diff options
Diffstat (limited to 'board/kano')
-rw-r--r-- | board/kano/battery.c | 98 | ||||
-rw-r--r-- | board/kano/board.c | 101 | ||||
-rw-r--r-- | board/kano/board.h | 249 | ||||
-rw-r--r-- | board/kano/build.mk | 26 | ||||
-rw-r--r-- | board/kano/charger.c | 90 | ||||
-rw-r--r-- | board/kano/ec.tasklist | 29 | ||||
-rw-r--r-- | board/kano/fans.c | 88 | ||||
-rw-r--r-- | board/kano/fw_config.c | 60 | ||||
-rw-r--r-- | board/kano/fw_config.h | 54 | ||||
-rw-r--r-- | board/kano/generated-gpio.inc | 115 | ||||
-rw-r--r-- | board/kano/gpio.inc | 35 | ||||
-rw-r--r-- | board/kano/i2c.c | 78 | ||||
-rw-r--r-- | board/kano/keyboard.c | 25 | ||||
-rw-r--r-- | board/kano/led.c | 83 | ||||
-rw-r--r-- | board/kano/pwm.c | 57 | ||||
-rw-r--r-- | board/kano/sensors.c | 221 | ||||
-rw-r--r-- | board/kano/tune_mp2964.c | 43 | ||||
-rw-r--r-- | board/kano/usbc_config.c | 291 | ||||
-rw-r--r-- | board/kano/usbc_config.h | 21 | ||||
-rw-r--r-- | board/kano/vif_override.xml | 3 |
20 files changed, 0 insertions, 1767 deletions
diff --git a/board/kano/battery.c b/board/kano/battery.c deleted file mode 100644 index a18ab029b6..0000000000 --- a/board/kano/battery.c +++ /dev/null @@ -1,98 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - * - * Battery pack vendor provided charging profile - */ - -#include "battery_fuel_gauge.h" -#include "common.h" -#include "compile_time_macros.h" - -/* - * Battery info for all Brya battery types. Note that the fields - * start_charging_min/max and charging_min/max are not used for the charger. - * The effective temperature limits are given by discharging_min/max_c. - * - * Fuel Gauge (FG) parameters which are used for determining if the battery - * is connected, the appropriate ship mode (battery cutoff) command, and the - * charge/discharge FETs status. - * - * Ship mode (battery cutoff) requires 2 writes to the appropriate smart battery - * register. For some batteries, the charge/discharge FET bits are set when - * charging/discharging is active, in other types, these bits set mean that - * charging/discharging is disabled. Therefore, in addition to the mask for - * these bits, a disconnect value must be specified. Note that for TI fuel - * gauge, the charge/discharge FET status is found in Operation Status (0x54), - * but a read of Manufacturer Access (0x00) will return the lower 16 bits of - * Operation status which contains the FET status bits. - * - * The assumption for battery types supported is that the charge/discharge FET - * status can be read with a sb_read() command and therefore, only the register - * address, mask, and disconnect value need to be provided. - */ -const struct board_batt_params board_battery_info[] = { - /* POW-TECH GQA05 Battery Information */ - [BATTERY_POWER_TECH] = { - /* BQ40Z50 Fuel Gauge */ - .fuel_gauge = { - .manuf_name = "POW-TECH", - .device_name = "BATGQA05L22", - .ship_mode = { - .reg_addr = 0x00, - .reg_data = { 0x0010, 0x0010 }, - }, - .fet = { - .mfgacc_support = 1, - .reg_addr = 0x00, - .reg_mask = 0x2000, /* XDSG */ - .disconnect_val = 0x2000, - } - }, - .batt_info = { - .voltage_max = TARGET_WITH_MARGIN(13050, 5), - .voltage_normal = 11400, /* mV */ - .voltage_min = 9000, /* mV */ - .precharge_current = 280, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 45, - .charging_min_c = 0, - .charging_max_c = 45, - .discharging_min_c = -10, - .discharging_max_c = 60, - }, - }, - /* LGC L17L3PB0 Battery Information */ - /* - * Battery info provided by ODM on b/143477210, comment #11 - */ - [BATTERY_LGC011] = { - .fuel_gauge = { - .manuf_name = "LGC", - .ship_mode = { - .reg_addr = 0x00, - .reg_data = { 0x0010, 0x0010 }, - }, - .fet = { - .reg_addr = 0x0, - .reg_mask = 0x6000, - .disconnect_val = 0x6000, - } - }, - .batt_info = { - .voltage_max = TARGET_WITH_MARGIN(13200, 5), - .voltage_normal = 11550, /* mV */ - .voltage_min = 9000, /* mV */ - .precharge_current = 256, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 45, - .charging_min_c = 0, - .charging_max_c = 60, - .discharging_min_c = 0, - .discharging_max_c = 75, - }, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(board_battery_info) == BATTERY_TYPE_COUNT); - -const enum battery_type DEFAULT_BATTERY_TYPE = BATTERY_POWER_TECH; diff --git a/board/kano/board.c b/board/kano/board.c deleted file mode 100644 index 07dfc2cd5a..0000000000 --- a/board/kano/board.c +++ /dev/null @@ -1,101 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "battery.h" -#include "button.h" -#include "charge_ramp.h" -#include "charger.h" -#include "common.h" -#include "compile_time_macros.h" -#include "console.h" -#include "gpio.h" -#include "gpio_signal.h" -#include "hooks.h" -#include "fw_config.h" -#include "hooks.h" -#include "lid_switch.h" -#include "power_button.h" -#include "power.h" -#include "registers.h" -#include "switch.h" -#include "tablet_mode.h" -#include "throttle_ap.h" -#include "usbc_config.h" - -#include "gpio_list.h" /* Must come after other header files. */ - -/* Console output macros */ -#define CPRINTF(format, args...) cprintf(CC_CHARGER, format, ## args) -#define CPRINTS(format, args...) cprints(CC_CHARGER, format, ## args) - -/******************************************************************************/ -/* USB-A charging control */ - -const int usb_port_enable[USB_PORT_COUNT] = { - GPIO_EN_PP5000_USBA_R, -}; -BUILD_ASSERT(ARRAY_SIZE(usb_port_enable) == USB_PORT_COUNT); - -/* Called on AP S3 -> S0 transition */ -static void board_chipset_resume(void) -{ - /* Allow keyboard backlight to be enabled */ - - gpio_set_level(GPIO_EC_KB_BL_EN_L, 0); -} -DECLARE_HOOK(HOOK_CHIPSET_RESUME, board_chipset_resume, HOOK_PRIO_DEFAULT); - -/* Called on AP S0 -> S3 transition */ -static void board_chipset_suspend(void) -{ - /* Turn off the keyboard backlight if it's on. */ - - gpio_set_level(GPIO_EC_KB_BL_EN_L, 1); -} -DECLARE_HOOK(HOOK_CHIPSET_SUSPEND, board_chipset_suspend, HOOK_PRIO_DEFAULT); - -#ifdef CONFIG_CHARGE_RAMP_SW - -/* - * TODO(b/181508008): tune this threshold - */ - -#define BC12_MIN_VOLTAGE 4400 - -/** - * Return true if VBUS is too low - */ -int board_is_vbus_too_low(int port, enum chg_ramp_vbus_state ramp_state) -{ - int voltage; - - if (charger_get_vbus_voltage(port, &voltage)) - voltage = 0; - - if (voltage == 0) { - CPRINTS("%s: must be disconnected", __func__); - return 1; - } - - if (voltage < BC12_MIN_VOLTAGE) { - CPRINTS("%s: port %d: vbus %d lower than %d", __func__, - port, voltage, BC12_MIN_VOLTAGE); - return 1; - } - - return 0; -} - -#endif /* CONFIG_CHARGE_RAMP_SW */ - -enum battery_present battery_hw_present(void) -{ - enum gpio_signal batt_pres; - - batt_pres = GPIO_EC_BATT_PRES_ODL; - - /* The GPIO is