diff options
Diffstat (limited to 'board/lindar/board.h')
-rw-r--r-- | board/lindar/board.h | 101 |
1 files changed, 47 insertions, 54 deletions
diff --git a/board/lindar/board.h b/board/lindar/board.h index bc49b8514d..7c407d05a7 100644 --- a/board/lindar/board.h +++ b/board/lindar/board.h @@ -1,4 +1,4 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. +/* Copyright 2020 The ChromiumOS Authors * Use of this source code is governed by a BSD-style license that can be * found in the LICENSE file. */ @@ -27,12 +27,11 @@ /* Sensors */ #define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT -#define CONFIG_ACCEL_LIS2DE /* Lid accel */ -#define CONFIG_ACCELGYRO_LSM6DSM /* Base accel */ +#define CONFIG_ACCEL_LIS2DE /* Lid accel */ +#define CONFIG_ACCELGYRO_LSM6DSM /* Base accel */ /* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK \ - BIT(LID_ACCEL) +#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL) #define CONFIG_LID_ANGLE #define CONFIG_LID_ANGLE_UPDATE @@ -43,31 +42,29 @@ TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) /* USB Type C and USB PD defines */ -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 - -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ +#define CONFIG_USB_PD_PORT_MAX_COUNT 2 +#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ +#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ /* * SN5S30 PPC supports up to 24V VBUS source and sink, however passive USB-C * cables only support up to 60W. */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 45000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 - +#define PD_OPERATING_POWER_MW 15000 +#define PD_MAX_POWER_MW 45000 +#define PD_MAX_CURRENT_MA 3000 +#define PD_MAX_VOLTAGE_MV 20000 #undef CONFIG_USB_MUX_RUNTIME_CONFIG /* USB Type A Features */ -#define USB_PORT_COUNT 1 +#define USB_PORT_COUNT 1 #define CONFIG_USB_PORT_POWER_DUMB /* USBC PPC*/ -#define CONFIG_USBC_PPC_SN5S330 /* USBC port C0 */ -#define CONFIG_USBC_PPC_SYV682X /* USBC port C1 */ +#define CONFIG_USBC_PPC_SN5S330 /* USBC port C0 */ +#define CONFIG_USBC_PPC_SYV682X /* USBC port C1 */ /* BC 1.2 */ @@ -76,8 +73,8 @@ /* Fan features */ /* charger defines */ -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 +#define CONFIG_CHARGER_SENSE_RESISTOR 10 +#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 /* Retimer */ #undef CONFIG_USBC_RETIMER_INTEL_BB @@ -92,42 +89,42 @@ * then redefined here to so it's more clear which signal is being used for * which purpose. */ -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL -#define GPIO_EN_PP5000 GPIO_EN_PP5000_A -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_LID_OPEN GPIO_EC_LID_OPEN -#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV -#define GPIO_PACKET_MODE_EN GPIO_EC_H1_PACKET_MODE -#define GPIO_PCH_WAKE_L GPIO_EC_PCH_WAKE_ODL -#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL -#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_ODL -#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST -#define GPIO_PCH_SYS_PWROK GPIO_EC_PCH_SYS_PWROK -#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GPIO_POWER_BUTTON_L GPIO_H1_EC_PWR_BTN_ODL -#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL -#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL -#define GPIO_WP_L GPIO_EC_WP_L -#define GPIO_USB_C1_BC12_INT_ODL GPIO_USB_C1_MIX_INT_ODL -#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL -#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_MUTE_BTN_ODL +#define GPIO_AC_PRESENT GPIO_ACOK_OD +#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL +#define GPIO_EN_PP5000 GPIO_EN_PP5000_A +#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW +#define GPIO_LID_OPEN GPIO_EC_LID_OPEN +#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV +#define GPIO_PACKET_MODE_EN GPIO_EC_H1_PACKET_MODE +#define GPIO_PCH_WAKE_L GPIO_EC_PCH_WAKE_ODL +#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL +#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_ODL +#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST +#define GPIO_PCH_SYS_PWROK GPIO_EC_PCH_SYS_PWROK +#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L +#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L +#define GPIO_POWER_BUTTON_L GPIO_H1_EC_PWR_BTN_ODL +#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL +#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL +#define GPIO_WP_L GPIO_EC_WP_L +#define GPIO_USB_C1_BC12_INT_ODL GPIO_USB_C1_MIX_INT_ODL +#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL +#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_MUTE_BTN_ODL /* I2C Bus Configuration */ #define CONFIG_I2C #define CONFIG_I2C_BUS_MAY_BE_UNPOWERED -#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 -#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0 -#define I2C_PORT_USB_C1 NPCX_I2C_PORT2_0 -#define I2C_PORT_LIGHTBAR NPCX_I2C_PORT3_0 -#define I2C_PORT_POWER NPCX_I2C_PORT5_0 -#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 +#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 +#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0 +#define I2C_PORT_USB_C1 NPCX_I2C_PORT2_0 +#define I2C_PORT_LIGHTBAR NPCX_I2C_PORT3_0 +#define I2C_PORT_POWER NPCX_I2C_PORT5_0 +#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 -#define I2C_PORT_BATTERY I2C_PORT_POWER -#define I2C_PORT_CHARGER I2C_PORT_EEPROM +#define I2C_PORT_BATTERY I2C_PORT_POWER +#define I2C_PORT_CHARGER I2C_PORT_EEPROM -#define I2C_ADDR_EEPROM_FLAGS 0x50 +#define I2C_ADDR_EEPROM_FLAGS 0x50 #define CONFIG_I2C_CONTROLLER #ifndef __ASSEMBLER__ @@ -156,11 +153,7 @@ enum sensor_id { SENSOR_COUNT, }; -enum usbc_port { - USBC_PORT_C0 = 0, - USBC_PORT_C1, - USBC_PORT_COUNT -}; +enum usbc_port { USBC_PORT_C0 = 0, USBC_PORT_C1, USBC_PORT_COUNT }; void board_reset_pd_mcu(void); |