diff options
Diffstat (limited to 'board/kukui/gpio.inc')
| -rw-r--r-- | board/kukui/gpio.inc | 29 |
1 files changed, 7 insertions, 22 deletions
diff --git a/board/kukui/gpio.inc b/board/kukui/gpio.inc index 4986e878a2..04010dc714 100644 --- a/board/kukui/gpio.inc +++ b/board/kukui/gpio.inc @@ -45,19 +45,8 @@ GPIO_INT(GAUGE_INT_ODL, PIN(C, 9), GPIO_INT_FALLING | GPIO_PULL_UP, gauge_interrupt) /* Interrupts not implemented yet */ -#if BOARD_REV < 2 -GPIO(ALS_INT_ODL, PIN(A, 6), GPIO_INPUT) -#elif BOARD_REV >= 2 /* TODO(b:122993147): It's also an analog input. */ GPIO(POGO_ADC_INT_L, PIN(A, 6), GPIO_INPUT) -#endif - -/* Voltage rails control pins */ -#if BOARD_REV < 2 -GPIO(PP3300_S0_EN, PIN(B, 6), GPIO_OUT_LOW) -GPIO(PP1800_S3_EN, PIN(C, 7), GPIO_OUT_LOW) -GPIO(PP3300_S3_EN, PIN(D, 2), GPIO_OUT_LOW) -#endif /* Reset pins */ GPIO(AP_SYS_RST_L, PIN(C, 11), GPIO_OUT_LOW) @@ -78,18 +67,13 @@ GPIO(I2C2_SDA, PIN(A, 12), GPIO_INPUT) /* Analog pins */ GPIO(BATT_ID, PIN(A, 7), GPIO_ANALOG) GPIO(BOARD_ID, PIN(C, 0), GPIO_ANALOG) -#if BOARD_REV >= 2 GPIO(EC_SKU_ID, PIN(B, 0), GPIO_ANALOG) -GPIO(USBC_THERM, PIN(C, 4), GPIO_ANALOG) -#endif /* Other input pins */ GPIO(WP_L, PIN(C, 8), GPIO_INPUT) /* EC_FLASH_WP_ODL */ GPIO(BOOT0, PIN(F, 11), GPIO_INPUT) GPIO(CCD_MODE_ODL, PIN(A, 1), GPIO_INPUT) -#if BOARD_REV >= 2 GPIO(POGO_VBUS_PRESENT, PIN(A, 14), GPIO_INPUT) -#endif /* Other output pins */ GPIO(ENTERING_RW, PIN(C, 6), GPIO_ODR_HIGH) /* EC_ENTERING_RW_ODL */ @@ -99,17 +83,18 @@ GPIO(USB_C0_DP_POLARITY, PIN(C, 14), GPIO_OUT_LOW) GPIO(USB_C0_HPD_OD, PIN(F, 1), GPIO_ODR_LOW) GPIO(BOOTBLOCK_EN_L, PIN(C, 1), GPIO_ODR_HIGH) GPIO(USB_C0_DP_OE_L, PIN(A, 5), GPIO_OUT_HIGH) -#if BOARD_REV < 2 -GPIO(USB_C0_DISCHARGE, PIN(B, 0), GPIO_OUT_LOW) -GPIO(BOOTBLOCK_MUX_OE, PIN(C, 4), GPIO_ODR_HIGH) -GPIO(USB_ID, PIN(A, 13), GPIO_ODR_HIGH) -#elif BOARD_REV >= 2 GPIO(EN_PP3300_POGO, PIN(A, 13), GPIO_OUT_LOW) GPIO(EN_POGO_CHARGE_L, PIN(B, 6), GPIO_OUT_HIGH) GPIO(EN_USBC_CHARGE_L, PIN(C, 7), GPIO_OUT_LOW) GPIO(EN_PP5000_USBC, PIN(D, 2), GPIO_OUT_LOW) -#endif +/* + * It's a P1 pin BOOTBLOCK_MUX_OE, also a P2 pin USBC_THERM (test poin). + * Keep this pin defaults to P1 setting since that eMMC enabled with + * High-Z stat. + * TODO(b:122866184): Rename this pin as BC12_DET_EN. + */ +GPIO(USBC_THERM, PIN(C, 4), GPIO_ODR_HIGH) /* USART1: PA9/PA10 */ ALTERNATE(PIN_MASK(A, 0x0600), 1, MODULE_UART, 0) |