low when the battery is physically present */ - return gpio_get_level(batt_pres) ? BP_NO : BP_YES; -} diff --git a/board/kano/board.h b/board/kano/board.h deleted file mode 100644 index 3372c5f3d2..0000000000 --- a/board/kano/board.h +++ /dev/null @@ -1,249 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Brya board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -#include "compile_time_macros.h" - -/* - * Early brya boards are not set up for vivaldi - */ -#undef CONFIG_KEYBOARD_VIVALDI - -/* Baseboard features */ -#include "baseboard.h" - -/* - * This will happen automatically on NPCX9 ES2 and later. Do not remove - * until we can confirm all earlier chips are out of service. - */ -#define CONFIG_HIBERNATE_PSL_VCC1_RST_WAKEUP - -#define CONFIG_MP2964 - -/* LED */ -#define CONFIG_LED_PWM -#define CONFIG_LED_PWM_COUNT 1 -#undef CONFIG_LED_PWM_NEAR_FULL_COLOR -#undef CONFIG_LED_PWM_SOC_ON_COLOR -#undef CONFIG_LED_PWM_SOC_SUSPEND_COLOR -#undef CONFIG_LED_PWM_LOW_BATT_COLOR -#define CONFIG_LED_PWM_NEAR_FULL_COLOR EC_LED_COLOR_WHITE -#define CONFIG_LED_PWM_SOC_ON_COLOR EC_LED_COLOR_WHITE -#define CONFIG_LED_PWM_SOC_SUSPEND_COLOR EC_LED_COLOR_WHITE -#define CONFIG_LED_PWM_LOW_BATT_COLOR EC_LED_COLOR_AMBER - -/* Sensors */ -#define CONFIG_ACCELGYRO_ICM426XX /* Base accel */ -#define CONFIG_ACCELGYRO_ICM_COMM_I2C -#define CONFIG_ACCELGYRO_ICM426XX_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) - -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* FIFO size is in power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -/* Depends on how fast the AP boots and typical ODRs */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) - -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL) - -/* Lid accel */ -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_UPDATE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL -#define CONFIG_ACCEL_KX022 - -#define CONFIG_ACCEL_INTERRUPTS - -/* Sensor console commands */ -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO - -/* USB Type A Features */ -#define USB_PORT_COUNT 1 -#define CONFIG_USB_PORT_POWER_DUMB - -/* USB Type C and USB PD defines */ -#define CONFIG_USB_PD_REQUIRE_AP_MODE_ENTRY - -#define CONFIG_USBC_RETIMER_INTEL_BB - -#define CONFIG_USBC_PPC_SYV682X - -#undef CONFIG_USB_PD_TCPM_NCT38XX -#define CONFIG_USB_PD_TCPM_RT1715 - -/* TODO: b/177608416 - measure and check these values on brya */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ -#define PD_VCONN_SWAP_DELAY 5000 /* us */ - -/* - * Passive USB-C cables only support up to 60W. - */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 60000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 - -/* - * Macros for GPIO signals used in common code that don't match the - * schematic names. Signal names in gpio.inc match the schematic and are - * then redefined here to so it's more clear which signal is being used for - * which purpose. - */ -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL -#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL -#define GPIO_ENABLE_BACKLIGHT GPIO_EC_EN_EDP_BL -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV -#define GPIO_PACKET_MODE_EN GPIO_EC_GSC_PACKET_MODE -#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL -#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L -#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST -#define GPIO_PCH_SLP_S0_L GPIO_SYS_SLP_S0IX_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L - -/* - * GPIO_EC_PCH_INT_ODL is used for MKBP events as well as a PCH wakeup - * signal. - */ -#define GPIO_PCH_WAKE_L GPIO_EC_PCH_INT_ODL -#define GPIO_PG_EC_ALL_SYS_PWRGD GPIO_SEQ_EC_ALL_SYS_PG -#define GPIO_PG_EC_DSW_PWROK GPIO_SEQ_EC_DSW_PWROK -#define GPIO_PG_EC_RSMRST_ODL GPIO_SEQ_EC_RSMRST_ODL -#define GPIO_POWER_BUTTON_L GPIO_GSC_EC_PWR_BTN_ODL -#define GPIO_RSMRST_L_PGOOD GPIO_SEQ_EC_RSMRST_ODL -#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL -#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL -#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL -#define GPIO_WP_L GPIO_EC_WP_ODL - -/* System has back-lit keyboard */ -#define CONFIG_PWM_KBLIGHT - -/* I2C Bus Configuration */ - -#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 - -#define I2C_PORT_USB_C0_C2_TCPC NPCX_I2C_PORT1_0 -#define I2C_PORT_USB_C1_TCPC NPCX_I2C_PORT4_1 - -#define I2C_PORT_USB_C0_C2_PPC NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_C1_PPC NPCX_I2C_PORT6_1 - -#define I2C_PORT_USB_C0_C2_BC12 NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_C1_BC12 NPCX_I2C_PORT6_1 - -#define I2C_PORT_USB_C0_C2_MUX NPCX_I2C_PORT3_0 -#define I2C_PORT_USB_C1_MUX NPCX_I2C_PORT6_1 - -#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0 -#define I2C_PORT_CHARGER NPCX_I2C_PORT7_0 -#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 -#define I2C_PORT_MP2964 NPCX_I2C_PORT7_0 - -#define I2C_ADDR_EEPROM_FLAGS 0x50 - -#define I2C_ADDR_MP2964_FLAGS 0x20 - -/* - * see b/174768555#comment22 - */ -#define USBC_PORT_C0_BB_RETIMER_I2C_ADDR 0x54 -/* SOC facing Burnside Bridge retimer */ -#define USBC_PORT_C1_SOC_BB_RETIMER_I2C_ADDR 0x55 -/* Type-C connector facing Burnside Bridge retimer */ -#define USBC_PORT_C1_BB_RETIMER_I2C_ADDR 0x56 - -/* Enabling Thunderbolt-compatible mode */ -#define CONFIG_USB_PD_TBT_COMPAT_MODE - -/* Enabling USB4 mode */ -#define CONFIG_USB_PD_USB4 - -/* Retimer */ -#define CONFIG_USBC_RETIMER_FW_UPDATE - -/* Thermal features */ -#define CONFIG_THERMISTOR -#define CONFIG_TEMP_SENSOR -#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_SEQ_EC_DSW_PWROK -#define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B - -/* - * TODO(b/181271666): no fan control loop until sensors are tuned - */ -/* #define CONFIG_FANS FAN_CH_COUNT */ - -/* Charger defines */ -#define CONFIG_CHARGER_ISL9241 -#define CONFIG_CHARGE_RAMP_SW -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" /* needed by registers.h */ -#include "registers.h" -#include "usbc_config.h" - -enum adc_channel { - ADC_TEMP_SENSOR_1_DDR_SOC, - ADC_TEMP_SENSOR_2_FAN, - ADC_TEMP_SENSOR_3_CHARGER, - ADC_CH_COUNT -}; - -enum temp_sensor_id { - TEMP_SENSOR_1_DDR_SOC, - TEMP_SENSOR_2_FAN, - TEMP_SENSOR_COUNT -}; - -enum sensor_id { - LID_ACCEL = 0, - BASE_ACCEL, - BASE_GYRO, - SENSOR_COUNT -}; - -enum battery_type { - BATTERY_POWER_TECH, - BATTERY_LGC011, - BATTERY_TYPE_COUNT -}; - -enum pwm_channel { - PWM_CH_LED2 = 0, /* PWM0 (white charger) */ - PWM_CH_LED1, /* PWM2 (orange charger) */ - PWM_CH_KBLIGHT, /* PWM3 */ - PWM_CH_FAN, /* PWM5 */ - PWM_CH_COUNT -}; - -enum fan_channel { - FAN_CH_0 = 0, - FAN_CH_COUNT -}; - -enum mft_channel { - MFT_CH_0 = 0, - MFT_CH_COUNT -}; - -void motion_interrupt(enum