diff options
Diffstat (limited to 'board/lingcod/board.c')
-rw-r--r-- | board/lingcod/board.c | 542 |
1 files changed, 0 insertions, 542 deletions
diff --git a/board/lingcod/board.c b/board/lingcod/board.c deleted file mode 100644 index c294100b02..0000000000 --- a/board/lingcod/board.c +++ /dev/null @@ -1,542 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Malefor board-specific configuration */ -#include "button.h" -#include "cbi_ec_fw_config.h" -#include "common.h" -#include "driver/accel_lis2dh.h" -#include "driver/accelgyro_lsm6dsm.h" -#include "driver/bc12/pi3usb9201.h" -#include "driver/ppc/sn5s330.h" -#include "driver/ppc/syv682x.h" -#include "driver/tcpm/tcpci.h" -#include "driver/tcpm/tusb422.h" -#include "driver/retimer/bb_retimer_public.h" -#include "driver/sync.h" -#include "extpower.h" -#include "fan.h" -#include "fan_chip.h" -#include "gpio.h" -#include "hooks.h" -#include "keyboard_scan.h" -#include "lid_switch.h" -#include "power.h" -#include "power_button.h" -#include "pwm.h" -#include "pwm_chip.h" -#include "switch.h" -#include "system.h" -#include "task.h" -#include "tablet_mode.h" -#include "uart.h" -#include "usb_mux.h" -#include "usb_pd.h" -#include "usb_pd_tcpm.h" -#include "usbc_ppc.h" -#include "util.h" - -#include "gpio_list.h" /* Must come after other header files. */ - -#define CPRINTS(format, args...) cprints(CC_CHIPSET, format, ## args) -#define CPRINTF(format, args...) cprintf(CC_CHIPSET, format, ## args) - -/* Keyboard scan setting */ -__override struct keyboard_scan_config keyscan_config = { - /* Increase from 50 us, because KSO_02 passes through the H1. */ - .output_settle_us = 80, - /* Other values should be the same as the default configuration. */ - .debounce_down_us = 9 * MSEC, - .debounce_up_us = 30 * MSEC, - .scan_period_us = 3 * MSEC, - .min_post_scan_delay_us = 1000, - .poll_timeout_us = 100 * MSEC, - .actual_key_mask = { - 0x14, 0xff, 0xff, 0xff, 0xff, 0xf5, 0xff, - 0xa4, 0xff, 0xfe, 0x55, 0xfa, 0xca /* full set */ - }, -}; - -/******************************************************************************/ -/* - * FW_CONFIG defaults for Malefor if the CBI data is not initialized. - */ -union volteer_cbi_fw_config fw_config_defaults = { - .usb_db = DB_USB3_NO_A, -}; - -static void board_init(void) -{ - if (ec_cfg_has_tabletmode()) { - /* Enable gpio interrupt for base accelgyro sensor */ - gpio_enable_interrupt(GPIO_EC_IMU_INT_L); - } else { - motion_sensor_count = 0; - /* Device is clamshell only */ - tablet_set_mode(0, TABLET_TRIGGER_LID); - /* Gyro is not present, don't allow line to float */ - gpio_set_flags(GPIO_EC_IMU_INT_L, GPIO_INPUT | GPIO_PULL_DOWN); - } - - /* - * TODO: b/154447182 - Malefor will control power LED and battery LED - * independently, and keep the max brightness of power LED and battery - * LED as 50%. - */ - pwm_enable(PWM_CH_LED4_SIDESEL, 1); - pwm_set_duty(PWM_CH_LED4_SIDESEL, 50); -} -DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT); - -int board_is_lid_angle_tablet_mode(void) -{ - return ec_cfg_has_tabletmode(); -} - -/* Enable or disable input devices, based on tablet mode or chipset state */ -__override void lid_angle_peripheral_enable(int enable) -{ - if (ec_cfg_has_tabletmode()) { - if (chipset_in_state(CHIPSET_STATE_ANY_OFF) || - tablet_get_mode()) - enable = 0; - keyboard_scan_enable(enable, KB_SCAN_DISABLE_LID_ANGLE); - } -} - -/******************************************************************************/ -/* Sensors */ -/* Lid and base Sensor mutex */ -static struct mutex g_lid_accel_mutex; -static struct mutex g_base_mutex; - -/* Lid and base accel private data */ -static struct stprivate_data g_lis2dh_data; -static struct lsm6dsm_data lsm6dsm_data = LSM6DSM_DATA; - -/* Matrix to rotate lid and base sensor into standard reference frame */ -static const mat33_fp_t lid_standard_ref = { - { 0, FLOAT_TO_FP(1), 0}, - { FLOAT_TO_FP(1), 0, 0}, - { 0, 0, FLOAT_TO_FP(-1)} -}; - -static const mat33_fp_t base_standard_ref = { - { FLOAT_TO_FP(1), 0, 0}, - { 0, FLOAT_TO_FP(-1), 0}, - { 0, 0, FLOAT_TO_FP(-1)} -}; - -struct motion_sensor_t motion_sensors[] = { - [LID_ACCEL] = { - .name = "Lid Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_LIS2DE, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_LID, - .drv = &lis2dh_drv, - .mutex = &g_lid_accel_mutex, - .drv_data = &g_lis2dh_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = LIS2DH_ADDR1_FLAGS, - .rot_standard_ref = &lid_standard_ref, - .min_frequency = LIS2DH_ODR_MIN_VAL, - .max_frequency = LIS2DH_ODR_MAX_VAL, - .default_range = 2, /* g, to support tablet mode */ - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - /* Sensor on in S3 */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - }, - }, - - [BASE_ACCEL] = { - .name = "Base Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_LSM6DSM, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_BASE, - .drv = &lsm6dsm_drv, - .mutex = &g_base_mutex, - .drv_data = LSM6DSM_ST_DATA(lsm6dsm_data, - MOTIONSENSE_TYPE_ACCEL), - .int_signal = GPIO_EC_IMU_INT_L, - .flags = MOTIONSENSE_FLAG_INT_SIGNAL, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS, - .rot_standard_ref = &base_standard_ref, - .default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs */ - .min_frequency = LSM6DSM_ODR_MIN_VAL, - .max_frequency = LSM6DSM_ODR_MAX_VAL, - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 13000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - /* Sensor on for angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - }, - }, - - [BASE_GYRO] = { - .name = "Base Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_LSM6DSM, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_BASE, - .drv = &lsm6dsm_drv, - .mutex = &g_base_mutex, - .drv_data = LSM6DSM_ST_DATA(lsm6dsm_data, - MOTIONSENSE_TYPE_GYRO), - .int_signal = GPIO_EC_IMU_INT_L, - .flags = MOTIONSENSE_FLAG_INT_SIGNAL, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS, - .default_range = 1000 | ROUND_UP_FLAG, /* dps */ - .rot_standard_ref = &base_standard_ref, - .min_frequency = LSM6DSM_ODR_MIN_VAL, - .max_frequency = LSM6DSM_ODR_MAX_VAL, - }, -}; -unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors); - -/******************************************************************************/ -/* Physical fans. These are logically separate from pwm_channels. */ - -const struct fan_conf fan_conf_0 = { - .flags = FAN_USE_RPM_MODE, - .ch = MFT_CH_0, /* Use MFT id to control fan */ - .pgood_gpio = -1, - .enable_gpio = GPIO_EN_PP5000_FAN, -}; - -/* - * Fan specs from datasheet: - * Max speed 5900 rpm (+/- 7%), minimum duty cycle 30%. - * Minimum speed not specified by RPM. Set minimum RPM to max speed (with - * margin) x 30%. - * 5900 x 1.07 x 0.30 = 1894, round up to 1900 - */ -const struct fan_rpm fan_rpm_0 = { - .rpm_min = 1900, - .rpm_start = 1900, - .rpm_max = 5900, -}; - -const struct fan_t fans[FAN_CH_COUNT] = { - [FAN_CH_0] = { - .conf = &fan_conf_0, - .rpm = &fan_rpm_0, - }, -}; - -/******************************************************************************/ -/* EC thermal management configuration */ - -/* - * Tiger Lake specifies 100 C as maximum TDP temperature. THRMTRIP# occurs at - * 130 C. However, sensor is located next to DDR, so we need to use the lower - * DDR temperature limit (85 C) - */ -const static struct ec_thermal_config thermal_cpu = { - .temp_host = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(70), - [EC_TEMP_THRESH_HALT] = C_TO_K(80), - }, - .temp_host_release = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(65), - }, - .temp_fan_off = C_TO_K(35), - .temp_fan_max = C_TO_K(50), -}; - -/* - * Inductor limits - used for both charger and PP3300 regulator - * - * Need to use the lower of the charger IC, PP3300 regulator, and the inductors - * - * Charger max recommended temperature 100C, max absolute temperature 125C - * PP3300 regulator: operating range -40 C to 145 C - * - * Inductors: limit of 125c - * PCB: limit is 80c - */ -const static struct ec_thermal_config thermal_inductor = { - .temp_host = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(75), - [EC_TEMP_THRESH_HALT] = C_TO_K(80), - }, - .temp_host_release = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(65), - }, - .temp_fan_off = C_TO_K(40), - .temp_fan_max = C_TO_K(55), -}; - - -struct ec_thermal_config thermal_params[] = { - [TEMP_SENSOR_1_CHARGER] = thermal_inductor, - [TEMP_SENSOR_2_PP3300_REGULATOR] = thermal_inductor, - [TEMP_SENSOR_3_DDR_SOC] = thermal_cpu, - [TEMP_SENSOR_4_FAN] = thermal_cpu, -}; -BUILD_ASSERT(ARRAY_SIZE(thermal_params) == TEMP_SENSOR_COUNT); - -/******************************************************************************/ -/* MFT channels. These are logically separate from pwm_channels. */ -const struct mft_t mft_channels[] = { - [MFT_CH_0] = { - .module = NPCX_MFT_MODULE_1, - .clk_src = TCKC_LFCLK, - .pwm_id = PWM_CH_FAN, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(mft_channels) == MFT_CH_COUNT); - -/******************************************************************************/ -/* I2C port map configuration */ -const struct i2c_port_t i2c_ports[] = { - { - .name = "sensor", - .port = I2C_PORT_SENSOR, - .kbps = 400, - .scl = GPIO_EC_I2C0_SENSOR_SCL, - .sda = GPIO_EC_I2C0_SENSOR_SDA, - }, - { - .name = "usb_c0", - .port = I2C_PORT_USB_C0, - .kbps = 1000, - .scl = GPIO_EC_I2C1_USB_C0_SCL, - .sda = GPIO_EC_I2C1_USB_C0_SDA, - }, - { - .name = "usb_c1", - .port = I2C_PORT_USB_C1, - .kbps = 1000, - .scl = GPIO_EC_I2C2_USB_C1_SCL, - .sda = GPIO_EC_I2C2_USB_C1_SDA, - }, - { - .name = "usb_1_mix", - .port = I2C_PORT_USB_1_MIX, - .kbps = 100, - .scl = GPIO_EC_I2C3_USB_1_MIX_SCL, - .sda = GPIO_EC_I2C3_USB_1_MIX_SDA, - }, - { - .name = "power", - .port = I2C_PORT_POWER, - .kbps = 100, - .scl = GPIO_EC_I2C5_POWER_SCL, - .sda = GPIO_EC_I2C5_POWER_SDA, - }, - { - .name = "eeprom", - .port = I2C_PORT_EEPROM, - .kbps = 400, - .scl = GPIO_EC_I2C7_EEPROM_SCL, - .sda = GPIO_EC_I2C7_EEPROM_SDA, - }, -}; -const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports); - -/******************************************************************************/ -/* PWM configuration */ -const struct pwm_t pwm_channels[] = { - [PWM_CH_LED4_SIDESEL] = { - .channel = 7, - .flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, - /* Run at a higher frequency than the color PWM signals to avoid - * timing-based color shifts. - */ - .freq = 4800, - }, - [PWM_CH_FAN] = { - .channel = 5, - .flags = PWM_CONFIG_OPEN_DRAIN, - .freq = 25000 - }, - [PWM_CH_KBLIGHT] = { - .channel = 3, - .flags = 0, - /* - * Set PWM frequency to multiple of 50 Hz and 60 Hz to prevent - * flicker. Higher frequencies consume similar average power to - * lower PWM frequencies, but higher frequencies record a much - * lower maximum power. - */ - .freq = 2400, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT); - -void board_reset_pd_mcu(void) -{ - /* TODO(b/159024035): Malefor: check USB PD reset operation */ -} - -__override void board_cbi_init(void) -{ - /* TODO(b/159024035): Malefor: check FW_CONFIG fields for USB DB type */ -} - -/******************************************************************************/ -/* USBC PPC configuration */ -struct ppc_config_t ppc_chips[] = { - [USBC_PORT_C0] = { - .i2c_port = I2C_PORT_USB_C0, - .i2c_addr_flags = SN5S330_ADDR0_FLAGS, - .drv = &sn5s330_drv, - }, - [USBC_PORT_C1] = { - .i2c_port = I2C_PORT_USB_C1, - .i2c_addr_flags = SYV682X_ADDR0_FLAGS, - .drv = &syv682x_drv, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(ppc_chips) == USBC_PORT_COUNT); -unsigned