO(ID_1_EC_BATT_PRES_ODL, PIN(E, 1), GPIO_INPUT) - -/* - * GPIO34 is an INPUT on board ID 2 and ODR_LOW on board ID 1. - * - * Since this pin is pulled up to 3.3V through a 30.9K ohm resistor on - * board ID 2, we will leak about 0.3mW until the pin is put in ALT mode - * when MODULE_ADC configuration runs. Initializing the pin to ODR_LOW - * gives us full control on both boards. - */ -GPIO(ID_1_USB_C0_C2_TCPC_RST_ODL, PIN(3, 4), GPIO_ODR_LOW) - -/* Board ID 1 IO expander configuration */ - -IOEX(ID_1_USB_C0_RT_RST_ODL, EXPIN(IOEX_ID_1_C0_NCT38XX, 0, 2), GPIO_ODR_LOW) -/* GPIO03_P1 to PU */ -IOEX(ID_1_USB_C0_FRS_EN, EXPIN(IOEX_ID_1_C0_NCT38XX, 0, 4), GPIO_LOW) -IOEX(ID_1_USB_C0_OC_ODL, EXPIN(IOEX_ID_1_C0_NCT38XX, 0, 6), GPIO_ODR_HIGH) -/* GPIO07_P1 to PU */ - -IOEX(ID_1_USB_C2_RT_RST_ODL, EXPIN(IOEX_ID_1_C2_NCT38XX, 0, 2), GPIO_ODR_LOW) -/* GPIO03_P2 to PU */ -IOEX(ID_1_USB_C2_FRS_EN, EXPIN(IOEX_ID_1_C2_NCT38XX, 0, 4), GPIO_LOW) -IOEX(ID_1_USB_C1_OC_ODL, EXPIN(IOEX_ID_1_C2_NCT38XX, 0, 6), GPIO_ODR_HIGH) -IOEX(ID_1_USB_C2_OC_ODL, EXPIN(IOEX_ID_1_C2_NCT38XX, 0, 7), GPIO_ODR_HIGH) - -/* Board ID 2 IO expander configuration */ -/* GPIO02_P2 to PU */ -/* GPIO03_P2 to PU */ IOEX(USB_C0_OC_ODL, EXPIN(IOEX_C0_NCT38XX, 0, 4), GPIO_ODR_HIGH) IOEX(USB_C0_FRS_EN, EXPIN(IOEX_C0_NCT38XX, 0, 6), GPIO_LOW) IOEX(USB_C0_RT_RST_ODL, EXPIN(IOEX_C0_NCT38XX, 0, 7), GPIO_ODR_LOW) -IOEX(USB_C2_RT_RST_ODL, EXPIN(IOEX_C2_NCT38XX, 0, 2), GPIO_ODR_LOW) -IOEX(USB_C1_OC_ODL, EXPIN(IOEX_C2_NCT38XX, 0, 3), GPIO_ODR_HIGH) -IOEX(USB_C2_OC_ODL, EXPIN(IOEX_C2_NCT38XX, 0, 4), GPIO_ODR_HIGH) -IOEX(USB_C2_FRS_EN, EXPIN(IOEX_C2_NCT38XX, 0, 6), GPIO_LOW) -/* GPIO07_P2 to PU */ +GPIO(USB_C1_OC_ODL, PIN(E, 1), GPIO_ODR_HIGH) |