gpio_signal signal); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ diff --git a/board/kano/build.mk b/board/kano/build.mk deleted file mode 100644 index 6d1303a15a..0000000000 --- a/board/kano/build.mk +++ /dev/null @@ -1,26 +0,0 @@ -# -*- makefile -*- -# Copyright 2021 The Chromium OS Authors. All rights reserved. -# Use of this source code is governed by a BSD-style license that can be -# found in the LICENSE file. -# -# Brya board specific files build -# - -CHIP:=npcx -CHIP_FAMILY:=npcx9 -CHIP_VARIANT:=npcx9m3f -BASEBOARD:=brya - -board-y= -board-y+=battery.o -board-y+=board.o -board-y+=charger.o -board-y+=fans.o -board-y+=fw_config.o -board-y+=i2c.o -board-y+=keyboard.o -board-y+=led.o -board-y+=pwm.o -board-y+=sensors.o -board-y+=tune_mp2964.o -board-y+=usbc_config.o diff --git a/board/kano/charger.c b/board/kano/charger.c deleted file mode 100644 index 9f7c760858..0000000000 --- a/board/kano/charger.c +++ /dev/null @@ -1,90 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "common.h" - -#include "charge_manager.h" -#include "charge_state_v2.h" -#include "charger.h" -#include "compile_time_macros.h" -#include "console.h" -#include "driver/charger/isl9241.h" -#include "usbc_ppc.h" -#include "usb_pd.h" -#include "util.h" - - -#define CPRINTSUSB(format, args...) cprints(CC_USBCHARGE, format, ## args) -#define CPRINTFUSB(format, args...) cprintf(CC_USBCHARGE, format, ## args) - -/* Charger Chip Configuration */ -const struct charger_config_t chg_chips[] = { - { - .i2c_port = I2C_PORT_CHARGER, - .i2c_addr_flags = ISL9241_ADDR_FLAGS, - .drv = &isl9241_drv, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(chg_chips) == CHARGER_NUM); - -int board_set_active_charge_port(int port) -{ - int is_valid_port = board_is_usb_pd_port_present(port); - int i; - - if (port == CHARGE_PORT_NONE) { - CPRINTSUSB("Disabling all charger ports"); - - /* Disable all ports. */ - for (i = 0; i < ppc_cnt; i++) { - /* - * Do not return early if one fails otherwise we can - * get into a boot loop assertion failure. - */ - if (ppc_vbus_sink_enable(i, 0)) - CPRINTSUSB("Disabling C%d as sink failed.", i); - } - - return EC_SUCCESS; - } else if (!is_valid_port) { - return EC_ERROR_INVAL; - } - - /* Check if the port is sourcing VBUS. */ - if (ppc_is_sourcing_vbus(port)) { - CPRINTFUSB("Skip enable C%d", port); - return EC_ERROR_INVAL; - } - - CPRINTSUSB("New charge port: C%d", port); - - /* - * Turn off the other ports' sink path FETs, before enabling the - * requested charge port. - */ - for (i = 0; i < ppc_cnt; i++) { - if (i == port) - continue; - - if (ppc_vbus_sink_enable(i, 0)) - CPRINTSUSB("C%d: sink path disable failed.", i); - } - - /* Enable requested charge port. */ - if (ppc_vbus_sink_enable(port, 1)) { - CPRINTSUSB("C%d: sink path enable failed.", port); - return EC_ERROR_UNKNOWN; - } - - return EC_SUCCESS; -} - -__overridable void board_set_charge_limit(int port, int supplier, int charge_ma, - int max_ma, int charge_mv) -{ - charge_set_input_current_limit(MAX(charge_ma, - CONFIG_CHARGER_INPUT_CURRENT), - charge_mv); -} diff --git a/board/kano/ec.tasklist b/board/kano/ec.tasklist deleted file mode 100644 index 7574c1839d..0000000000 --- a/board/kano/ec.tasklist +++ /dev/null @@ -1,29 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* - * See CONFIG_TASK_LIST in config.h for details. - * - * USB_CHG_Px tasks must be contiguous (see USB_CHG_PORT_TO_TASK_ID(x)). - * PD_Cx tasks must be contiguous (see PD_PORT_TO_TASK_ID(x)) - */ - -#define CONFIG_TASK_LIST \ - TASK_ALWAYS(HOOKS, hook_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(CHG_RAMP, chg_ramp_task, NULL, TASK_STACK_SIZE) \ - TASK_ALWAYS(USB_CHG_P0, usb_charger_task, 0, TASK_STACK_SIZE) \ - TASK_ALWAYS(USB_CHG_P1, usb_charger_task, 0, TASK_STACK_SIZE) \ - TASK_ALWAYS(CHARGER, charger_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_NOTEST(KEYPROTO, keyboard_protocol_task, NULL, TASK_STACK_SIZE) \ - TASK_NOTEST(CHIPSET, chipset_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(HOSTCMD, host_command_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(CONSOLE, console_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(POWERBTN, power_button_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_NOTEST(KEYSCAN, keyboard_scan_task, NULL, TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_C0, pd_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_C1, pd_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_INT_C0, pd_shared_alert_task, (BIT(2) | BIT(0)), TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_INT_C1, pd_interrupt_handler_task, 1, TASK_STACK_SIZE) diff --git a/board/kano/fans.c b/board/kano/fans.c deleted file mode 100644 index d966056331..0000000000 --- a/board/kano/fans.c +++ /dev/null @@ -1,88 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Physical fans. These are logically separate from pwm_channels. */ - -#include "common.h" -#include "compile_time_macros.h" -#include "console.h" -#include "fan_chip.h" -#include "fan.h" -#include "hooks.h" -#include "pwm.h" - -/* MFT channels. These are logically separate from pwm_channels. */ -const struct mft_t mft_channels[] = { - [MFT_CH_0] = { - .module = NPCX_MFT_MODULE_1, - .clk_src = TCKC_LFCLK, - .pwm_id = PWM_CH_FAN, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(mft_channels) == MFT_CH_COUNT); - -static const struct fan_conf fan_conf_0 = { - .flags = FAN_USE_RPM_MODE, - .ch = MFT_CH_0, /* Use MFT id to control fan */ - .pgood_gpio = -1, - .enable_gpio = GPIO_EN_PP5000_FAN, -}; - -/* - * TOOD(b/180681346): need to update for real fan - * - * Prototype fan spins at about 7200 RPM at 100% PWM. - * Set minimum at around 30% PWM. - */ -static const struct fan_rpm fan_rpm_0 = { - .rpm_min = 2200, - .rpm_start = 2200, - .rpm_max = 7200, -}; - -const struct fan_t fans[FAN_CH_COUNT] = { - [FAN_CH_0] = { - .conf = &fan_conf_0, - .rpm = &fan_rpm_0, - }, -}; - -#ifndef CONFIG_FANS - -/* - * TODO(b/181271666): use static fan speeds until fan and sensors are - * tuned. for now, use: - * - * AP off: 33% - * AP on: 100% - */ - -static void fan_slow(void) -{ - const int duty_pct = 33; - - ccprints("%s: speed %d%%", __func__, duty_pct); - - pwm_enable(PWM_CH_FAN, 1); - pwm_set_duty(PWM_CH_FAN, duty_pct); -} - -static void fan_max(void) -{ - const int duty_pct = 100; - - ccprints("%s: speed %d%%", __func__, duty_pct); - - pwm_enable(PWM_CH_FAN, 1); - pwm_set_duty(PWM_CH_FAN, duty_pct); -} - -DECLARE_HOOK(HOOK_INIT, fan_slow, HOOK_PRIO_DEFAULT); -DECLARE_HOOK(HOOK_CHIPSET_SUSPEND, fan_slow, HOOK_PRIO_DEFAULT); -DECLARE_HOOK(HOOK_CHIPSET_SHUTDOWN, fan_slow, HOOK_PRIO_DEFAULT); -DECLARE_HOOK(HOOK_CHIPSET_RESET, fan_max, HOOK_PRIO_FIRST); -DECLARE_HOOK(HOOK_CHIPSET_RESUME, fan_max, HOOK_PRIO_DEFAULT); - -#endif /* CONFIG_FANS */ diff --git a/board/kano/fw_config.c b/board/kano/fw_config.c deleted file mode 100644 index fb8acb635d..0000000000 --- a/board/kano/fw_config.c +++ /dev/null @@ -1,60 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "common.h" -#include "compile_time_macros.h" -#include "console.h" -#include "cros_board_info.h" -#include "fw_config.h" - -#define CPRINTS(format, args...) cprints(CC_CHIPSET, format, ## args) - -static union brya_cbi_fw_config fw_config; -BUILD_ASSERT(sizeof(fw_config) == sizeof(uint32_t)); - -/* - * FW_CONFIG defaults for brya if the CBI.FW_CONFIG data is not - * initialized. - */ -static const union brya_cbi_fw_config fw_config_defaults = { - .usb_db = DB_USB3_PS8815, - .kb_bl = KEYBOARD_BACKLIGHT_ENABLED, -}; - -/**************************************************************************** - * Brya FW_CONFIG access - */ -void board_init_fw_config(void) -{ - if (cbi_get_fw_config(&fw_config.raw_value)) { - CPRINTS("CBI: Read FW_CONFIG failed, using board defaults"); - fw_config = fw_config_defaults; - } - - if (get_board_id() == 0) { - /* - * Early boards have a zero'd out FW_CONFIG, so replace - * it with a sensible default value. If DB_USB_ABSENT2 - * was used as an alternate encoding of DB_USB_ABSENT to - * avoid the zero check, then fix it. - */ - if (fw_config.raw_value == 0) { - CPRINTS("CBI: FW_CONFIG is zero, using board defaults"); - fw_config = fw_config_defaults; - } else if (fw_config.usb_db == DB_USB_ABSENT2) { - fw_config.usb_db = DB_USB_ABSENT; - } - } -} - -union brya_cbi_fw_config get_fw_config(void) -{ - return fw_config; -} - -enum ec_cfg_usb_db_type ec_cfg_usb_db_type(void) -{ - return fw_config.usb_db; -} diff --git a/board/kano/fw_config.h b/board/kano/fw_config.h deleted file mode 100644 index 6e4eb3ef58..0000000000 --- a/board/kano/fw_config.h +++ /dev/null @@ -1,54 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#ifndef __BOARD_BRYA_FW_CONFIG_H_ -#define __BOARD_BRYA_FW_CONFIG_H_ - -#include <stdint.h> - -/**************************************************************************** - * CBI FW_CONFIG layout for Brya board. - * - * Source of truth is the project/brya/brya/config.star configuration file. - */ - -enum ec_cfg_usb_db_type { - DB_USB_ABSENT = 0, - DB_USB3_PS8815 = 1, - DB_USB_ABSENT2 = 15 -}; - -enum ec_cfg_keyboard_backlight_type { - KEYBOARD_BACKLIGHT_DISABLED = 0, - KEYBOARD_BACKLIGHT_ENABLED = 1 -}; - -union brya_cbi_fw_config { - struct { - enum ec_cfg_usb_db_type usb_db : 4; - uint32_t sd_db : 2; - uint32_t lte_db : 1; - enum ec_cfg_keyboard_backlight_type kb_bl : 1; - uint32_t audio : 3; - uint32_t reserved_1 : 21; - }; - uint32_t raw_value; -}; - -/** - * Read the cached FW_CONFIG. Guaranteed to have valid values. - * - * @return the FW_CONFIG for the board. - */ -union brya_cbi_fw_config get_fw_config(void); - -/** - * Get the USB daughter board type from FW_CONFIG. - * - * @return the USB daughter board type. - */ -enum ec_cfg_usb_db_type ec_cfg_usb_db_type(void); - -#endif /* __BOARD_BRYA_FW_CONFIG_H_ */ diff --git a/board/kano/generated-gpio.inc b/board/kano/generated-gpio.inc deleted file mode 100644 index d65d64feca..0000000000 --- a/board/kano/generated-gpio.inc +++ /dev/null @@ -1,115 +0,0 @@ -/* - * This file was auto-generated. - */ - -/* INTERRUPT GPIOs: */ -GPIO_INT(ACOK_OD, PIN(0, 0), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, extpower_interrupt) -GPIO_INT(EC_IMU_INT_R_L, PIN(5, 6), GPIO_SEL_1P8V | GPIO_INT_FALLING, motion_interrupt) -GPIO_INT(EC_PROCHOT_IN_L, PIN(F, 0), GPIO_INT_BOTH, throttle_ap_prochot_input_interrupt) -GPIO_INT(EC_VOLDN_BTN_ODL, PIN(9, 3), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(EC_VOLUP_BTN_ODL, PIN(9, 7), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(EC_WP_ODL, PIN(A, 1), GPIO_INT_BOTH, switch_interrupt) -GPIO_INT(GSC_EC_PWR_BTN_ODL, PIN(0, 1), GPIO_INT_BOTH | GPIO_HIB_WAKE_LOW, power_button_interrupt) -GPIO_INT(LID_OPEN, PIN(D, 2), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, lid_interrupt) -GPIO_INT(SEQ_EC_ALL_SYS_PG, PIN(F, 4), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(SEQ_EC_DSW_PWROK, PIN(C, 7), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(SEQ_EC_RSMRST_ODL, PIN(E, 2), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(SLP_S3_L, PIN(A, 5), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(SLP_SUS_L, PIN(F, 1), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(SYS_SLP_S0IX_L, PIN(D, 5), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(TABLET_MODE_L, PIN(9, 5), GPIO_INT_BOTH, gmr_tablet_switch_isr) -GPIO_INT(USB_C0_BC12_INT_ODL, PIN(C, 6), GPIO_INT_FALLING, bc12_interrupt) -GPIO_INT(USB_C0_C2_TCPC_INT_ODL, PIN(E, 0), GPIO_INT_FALLING, tcpc_alert_event) -GPIO_INT(USB_C0_PPC_INT_ODL, PIN(6, 2), GPIO_INT_FALLING, ppc_interrupt) -GPIO_INT(USB_C0_RT_INT_ODL, PIN(B, 1), GPIO_INT_FALLING, retimer_interrupt) -GPIO_INT(USB_C1_BC12_INT_ODL, PIN(5, 0), GPIO_INT_FALLING, bc12_interrupt) -GPIO_INT(USB_C1_PPC_INT_ODL, PIN(F, 5), GPIO_INT_FALLING, ppc_interrupt) -GPIO_INT(USB_C1_TCPC_INT_ODL, PIN(A, 2), GPIO_INT_FALLING, tcpc_alert_event) - -/* USED GPIOs: */ -GPIO(CCD_MODE_ODL, PIN(E, 5), GPIO_INPUT) -GPIO(CHARGER_VAP_OTG_EN, PIN(7, 3), GPIO_OUT_LOW) -GPIO(CPU_C10_GATE_L, PIN(6, 7), GPIO_INPUT) -GPIO(EC_BATT_PRES_ODL, PIN(A, 3), GPIO_INPUT) -GPIO(EC_ENTERING_RW, PIN(0, 3), GPIO_OUT_LOW) -GPIO(EC_EN_EDP_BL, PIN(D, 3), GPIO_OUT_HIGH) -GPIO(EC_GSC_PACKET_MODE, PIN(7, 5), GPIO_OUT_LOW) -GPIO(EC_I2C_BAT_SCL, PIN(3, 3), GPIO_INPUT) -GPIO(EC_I2C_BAT_SDA, PIN(3, 6), GPIO_INPUT) -GPIO(EC_I2C_MISC_SCL_R, PIN(B, 3), GPIO_INPUT) -GPIO(EC_I2C_MISC_SDA_R, PIN(B, 2), GPIO_INPUT) -GPIO(EC_I2C_SENSOR_SCL, PIN(B, 5), GPIO_INPUT | GPIO_SEL_1P8V) -GPIO(EC_I2C_SENSOR_SDA, PIN(B, 4), GPIO_INPUT | GPIO_SEL_1P8V) -GPIO(EC_I2C_USB_C0_C2_PPC_BC_SCL, PIN(9, 2), GPIO_INPUT) -GPIO(EC_I2C_USB_C0_C2_PPC_BC_SDA, PIN(9, 1), GPIO_INPUT) -GPIO(EC_I2C_USB_C0_C2_RT_SCL, PIN(D, 1), GPIO_INPUT) -GPIO(EC_I2C_USB_C0_C2_RT_SDA, PIN(D, 0), GPIO_INPUT) -GPIO(EC_I2C_USB_C0_C2_TCPC_SCL, PIN(9, 0), GPIO_INPUT) -GPIO(EC_I2C_USB_C0_C2_TCPC_SDA, PIN(8, 7), GPIO_INPUT) -GPIO(EC_I2C_USB_C1_MIX_SCL, PIN(E, 4), GPIO_INPUT) -GPIO(EC_I2C_USB_C1_MIX_SDA, PIN(E, 3), GPIO_INPUT) -GPIO(EC_I2C_USB_C1_TCPC_SCL, PIN(F, 3), GPIO_INPUT) -GPIO(EC_I2C_USB_C1_TCPC_SDA, PIN(F, 2), GPIO_INPUT) -GPIO(EC_KB_BL_EN_L, PIN(8, 6), GPIO_OUT_HIGH) -GPIO(EC_PCHHOT_ODL, PIN(7, 4), GPIO_INPUT) -GPIO(EC_PCH_INT_ODL, PIN(B, 0), GPIO_ODR_HIGH) -GPIO(EC_PCH_PWR_BTN_ODL, PIN(C, 1), GPIO_ODR_HIGH) -GPIO(EC_PCH_RSMRST_L, PIN(A, 6), GPIO_OUT_LOW) -GPIO(EC_PCH_RTCRST, PIN(7, 