int ppc_cnt = ARRAY_SIZE(ppc_chips); - -/******************************************************************************/ -/* PPC support routines */ -void ppc_interrupt(enum gpio_signal signal) -{ - switch (signal) { - case GPIO_USB_C0_PPC_INT_ODL: - sn5s330_interrupt(USBC_PORT_C0); - break; - case GPIO_USB_C1_PPC_INT_ODL: - syv682x_interrupt(USBC_PORT_C1); - default: - break; - } -} - -/******************************************************************************/ -/* BC1.2 charger detect configuration */ -const struct pi3usb9201_config_t pi3usb9201_bc12_chips[] = { - [USBC_PORT_C0] = { - .i2c_port = I2C_PORT_USB_C0, - .i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS, - }, - [USBC_PORT_C1] = { - .i2c_port = I2C_PORT_USB_C1, - .i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(pi3usb9201_bc12_chips) == USBC_PORT_COUNT); - -/******************************************************************************/ -/* USBC TCPC configuration */ -struct tcpc_config_t tcpc_config[] = { - [USBC_PORT_C0] = { - .bus_type = EC_BUS_TYPE_I2C, - .i2c_info = { - .port = I2C_PORT_USB_C0, - .addr_flags = TUSB422_I2C_ADDR_FLAGS, - }, - .drv = &tusb422_tcpm_drv, - }, - [USBC_PORT_C1] = { - .bus_type = EC_BUS_TYPE_I2C, - .i2c_info = { - .port = I2C_PORT_USB_C1, - .addr_flags = TUSB422_I2C_ADDR_FLAGS, - }, - .drv = &tusb422_tcpm_drv, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(tcpc_config) == USBC_PORT_COUNT); -BUILD_ASSERT(CONFIG_USB_PD_PORT_MAX_COUNT == USBC_PORT_COUNT); - -/******************************************************************************/ -/* USBC mux configuration - Tiger Lake includes internal mux */ -struct usb_mux usbc1_tcss_usb_mux = { - .usb_port = USBC_PORT_C1, - .driver = &virtual_usb_mux_driver, - .hpd_update = &virtual_hpd_update, -}; -struct usb_mux usb_muxes[] = { - [USBC_PORT_C0] = { - .usb_port = USBC_PORT_C0, - .driver = &virtual_usb_mux_driver, - .hpd_update = &virtual_hpd_update, - }, - [USBC_PORT_C1] = { - .usb_port = USBC_PORT_C1, - .next_mux = &usbc1_tcss_usb_mux, - .driver = &bb_usb_retimer, - .hpd_update = bb_retimer_hpd_update, - .i2c_port = I2C_PORT_USB_1_MIX, - .i2c_addr_flags = USBC_PORT_C1_BB_RETIMER_I2C_ADDR, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(usb_muxes) == USBC_PORT_COUNT); - -struct bb_usb_control bb_controls[] = { - [USBC_PORT_C0] = { - /* USB-C port 0 doesn't have a retimer */ - }, - [USBC_PORT_C1] = { - .usb_ls_en_gpio = GPIO_USB_C1_LS_EN, - .retimer_rst_gpio = GPIO_USB_C1_RT_RST_ODL, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(bb_controls) == USBC_PORT_COUNT); - -static void board_tcpc_init(void) -{ - /* Don't reset TCPCs after initial reset */ - if (!system_jumped_late()) - board_reset_pd_mcu(); - - /* Enable PPC interrupts. */ - gpio_enable_interrupt(GPIO_USB_C0_PPC_INT_ODL); - gpio_enable_interrupt(GPIO_USB_C1_PPC_INT_ODL); - - /* Enable TCPC interrupts. */ - gpio_enable_interrupt(GPIO_USB_C0_TCPC_INT_ODL); - gpio_enable_interrupt(GPIO_USB_C1_TCPC_INT_ODL); - - /* Enable BC1.2 interrupts. */ - gpio_enable_interrupt(GPIO_USB_C0_BC12_INT_ODL); - gpio_enable_interrupt(GPIO_USB_C1_BC12_INT_ODL); -} -DECLARE_HOOK(HOOK_INIT, board_tcpc_init, HOOK_PRIO_INIT_CHIPSET); - -/******************************************************************************/ -/* TCPC support routines */ -uint16_t tcpc_get_alert_status(void) -{ - uint16_t status = 0; - - /* - * Check which port has the ALERT line set - */ - if (!gpio_get_level(GPIO_USB_C0_TCPC_INT_ODL)) - status |= PD_STATUS_TCPC_ALERT_0; - if (!gpio_get_level(GPIO_USB_C1_TCPC_INT_ODL)) - status |= PD_STATUS_TCPC_ALERT_1; - - return status; -} - -int ppc_get_alert_status(int port) -{ - if (port == USBC_PORT_C0) - return gpio_get_level(GPIO_USB_C0_PPC_INT_ODL) == 0; - else - return gpio_get_level(GPIO_USB_C1_PPC_INT_ODL) == 0; -} |