6), GPIO_OUT_LOW) -GPIO(EC_PCH_SYS_PWROK, PIN(3, 7), GPIO_OUT_LOW) -GPIO(EC_PCH_WAKE_R_ODL, PIN(C, 0), GPIO_ODR_HIGH) -GPIO(EC_PROCHOT_ODL, PIN(6, 3), GPIO_ODR_HIGH) -GPIO(EN_PP5000_FAN, PIN(6, 1), GPIO_OUT_HIGH) -GPIO(EN_PP5000_USBA_R, PIN(D, 7), GPIO_OUT_LOW) -GPIO(EN_S5_RAILS, PIN(B, 6), GPIO_OUT_LOW) -GPIO(IMVP9_VRRDY_OD, PIN(4, 3), GPIO_INPUT) -GPIO(PCH_PWROK, PIN(7, 2), GPIO_OUT_LOW) -GPIO(SYS_RST_ODL, PIN(C, 5), GPIO_ODR_HIGH) -GPIO(USB_C1_FRS_EN, PIN(9, 4), GPIO_OUT_LOW) -GPIO(USB_C1_RT_INT_ODL, PIN(A, 0), GPIO_INPUT) -GPIO(USB_C1_RT_RST_R_ODL, PIN(0, 2), GPIO_ODR_LOW) -GPIO(VCCST_PWRGD_OD, PIN(A, 4), GPIO_ODR_LOW) - -/* UART alternate functions */ -ALTERNATE(PIN_MASK(6, 0x30), 0, MODULE_UART, 0) /* GPIO64/CR_SIN1, GPO65/CR_SOUT1/FLPRG1_L */ - -/* I2C alternate functions */ -ALTERNATE(PIN_MASK(3, 0x48), 0, MODULE_I2C, 0) /* GPIO33/I2C5_SCL0/CTS_L, GPIO36/RTS_L/I2C5_SDA0 */ -ALTERNATE(PIN_MASK(8, 0x80), 0, MODULE_I2C, 0) /* GPIO87/I2C1_SDA0 */ -ALTERNATE(PIN_MASK(9, 0x07), 0, MODULE_I2C, 0) /* GPIO92/I2C2_SCL0, GPIO91/I2C2_SDA0, GPIO90/I2C1_SCL0 */ -ALTERNATE(PIN_MASK(B, 0x0c), 0, MODULE_I2C, 0) /* GPIOB3/I2C7_SCL0/DCD_L, GPIOB2/I2C7_SDA0/DSR_L */ -ALTERNATE(PIN_MASK(B, 0x30), 0, MODULE_I2C, GPIO_SEL_1P8V) /* GPIOB5/I2C0_SCL0, GPIOB4/I2C0_SDA0 */ -ALTERNATE(PIN_MASK(D, 0x03), 0, MODULE_I2C, 0) /* GPIOD1/I2C3_SCL0, GPIOD0/I2C3_SDA0 */ -ALTERNATE(PIN_MASK(E, 0x18), 0, MODULE_I2C, 0) /* GPIOE4/I2C6_SCL1/I3C_SCL, GPIOE3/I2C6_SDA1/I3C_SDA */ -ALTERNATE(PIN_MASK(F, 0x0c), 0, MODULE_I2C, 0) /* GPIOF3/I2C4_SCL1, GPIOF2/I2C4_SDA1 */ - -/* PWM alternate functions */ -ALTERNATE(PIN_MASK(4, 0x01), 0, MODULE_PWM, 0) /* GPIO40/TA1 */ -ALTERNATE(PIN_MASK(8, 0x01), 0, MODULE_PWM, 0) /* GPIO80/PWM3 */ -ALTERNATE(PIN_MASK(B, 0x80), 0, MODULE_PWM, 0) /* GPIOB7/PWM5 */ -ALTERNATE(PIN_MASK(C, 0x18), 0, MODULE_PWM, 0) /* GPIOC4/PWM2, GPIOC3/PWM0 */ - -/* ADC alternate functions */ -ALTERNATE(PIN_MASK(3, 0x10), 0, MODULE_ADC, 0) /* GPIO34/PS2_DAT2/ADC6 */ -ALTERNATE(PIN_MASK(4, 0x34), 0, MODULE_ADC, 0) /* GPIO42/ADC3/RI_L, GPIO45/ADC0, GPIO44/ADC1 */ - -/* KB alternate functions */ -ALTERNATE(PIN_MASK(0, 0xf0), 0, MODULE_KB, GPIO_ODR_HIGH) /* KSO10&P80_CLK/GPIO07, KSO11&P80_DAT/GPIO06, KSO12/GPIO05, KSO13/GPIO04 */ -ALTERNATE(PIN_MASK(1, 0x7f), 0, MODULE_KB, GPIO_ODR_HIGH) /* KSO06/GPO13/GP_SEL_L, KSO07/GPO12/JEN_L, KSO03/GPIO16/JTAG_TDO0_SWO, KSO04/GPIO15/XNOR, KSO05/GPIO14, KSO08/GPIO11/CR_SOUT1, KSO09/GPIO10/CR_SIN1 */ -ALTERNATE(PIN_MASK(2, 0xfc), 0, MODULE_KB, GPIO_INPUT | GPIO_PULL_UP) /* KSI2/GPIO27/TRACEDATA1, KSI3/GPIO26/TRACEDATA0, KSI4/GPIO25/TRACECLK/GP_SCLK, KSI5/GPIO24/GP_MISO, KSI6/GPIO23/S_SBUB, KSI7/GPIO22/S_SBUA */ -ALTERNATE(PIN_MASK(2, 0x03), 0, MODULE_KB, GPIO_ODR_HIGH) /* KSO00/GPIO21/JTAG_TCK_SWCLK, KSO01/GPIO20/JTAG_TMS_SWIO */ -ALTERNATE(PIN_MASK(3, 0x03), 0, MODULE_KB, GPIO_INPUT | GPIO_PULL_UP) /* KSI0/GPIO31/TRACEDATA3/GP_MOSI, KSI1/GPIO30/TRACEDATA2/GP_CS_L */ -ALTERNATE(PIN_MASK(8, 0x04), 0, MODULE_KB, GPIO_ODR_HIGH) /* KSO14/GPIO82 */ - -/* PMU alternate functions */ -ALTERNATE(PIN_MASK(0, 0x01), 0, MODULE_PMU, GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH) /* PSL_IN2_L&GPI00/GPIO00 */ -ALTERNATE(PIN_MASK(0, 0x02), 0, MODULE_PMU, GPIO_INT_BOTH | GPIO_HIB_WAKE_LOW) /* GPIO01/PSL_IN3_L&GPI01 */ -ALTERNATE(PIN_MASK(D, 0x04), 0, MODULE_PMU, GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH) /* PSL_IN1_L&GPID2/GPIOD2 */ - -/* Unused Pins */ -UNUSED(PIN(D, 6)) /* GPOD6/CR_SOUT3/SHDF_ESPI_L */ -UNUSED(PIN(3, 2)) /* GPO32/TRIS_L */ -UNUSED(PIN(3, 5)) /* GPO35/CR_SOUT4/TEST_L */ -UNUSED(PIN(6, 6)) /* GPIO66 */ - -/* Pre-configured PSL balls: J8 K6 */ diff --git a/board/kano/gpio.inc b/board/kano/gpio.inc deleted file mode 100644 index 465f0fd4db..0000000000 --- a/board/kano/gpio.inc +++ /dev/null @@ -1,35 +0,0 @@ -/* -*- mode:c -*- - * - * Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#define MODULE_KB MODULE_KEYBOARD_SCAN - -/* - * Generated-gpio.inc is produced using a Brya specific tool that - * parses the GPIO definitions derived from the board schematics and - * EC pinout descriptions derived form the chip datasheets to generate - * the Chrome EC GPIO pinout definitions. Due to the confidential - * nature of schematics and datasheets, they are not provided here. - * - * Variants that do not auto-generate their GPIO definitions should - * combine the Brya gpio.inc and generated-gpio.inc into their - * gpio.inc and customize as appropriate. - */ - -#include "generated-gpio.inc" - -/* - * The NPCX keyboard driver does not use named GPIOs to access - * keyboard scan pins, so we do not list them in *gpio.inc. However, when - * KEYBOARD_COL2_INVERTED is defined, this name is required. - */ -GPIO(EC_KSO_02_INV, PIN(1, 7), GPIO_OUT_LOW) - -GPIO(USB_C0_OC_ODL, PIN(D, 4), GPIO_ODR_HIGH) -GPIO(USB_C0_FRS_EN, PIN(6, 0), GPIO_LOW) -GPIO(USB_C0_RT_RST_ODL, PIN(C, 2), GPIO_ODR_LOW) - -GPIO(USB_C1_OC_ODL, PIN(E, 1), GPIO_ODR_HIGH) diff --git a/board/kano/i2c.c b/board/kano/i2c.c deleted file mode 100644 index bb55b13d0c..0000000000 --- a/board/kano/i2c.c +++ /dev/null @@ -1,78 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "common.h" -#include "compile_time_macros.h" - -#include "i2c.h" - -/* I2C port map configuration */ -const struct i2c_port_t i2c_ports[] = { - { - /* I2C0 */ - .name = "sensor", - .port = I2C_PORT_SENSOR, - .kbps = 400, - .scl = GPIO_EC_I2C_SENSOR_SCL, - .sda = GPIO_EC_I2C_SENSOR_SDA, - }, - { - /* I2C1 */ - .name = "tcpc0,2", - .port = I2C_PORT_USB_C0_C2_TCPC, - .kbps = 1000, - .scl = GPIO_EC_I2C_USB_C0_C2_TCPC_SCL, - .sda = GPIO_EC_I2C_USB_C0_C2_TCPC_SDA, - }, - { - /* I2C2 */ - .name = "ppc0,2", - .port = I2C_PORT_USB_C0_C2_PPC, - .kbps = 1000, - .scl = GPIO_EC_I2C_USB_C0_C2_PPC_BC_SCL, - .sda = GPIO_EC_I2C_USB_C0_C2_PPC_BC_SDA, - }, - { - /* I2C3 */ - .name = "retimer0,2", - .port = I2C_PORT_USB_C0_C2_MUX, - .kbps = 1000, - .scl = GPIO_EC_I2C_USB_C0_C2_RT_SCL, - .sda = GPIO_EC_I2C_USB_C0_C2_RT_SDA, - }, - { - /* I2C4 C1 TCPC */ - .name = "tcpc1", - .port = I2C_PORT_USB_C1_TCPC, - .kbps = 400, - .scl = GPIO_EC_I2C_USB_C1_TCPC_SCL, - .sda = GPIO_EC_I2C_USB_C1_TCPC_SDA, - }, - { - /* I2C5 */ - .name = "battery", - .port = I2C_PORT_BATTERY, - .kbps = 100, - .scl = GPIO_EC_I2C_BAT_SCL, - .sda = GPIO_EC_I2C_BAT_SDA, - }, - { - /* I2C6 */ - .name = "ppc1", - .port = I2C_PORT_USB_C1_PPC, - .kbps = 400, - .scl = GPIO_EC_I2C_USB_C1_MIX_SCL, - .sda = GPIO_EC_I2C_USB_C1_MIX_SDA, - }, - { - /* I2C7 */ - .name = "eeprom", - .port = I2C_PORT_EEPROM, - .kbps = 400, - .scl = GPIO_EC_I2C_MISC_SCL_R, - .sda = GPIO_EC_I2C_MISC_SDA_R, - }, -}; -const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports); diff --git a/board/kano/keyboard.c b/board/kano/keyboard.c deleted file mode 100644 index a9f033130d..0000000000 --- a/board/kano/keyboard.c +++ /dev/null @@ -1,25 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "common.h" - -#include "keyboard_scan.h" -#include "timer.h" - -/* Keyboard scan setting */ -__override struct keyboard_scan_config keyscan_config = { - /* Increase from 50 us, because KSO_02 passes through the H1. */ - .output_settle_us = 80, - /* Other values should be the same as the default configuration. */ - .debounce_down_us = 9 * MSEC, - .debounce_up_us = 30 * MSEC, - .scan_period_us = 3 * MSEC, - .min_post_scan_delay_us = 1000, - .poll_timeout_us = 100 * MSEC, - .actual_key_mask = { - 0x14, 0xff, 0xff, 0xff, 0xff, 0xf5, 0xff, - 0xa4, 0xff, 0xfe, 0x55, 0xfa, 0xca /* full set */ - }, -}; diff --git a/board/kano/led.c b/board/kano/led.c deleted file mode 100644 index ab1021b845..0000000000 --- a/board/kano/led.c +++ /dev/null @@ -1,83 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Brya specific PWM LED settings: there are 2 LEDs on each side of the board, - * each one can be controlled separately. The LED colors are white or amber, - * and the default behavior is tied to the charging process: both sides are - * amber while charging the battery and white when the battery is charged. - */ - -#include <stdint.h> - -#include "common.h" -#include "compile_time_macros.h" -#include "ec_commands.h" -#include "led_pwm.h" -#include "pwm.h" -#include "util.h" - -const enum ec_led_id supported_led_ids[] = { - EC_LED_ID_LEFT_LED, - EC_LED_ID_RIGHT_LED, -}; - -const int supported_led_ids_count = ARRAY_SIZE(supported_led_ids); - -/* - * We only have a white and an amber LED, so setting any other color results in - * both LEDs being off. - */ -struct pwm_led_color_map led_color_map[EC_LED_COLOR_COUNT] = { - /* Amber, White */ - [EC_LED_COLOR_RED] = { 0, 0 }, - [EC_LED_COLOR_GREEN] = { 0, 0 }, - [EC_LED_COLOR_BLUE] = { 0, 0 }, - [EC_LED_COLOR_YELLOW] = { 0, 0 }, - [EC_LED_COLOR_WHITE] = { 0, 100 }, - [EC_LED_COLOR_AMBER] = { 100, 0 }, -}; - -/* Two logical LEDs with amber and white channels. */ -struct pwm_led pwm_leds[CONFIG_LED_PWM_COUNT] = { - { - .ch0 = PWM_CH_LED1, - .ch1 = PWM_CH_LED2, - .ch2 = PWM_LED_NO_CHANNEL, - .enable = &pwm_enable, - .set_duty = &pwm_set_duty, - }, -}; - -void led_get_brightness_range(enum ec_led_id led_id, uint8_t *brightness_range) -{ - memset(brightness_range, '\0', - sizeof(*brightness_range) * EC_LED_COLOR_COUNT); - brightness_range[EC_LED_COLOR_AMBER] = 100; - brightness_range[EC_LED_COLOR_WHITE] = 100; -} - -int led_set_brightness(enum ec_led_id led_id, const uint8_t *brightness) -{ - enum pwm_led_id pwm_id; - - /* Convert ec_led_id to pwm_led_id. */ - switch (led_id) { - case EC_LED_ID_LEFT_LED: - pwm_id = PWM_LED0; - break; - default: - return EC_ERROR_UNKNOWN; - } - - if (brightness[EC_LED_COLOR_WHITE]) - set_pwm_led_color(pwm_id, EC_LED_COLOR_WHITE); - else if (brightness[EC_LED_COLOR_AMBER]) - set_pwm_led_color(pwm_id, EC_LED_COLOR_AMBER); - else - /* Otherwise, the "color" is "off". */ - set_pwm_led_color(pwm_id, -1); - - return EC_SUCCESS; -} diff --git a/board/kano/pwm.c b/board/kano/pwm.c deleted file mode 100644 index 66239d606f..0000000000 --- a/board/kano/pwm.c +++ /dev/null @@ -1,57 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "common.h" - -#include "compile_time_macros.h" -#include "hooks.h" -#include "pwm.h" -#include "pwm_chip.h" - -const struct pwm_t pwm_channels[] = { - [PWM_CH_LED2] = { - .channel = 0, - .flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, - .freq = 4800, - }, - [PWM_CH_LED1] = { - .channel = 2, - .flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, - .freq = 4800, - }, - [PWM_CH_KBLIGHT] = { - .channel = 3, - .flags = 0, - /* - * Set PWM frequency to multiple of 50 Hz and 60 Hz to prevent - * flicker. Higher frequencies consume similar average power to - * lower PWM frequencies, but higher frequencies record a much - * lower maximum power. - */ - .freq = 2400, - }, - [PWM_CH_FAN] = { - .channel = 5, - .flags = PWM_CONFIG_OPEN_DRAIN, - .freq = 25000 - }, -}; -BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT); - -static void board_pwm_init(void) -{ - /* - * Turn on all the LED at 50%. - * Turn on the fan at 100%. - */ - pwm_enable(PWM_CH_LED1, 1); - pwm_set_duty(PWM_CH_LED1, 50); - pwm_enable(PWM_CH_LED2, 1); - pwm_set_duty(PWM_CH_LED2, 50); - - pwm_enable(PWM_CH_KBLIGHT, 1); - pwm_set_duty(PWM_CH_KBLIGHT, 50); -} -DECLARE_HOOK(HOOK_INIT, board_pwm_init, HOOK_PRIO_DEFAULT); diff --git a/board/kano/sensors.c b/board/kano/sensors.c deleted file mode 100644 index 0859e9082c..0000000000 --- a/board/kano/sensors.c +++ /dev/null @@ -1,221 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "common.h" -#include "accelgyro.h" -#include "adc_chip.h" -#include "driver/accelgyro_icm426xx.h" -#include "driver/accelgyro_icm_common.h" -#include "driver/accel_kionix.h" -#include "hooks.h" -#include "motion_sense.h" -#include "temp_sensor.h" -#include "thermal.h" -#include "temp_sensor/thermistor.h" - -/* ADC configuration */ -const struct adc_t adc_channels[] = { - [ADC_TEMP_SENSOR_1_DDR_SOC] = { - .name = "TEMP_DDR_SOC", - .input_ch = NPCX_ADC_CH0, - .factor_mul = ADC_MAX_VOLT, - .factor_div = ADC_READ_MAX + 1, - .shift = 0, - }, - [ADC_TEMP_SENSOR_2_FAN] = { - .name = "TEMP_FAN", - .input_ch = NPCX_ADC_CH1, - .factor_mul = ADC_MAX_VOLT, - .factor_div = ADC_READ_MAX + 1, - .shift = 0, - }, - [ADC_TEMP_SENSOR_3_CHARGER] = { - .name = "TEMP_CHARGER", - .input_ch = NPCX_ADC_CH6, - .factor_mul = ADC_MAX_VOLT, - .factor_div = ADC_READ_MAX + 1, - .shift = 0, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT); - -K_MUTEX_DEFINE(g_lid_accel_mutex); -K_MUTEX_DEFINE(g_base_accel_mutex); -static struct kionix_accel_data g_kx022_data; -static struct icm_drv_data_t g_icm426xx_data; - -/* - * TODO:(b/197200940): Verify lid and base orientation - * matrix on proto board. - */ -static const mat33_fp_t lid_standard_ref = { - { FLOAT_TO_FP(-1), 0, 0}, - { 0, FLOAT_TO_FP(-1), 0}, - { 0, 0, FLOAT_TO_FP(-1)} -}; -static const mat33_fp_t base_standard_ref = { - { FLOAT_TO_FP(1), 0, 0}, - { 0, FLOAT_TO_FP(1), 0}, - { 0, 0, FLOAT_TO_FP(1)} -}; - -struct motion_sensor_t motion_sensors[] = { - [LID_ACCEL] = { - .name = "Lid Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_KX022, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_LID, - .drv = &kionix_accel_drv, - .mutex = &g_lid_accel_mutex, - .drv_data = &g_kx022_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = KX022_ADDR0_FLAGS, - .flags = MOTIONSENSE_FLAG_INT_SIGNAL, - .rot_standard_ref = &lid_standard_ref, /* identity matrix */ - .default_range = 2, /* g */ - .min_frequency = KX022_ACCEL_MIN_FREQ, - .max_frequency = KX022_ACCEL_MAX_FREQ, - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 12500 | ROUND_UP_FLAG, - }, - /* Sensor on for lid angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - }, - }, - - [BASE_ACCEL] = { - .name = "Base Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_ICM426XX, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_BASE, - .drv = &icm426xx_drv, - .mutex = &g_base_accel_mutex, - .drv_data = &g_icm426xx_data, - .int_signal = GPIO_EC_IMU_INT_R_L, - .flags = MOTIONSENSE_FLAG_INT_SIGNAL, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS, - .rot_standard_ref = &base_standard_ref, - .default_range = 4, /* g */ - .min_frequency = ICM426XX_ACCEL_MIN_FREQ, - .max_frequency = ICM426XX_ACCEL_MAX_FREQ, - .config = { - [SENSOR_CONFIG_EC_S0] = { - .odr = 13000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - }, - }, - - [BASE_GYRO] = { - .name = "Base Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_ICM426XX, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_BASE, - .drv = &icm426xx_drv, - .mutex = &g_base_accel_mutex, - .drv_data = &g_icm426xx_data, - .int_signal = GPIO_EC_IMU_INT_R_L, - .flags = MOTIONSENSE_FLAG_INT_SIGNAL, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS, - .default_range = 1000 | ROUND_UP_FLAG, /* dps */ - .rot_standard_ref = &base_standard_ref, - .min_frequency = ICM426XX_GYRO_MIN_FREQ, - .max_frequency = ICM426XX_GYRO_MAX_FREQ, - }, -}; -const unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors); - -static void baseboard_sensors_init(void) -{ - /* Enable gpio interrupt for base accelgyro sensor */ - gpio_enable_interrupt(GPIO_EC_IMU_INT_R_L); -} -DECLARE_HOOK(HOOK_INIT, baseboard_sensors_init, HOOK_PRIO_INIT_I2C + 1); - -void motion_interrupt(enum gpio_signal signal) -{ - icm426xx_interrupt(signal); -} - -/* Temperature sensor configuration */ -const struct temp_sensor_t temp_sensors[] = { - [TEMP_SENSOR_1_DDR_SOC] = { - .name = "DDR and SOC", - .type = TEMP_SENSOR_TYPE_BOARD, - .read = get_temp_3v3_30k9_47k_4050b, - .idx = ADC_TEMP_SENSOR_1_DDR_SOC - }, - [TEMP_SENSOR_2_FAN] = { - .name = "FAN", - .type = TEMP_SENSOR_TYPE_BOARD, - .read = get_temp_3v3_30k9_47k_4050b, - .idx = ADC_TEMP_SENSOR_2_FAN - }, -}; -BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT); - -/* - * TODO(b/180681346): update for Alder Lake/brya - * - * Tiger Lake specifies 100 C as maximum TDP temperature. THRMTRIP# occurs at - * 130 C. However, sensor is located next to DDR, so we need to use the lower - * DDR temperature limit (85 C) - */ -static const struct ec_thermal_config thermal_cpu = { - .temp_host = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(70), - [EC_TEMP_THRESH_HALT] = C_TO_K(80), - }, - .temp_host_release = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(65), - }, - .temp_fan_off = C_TO_K(35), - .temp_fan_max = C_TO_K(50), -}; - -/* - * TODO(b/180681346): update for Alder Lake/brya - * - * Inductor limits - used for both charger and PP3300 regulator - * - * Need to use the lower of the charger IC, PP3300 regulator, and the inductors - * - * Charger max recommended temperature 100C, max absolute temperature 125C - * PP3300 regulator: operating range -40 C to 145 C - * - * Inductors: limit of 125c - * PCB: limit is 80c - */ -static const struct ec_thermal_config thermal_fan = { - .temp_host = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(75), - [EC_TEMP_THRESH_HALT] = C_TO_K(80), - }, - .temp_host_release = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(65), - }, - .temp_fan_off = C_TO_K(40), - .temp_fan_max = C_TO_K(55), -}; - -/* this should really be "const" */ -struct ec_thermal_config thermal_params[] = { - [TEMP_SENSOR_1_DDR_SOC] = thermal_cpu, - [TEMP_SENSOR_2_FAN] = thermal_fan, -}; -BUILD_ASSERT(ARRAY_SIZE(thermal_params) == TEMP_SENSOR_COUNT); diff --git a/board/kano/tune_mp2964.c b/board/kano/tune_mp2964.c deleted file mode 100644 index 198f06d8eb..0000000000 --- a/board/kano/tune_mp2964.c +++ /dev/null @@ -1,43 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Tune the MP2964 IMVP9.1 parameters for brya */ - -#include "common.h" -#include "compile_time_macros.h" -#include "console.h" -#include "hooks.h" -#include "mp2964.h" - -const static struct mp2964_reg_val rail_a[] = { - { MP2964_MFR_ALT_SET, 0xe081 }, /* ALERT_DELAY = 200ns */ -}; -const static struct mp2964_reg_val rail_b[] = { - { MP2964_MFR_ALT_SET, 0xe081 }, /* ALERT_DELAY = 200ns */ -}; - -static void mp2964_on_startup(void) -{ - static int chip_updated; - int status; - - if (get_board_id() != 1) - return; - - if (chip_updated) - return; - - chip_updated = 1; - - ccprintf("%s: attempting to tune PMIC\n", __func__); - - status = mp2964_tune(rail_a, ARRAY_SIZE(rail_a), - rail_b, ARRAY_SIZE(rail_b)); - if (status != EC_SUCCESS) - ccprintf("%s: could not update all settings\n", __func__); -} - -DECLARE_HOOK(HOOK_CHIPSET_STARTUP, mp2964_on_startup, - HOOK_PRIO_FIRST); diff --git a/board/kano/usbc_config.c b/board/kano/usbc_config.c deleted file mode 100644 index 8f41a325b1..0000000000 --- a/board/kano/usbc_config.c +++ /dev/null @@ -1,291 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include <stdint.h> -#include <stdbool.h> - -#include "common.h" -#include "compile_time_macros.h" -#include "console.h" -#include "driver/bc12/pi3usb9201_public.h" -#include "driver/ppc/syv682x_public.h" -#include "driver/retimer/bb_retimer_public.h" -#include "driver/tcpm/rt1715.h" -#include "driver/tcpm/tcpci.h" -#include "ec_commands.h" -#include "fw_config.h" -#include "gpio.h" -#include "gpio_signal.h" -#include "hooks.h" -#include "ioexpander.h" -#include "system.h" -#include "task.h" -#include "task_id.h" -#include "timer.h" -#include "usbc_config.h" -#include "usbc_ppc.h" -#include "usb_charge.h" -#include "usb_mux.h" -#include "usb_pd.h" -#include "usb_pd_tcpm.h" - -#define CPRINTF(format, args...) cprintf(CC_USBPD, format, ## args) -#define CPRINTS(format, args...) cprints(CC_USBPD, format, ## args) - -/* USBC TCPC configuration */ -const struct tcpc_config_t tcpc_config[] = { - [USBC_PORT_C0] = { - .bus_type = EC_BUS_TYPE_I2C, - .i2c_info = { - .port = I2C_PORT_USB_C0_C2_TCPC, - .addr_flags = RT1715_I2C_ADDR_FLAGS, - }, - .drv = &rt1715_tcpm_drv, - .flags = TCPC_FLAGS_TCPCI_REV2_0 | - TCPC_FLAGS_TCPCI_REV2_0_NO_VSAFE0V, - }, - [USBC_PORT_C1] = { - .bus_type = EC_BUS_TYPE_I2C, - .i2c_info = { - .port = I2C_PORT_USB_C1_TCPC, - .addr_flags = RT1715_I2C_ADDR_FLAGS, - }, - .drv = &rt1715_tcpm_drv, - .flags = TCPC_FLAGS_TCPCI_REV2_0 | - TCPC_FLAGS_TCPCI_REV2_0_NO_VSAFE0V, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(tcpc_config) == USBC_PORT_COUNT); -BUILD_ASSERT(CONFIG_USB_PD_PORT_MAX_COUNT == USBC_PORT_COUNT); - -/* USBC PPC configuration */ -struct ppc_config_t ppc_chips[] = { - [USBC_PORT_C0] = { - .i2c_port = I2C_PORT_USB_C0_C2_PPC, - .i2c_addr_flags = SYV682X_ADDR0_FLAGS, - .drv = &syv682x_drv, - }, - [USBC_PORT_C1] = { - /* Compatible with Silicon Mitus SM536A0 */ - .i2c_port = I2C_PORT_USB_C1_PPC, - .i2c_addr_flags = SYV682X_ADDR0_FLAGS, - .drv = &syv682x_drv, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(ppc_chips) == USBC_PORT_COUNT); - -unsigned int ppc_cnt = ARRAY_SIZE(ppc_chips); - -/* USBC mux configuration - Alder Lake includes internal mux */ -static const struct usb_mux usbc0_tcss_usb_mux = { - .usb_port = USBC_PORT_C0, - .driver = &virtual_usb_mux_driver, - .hpd_update = &virtual_hpd_update, -}; - -static const struct usb_mux usbc1_tcss_usb_mux = { - .usb_port = USBC_PORT_C1, - .driver = &virtual_usb_mux_driver, - .hpd_update = &virtual_hpd_update, -}; - -struct usb_mux soc_side_bb_retimer_usb_mux = { - .usb_port = USBC_PORT_C1, - .driver = &bb_usb_retimer, - .hpd_update = bb_retimer_hpd_update, - .i2c_port = I2C_PORT_USB_C1_MUX, - .i2c_addr_flags = USBC_PORT_C1_SOC_BB_RETIMER_I2C_ADDR, - .next_mux = &usbc1_tcss_usb_mux, -}; - -const struct usb_mux usb_muxes[] = { - [USBC_PORT_C0] = { - .usb_port = USBC_PORT_C0, - .driver = &bb_usb_retimer, - .hpd_update = bb_retimer_hpd_update, - .i2c_port = I2C_PORT_USB_C0_C2_MUX, - .i2c_addr_flags = USBC_PORT_C0_BB_RETIMER_I2C_ADDR, - .next_mux = &usbc0_tcss_usb_mux, - }, - [USBC_PORT_C1] = { - .usb_port = USBC_PORT_C1, - .driver = &bb_usb_retimer, - .hpd_update = bb_retimer_hpd_update, - .i2c_port = I2C_PORT_USB_C1_MUX, - .i2c_addr_flags = USBC_PORT_C1_BB_RETIMER_I2C_ADDR, - .next_mux = &soc_side_bb_retimer_usb_mux, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(usb_muxes) == USBC_PORT_COUNT); - -/* BC1.2 charger detect configuration */ -const struct pi3usb9201_config_t pi3usb9201_bc12_chips[] = { - [USBC_PORT_C0] = { - .i2c_port = I2C_PORT_USB_C0_C2_BC12, - .i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS, - }, - [USBC_PORT_C1] = { - .i2c_port = I2C_PORT_USB_C1_BC12, - .i2c_addr_flags = PI3USB9201_I2C_ADDR_2_FLAGS, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(pi3usb9201_bc12_chips) == USBC_PORT_COUNT); - -__override int bb_retimer_power_enable(const struct usb_mux *me, bool enable) -{ - enum gpio_signal rst_signal; - - if (me->usb_port == USBC_PORT_C0) { - rst_signal = GPIO_USB_C0_RT_RST_ODL; - } else if (me->usb_port == USBC_PORT_C1) { - rst_signal = GPIO_USB_C1_RT_RST_R_ODL; - } else { - return EC_ERROR_INVAL; - } - - /* - * We do not have a load switch for the burnside bridge chips, - * so we only need to sequence reset. - */ - - if (enable) { - /* - * Tpw, minimum time from VCC to RESET_N de-assertion is 100us. - * For boards that don't provide a load switch control, the - * retimer_init() function ensures power is up before calling - * this function. - */ - gpio_set_level(rst_signal, 1); - /* - * Allow 1ms time for the retimer to power up lc_domain - * which powers I2C controller within retimer - */ - msleep(1); - } else { - gpio_set_level(rst_signal, 0); - msleep(1); - } - return EC_SUCCESS; -} - -void board_reset_pd_mcu(void) -{ - /* - * TODO(b/179648104): figure out correct timing - */ - - gpio_set_level(GPIO_USB_C0_RT_RST_ODL, 0); - gpio_set_level(GPIO_USB_C1_RT_RST_R_ODL, 0); - - /* - * delay for power-on to reset-off and min. assertion time - */ - - msleep(20); - - gpio_set_level(GPIO_USB_C0_RT_RST_ODL, 1); - gpio_set_level(GPIO_USB_C1_RT_RST_R_ODL, 1); - - /* wait for chips to come up */ - - msleep(50); -} - -static void board_tcpc_init(void) -{ - /* Don't reset TCPCs after initial reset */ - if (!system_jumped_late()) - board_reset_pd_mcu(); - - /* Enable PPC interrupts. */ - gpio_enable_interrupt(GPIO_USB_C0_PPC_INT_ODL); - - /* Enable TCPC interrupts. */ - gpio_enable_interrupt(GPIO_USB_C0_C2_TCPC_INT_ODL); - - /* Enable BC1.2 interrupts. */ - gpio_enable_interrupt(GPIO_USB_C0_BC12_INT_ODL); - - gpio_enable_interrupt(GPIO_USB_C1_PPC_INT_ODL); - gpio_enable_interrupt(GPIO_USB_C1_TCPC_INT_ODL); - gpio_enable_interrupt(GPIO_USB_C1_BC12_INT_ODL); -} -DECLARE_HOOK(HOOK_INIT, board_tcpc_init, HOOK_PRIO_INIT_CHIPSET); - -uint16_t tcpc_get_alert_status(void) -{ - uint16_t status = 0; - - if (gpio_get_level(GPIO_USB_C0_C2_TCPC_INT_ODL) == 0) - status |= PD_STATUS_TCPC_ALERT_0 | PD_STATUS_TCPC_ALERT_2; - - if (gpio_get_level(GPIO_USB_C1_TCPC_INT_ODL) == 0) - status |= PD_STATUS_TCPC_ALERT_1; - - return status; -} - -int ppc_get_alert_status(int port) -{ - if (port == USBC_PORT_C0) - return gpio_get_level(GPIO_USB_C0_PPC_INT_ODL) == 0; - else if (port == USBC_PORT_C1) - return gpio_get_level(GPIO_USB_C1_PPC_INT_ODL) == 0; - return 0; -} - -void tcpc_alert_event(enum gpio_signal signal) -{ - switch (signal) { - case GPIO_USB_C0_C2_TCPC_INT_ODL: - schedule_deferred_pd_interrupt(USBC_PORT_C0); - break; - case GPIO_USB_C1_TCPC_INT_ODL: - schedule_deferred_pd_interrupt(USBC_PORT_C1); - break; - default: - break; - } -} - -void bc12_interrupt(enum gpio_signal signal) -{ - switch (signal) { - case GPIO_USB_C0_BC12_INT_ODL: - task_set_event(TASK_ID_USB_CHG_P0, USB_CHG_EVENT_BC12); - break; - case GPIO_USB_C1_BC12_INT_ODL: - task_set_event(TASK_ID_USB_CHG_P1, USB_CHG_EVENT_BC12); - break; - default: - break; - } -} - -void ppc_interrupt(enum gpio_signal signal) -{ - switch (signal) { - case GPIO_USB_C0_PPC_INT_ODL: - syv682x_interrupt(USBC_PORT_C0); - break; - case GPIO_USB_C1_PPC_INT_ODL: - syv682x_interrupt(USBC_PORT_C1); - break; - default: - break; - } -} - -void retimer_interrupt(enum gpio_signal signal) -{ - /* - * TODO(b/179513527): add USB-C support - */ -} - -__override bool board_is_dts_port(int port) -{ - return port == USBC_PORT_C0; -} diff --git a/board/kano/usbc_config.h b/board/kano/usbc_config.h deleted file mode 100644 index 87e601ee3e..0000000000 --- a/board/kano/usbc_config.h +++ /dev/null @@ -1,21 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Brya board-specific USB-C configuration */ - -#ifndef __CROS_EC_USBC_CONFIG_H -#define __CROS_EC_USBC_CONFIG_H - -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 - -enum usbc_port { - USBC_PORT_C0 = 0, - USBC_PORT_C1, - USBC_PORT_COUNT -}; - -void config_usb_db_type(void); - -#endif /* __CROS_EC_USBC_CONFIG_H */ diff --git a/board/kano/vif_override.xml b/board/kano/vif_override.xml deleted file mode 100644 index 32736caf64..0000000000 --- a/board/kano/vif_override.xml +++ /dev/null @@ -1,3 +0,0 @@ -<!-- Add VIF field overrides here. See genvif.c and the Vendor Info File - Definition from the USB-IF. ---> |