diff options
Diffstat (limited to 'board/link/gpio.inc')
| -rw-r--r-- | board/link/gpio.inc | 158 |
1 files changed, 79 insertions, 79 deletions
diff --git a/board/link/gpio.inc b/board/link/gpio.inc index f4330035d7..bd9b0f2317 100644 --- a/board/link/gpio.inc +++ b/board/link/gpio.inc @@ -6,91 +6,91 @@ */ /* Inputs with interrupt handlers are first for efficiency */ -GPIO_INT(POWER_BUTTON_L, K, 7, GPIO_INT_BOTH, power_button_interrupt) /* Power button */ -GPIO_INT(LID_OPEN, K, 5, GPIO_INT_BOTH, lid_interrupt) /* Lid switch */ -GPIO_INT(AC_PRESENT, H, 3, GPIO_INT_BOTH, extpower_interrupt) /* AC power present */ -GPIO_INT(PCH_BKLTEN, J, 3, GPIO_INT_BOTH, backlight_interrupt) /* Backlight enable signal from PCH */ -GPIO_INT(PCH_SLP_A_L, G, 5, GPIO_INT_BOTH, power_signal_interrupt) /* SLP_A# signal from PCH */ -GPIO_INT(PCH_SLP_ME_CSW_DEV_L, G, 4, GPIO_INT_BOTH, power_signal_interrupt) /* SLP_ME_CSW_DEV# signal from PCH */ -GPIO_INT(PCH_SLP_S3_L, J, 0, GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S3# signal from PCH */ -GPIO_INT(PCH_SLP_S4_L, J, 1, GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S4# signal from PCH */ -GPIO_INT(PCH_SLP_S5_L, J, 2, GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S5# signal from PCH */ -GPIO_INT(PCH_SLP_SUS_L, G, 3, GPIO_INT_BOTH, power_signal_interrupt) /* SLP_SUS# signal from PCH */ -GPIO_INT(PCH_SUSWARN_L, G, 2, GPIO_INT_BOTH, power_interrupt) /* SUSWARN# signal from PCH */ -GPIO_INT(PGOOD_1_5V_DDR, K, 0, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +1.5V_DDR */ -GPIO_INT(PGOOD_1_5V_PCH, K, 1, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +1.5V_PCH */ -GPIO_INT(PGOOD_1_8VS, K, 3, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +1.8VS */ -GPIO_INT(PGOOD_5VALW, H, 0, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +5VALW */ -GPIO_INT(PGOOD_CPU_CORE, M, 3, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +CPU_CORE */ -GPIO_INT(PGOOD_VCCP, K, 2, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +VCCP */ -GPIO_INT(PGOOD_VCCSA, H, 1, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +VCCSA */ -GPIO_INT(PGOOD_VGFX_CORE, D, 2, GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +VGFX_CORE */ -GPIO_INT(RECOVERY_L, H, 7, GPIO_INT_BOTH, switch_interrupt) /* Recovery signal from servo */ -GPIO_INT(WP, J, 4, GPIO_INT_BOTH, switch_interrupt) /* Write protect input */ +GPIO_INT(POWER_BUTTON_L, PIN(K, 7), GPIO_INT_BOTH, power_button_interrupt) /* Power button */ +GPIO_INT(LID_OPEN, PIN(K, 5), GPIO_INT_BOTH, lid_interrupt) /* Lid switch */ +GPIO_INT(AC_PRESENT, PIN(H, 3), GPIO_INT_BOTH, extpower_interrupt) /* AC power present */ +GPIO_INT(PCH_BKLTEN, PIN(J, 3), GPIO_INT_BOTH, backlight_interrupt) /* Backlight enable signal from PCH */ +GPIO_INT(PCH_SLP_A_L, PIN(G, 5), GPIO_INT_BOTH, power_signal_interrupt) /* SLP_A# signal from PCH */ +GPIO_INT(PCH_SLP_ME_CSW_DEV_L, PIN(G, 4), GPIO_INT_BOTH, power_signal_interrupt) /* SLP_ME_CSW_DEV# signal from PCH */ +GPIO_INT(PCH_SLP_S3_L, PIN(J, 0), GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S3# signal from PCH */ +GPIO_INT(PCH_SLP_S4_L, PIN(J, 1), GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S4# signal from PCH */ +GPIO_INT(PCH_SLP_S5_L, PIN(J, 2), GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S5# signal from PCH */ +GPIO_INT(PCH_SLP_SUS_L, PIN(G, 3), GPIO_INT_BOTH, power_signal_interrupt) /* SLP_SUS# signal from PCH */ +GPIO_INT(PCH_SUSWARN_L, PIN(G, 2), GPIO_INT_BOTH, power_interrupt) /* SUSWARN# signal from PCH */ +GPIO_INT(PGOOD_1_5V_DDR, PIN(K, 0), GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +1.5V_DDR */ +GPIO_INT(PGOOD_1_5V_PCH, PIN(K, 1), GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +1.5V_PCH */ +GPIO_INT(PGOOD_1_8VS, PIN(K, 3), GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +1.8VS */ +GPIO_INT(PGOOD_5VALW, PIN(H, 0), GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +5VALW */ +GPIO_INT(PGOOD_CPU_CORE, PIN(M, 3), GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +CPU_CORE */ +GPIO_INT(PGOOD_VCCP, PIN(K, 2), GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +VCCP */ +GPIO_INT(PGOOD_VCCSA, PIN(H, 1), GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +VCCSA */ +GPIO_INT(PGOOD_VGFX_CORE, PIN(D, 2), GPIO_INT_BOTH, power_signal_interrupt) /* Power good on +VGFX_CORE */ +GPIO_INT(RECOVERY_L, PIN(H, 7), GPIO_INT_BOTH, switch_interrupt) /* Recovery signal from servo */ +GPIO_INT(WP, PIN(J, 4), GPIO_INT_BOTH, switch_interrupt) /* Write protect input */ /* Other inputs */ -GPIO(THERMAL_DATA_READY_L, B, 4, GPIO_INPUT) /* Data ready from I2C thermal sensor */ -GPIO(BOARD_VERSION1, H, 6, GPIO_INPUT) /* Board version stuffing resistor 1 */ -GPIO(BOARD_VERSION2, L, 6, GPIO_INPUT) /* Board version stuffing resistor 2 */ -GPIO(BOARD_VERSION3, L, 7, GPIO_INPUT) /* Board version stuffing resistor 3 */ -GPIO(ONEWIRE, H, 2, GPIO_INPUT) /* One-wire bus to adapter LED */ -GPIO(USB1_STATUS_L, E, 7, GPIO_INPUT) /* USB charger port 1 status output */ -GPIO(USB2_STATUS_L, E, 1, GPIO_INPUT) /* USB charger port 2 status output */ +GPIO(THERMAL_DATA_READY_L, PIN(B, 4), GPIO_INPUT) /* Data ready from I2C thermal sensor */ +GPIO(BOARD_VERSION1, PIN(H, 6), GPIO_INPUT) /* Board version stuffing resistor 1 */ +GPIO(BOARD_VERSION2, PIN(L, 6), GPIO_INPUT) /* Board version stuffing resistor 2 */ +GPIO(BOARD_VERSION3, PIN(L, 7), GPIO_INPUT) /* Board version stuffing resistor 3 */ +GPIO(ONEWIRE, PIN(H, 2), GPIO_INPUT) /* One-wire bus to adapter LED */ +GPIO(USB1_STATUS_L, PIN(E, 7), GPIO_INPUT) /* USB charger port 1 status output */ +GPIO(USB2_STATUS_L, PIN(E, 1), GPIO_INPUT) /* USB charger port 2 status output */ /* Outputs; all unasserted by default except for reset signals */ -GPIO(CPU_PROCHOT, F, 2, GPIO_OUT_LOW) /* Force CPU to think it's overheated */ -GPIO(ENABLE_1_5V_DDR, H, 5, GPIO_OUT_LOW) /* Enable +1.5V_DDR supply */ -GPIO(ENABLE_5VALW, K, 4, GPIO_OUT_HIGH) /* Enable +5V always on rail */ -GPIO(ENABLE_BACKLIGHT, H, 4, GPIO_OUT_LOW) /* Enable backlight power */ -GPIO(ENABLE_TOUCHPAD, C, 6, GPIO_OUT_LOW) /* Enable touchpad power */ -GPIO(ENABLE_VCORE, F, 7, GPIO_OUT_LOW) /* Enable +CPU_CORE and +VGFX_CORE */ -GPIO(ENABLE_VS, G, 6, GPIO_OUT_LOW) /* Enable VS power supplies */ -GPIO(ENABLE_WLAN, Q, 5, GPIO_OUT_LOW) /* Enable WLAN module power (+3VS_WLAN) */ -GPIO(ENTERING_RW, J, 5, GPIO_OUT_LOW) /* Indicate when EC is entering RW code */ -GPIO(LIGHTBAR_RESET_L, B, 1, GPIO_OUT_LOW) /* Reset lightbar controllers */ -GPIO(PCH_A20GATE, Q, 6, GPIO_OUT_LOW) /* A20GATE signal to PCH */ -GPIO(PCH_DPWROK, G, 0, GPIO_OUT_LOW) /* DPWROK signal to PCH */ +GPIO(CPU_PROCHOT, PIN(F, 2), GPIO_OUT_LOW) /* Force CPU to think it's overheated */ +GPIO(ENABLE_1_5V_DDR, PIN(H, 5), GPIO_OUT_LOW) /* Enable +1.5V_DDR supply */ +GPIO(ENABLE_5VALW, PIN(K, 4), GPIO_OUT_HIGH) /* Enable +5V always on rail */ +GPIO(ENABLE_BACKLIGHT, PIN(H, 4), GPIO_OUT_LOW) /* Enable backlight power */ +GPIO(ENABLE_TOUCHPAD, PIN(C, 6), GPIO_OUT_LOW) /* Enable touchpad power */ +GPIO(ENABLE_VCORE, PIN(F, 7), GPIO_OUT_LOW) /* Enable +CPU_CORE and +VGFX_CORE */ +GPIO(ENABLE_VS, PIN(G, 6), GPIO_OUT_LOW) /* Enable VS power supplies */ +GPIO(ENABLE_WLAN, PIN(Q, 5), GPIO_OUT_LOW) /* Enable WLAN module power (+3VS_WLAN) */ +GPIO(ENTERING_RW, PIN(J, 5), GPIO_OUT_LOW) /* Indicate when EC is entering RW code */ +GPIO(LIGHTBAR_RESET_L, PIN(B, 1), GPIO_OUT_LOW) /* Reset lightbar controllers */ +GPIO(PCH_A20GATE, PIN(Q, 6), GPIO_OUT_LOW) /* A20GATE signal to PCH */ +GPIO(PCH_DPWROK, PIN(G, 0), GPIO_OUT_LOW) /* DPWROK signal to PCH */ /* * HDA_SDO is technically an output, but we need to leave it as an * input until we drive it high. So can't use open-drain (HI_Z). */ -GPIO(PCH_HDA_SDO, G, 1, GPIO_INPUT) /* HDA_SDO signal to PCH; when high, ME ignores security descriptor */ -GPIO(PCH_WAKE_L, F, 0, GPIO_OUT_HIGH) /* Wake signal output to PCH */ -GPIO(PCH_NMI_L, M, 2, GPIO_OUT_HIGH) /* Non-maskable interrupt pin to PCH */ -GPIO(PCH_PWRBTN_L, G, 7, GPIO_OUT_HIGH) /* Power button output to PCH */ -GPIO(PCH_PWROK, F, 5, GPIO_OUT_LOW) /* PWROK / APWROK signals to PCH */ -GPIO(PCH_RCIN_L, Q, 7, GPIO_ODR_HIGH) /* RCIN# signal to PCH */ -GPIO(PCH_RSMRST_L, F, 1, GPIO_OUT_LOW) /* Reset PCH resume power plane logic */ -GPIO(PCH_RTCRST_L, F, 6, GPIO_ODR_HIGH) /* Reset PCH RTC well */ -GPIO(PCH_SMI_L, F, 4, GPIO_OUT_HIGH) /* System management interrupt to PCH */ -GPIO(PCH_SRTCRST_L, C, 7, GPIO_ODR_HIGH) /* Reset PCH ME RTC well */ -GPIO(PCH_SUSACK_L, F, 3, GPIO_OUT_HIGH) /* Acknowledge PCH SUSWARN# signal */ -GPIO(RADIO_ENABLE_WLAN, D, 0, GPIO_OUT_LOW) /* Enable WLAN radio */ -GPIO(RADIO_ENABLE_BT, D, 1, GPIO_OUT_LOW) /* Enable bluetooth radio */ -GPIO(SPI_CS_L, A, 3, GPIO_ODR_HIGH) /* SPI chip select */ -GPIO(TOUCHSCREEN_RESET_L, B, 0, GPIO_OUT_LOW) /* Reset touch screen */ -GPIO(USB1_CTL1, E, 2, GPIO_OUT_LOW) /* USB charger port 1 CTL1 output */ -GPIO(USB1_CTL2, E, 3, GPIO_OUT_LOW) /* USB charger port 1 CTL2 output */ -GPIO(USB1_CTL3, E, 4, GPIO_OUT_LOW) /* USB charger port 1 CTL3 output */ -GPIO(USB1_ENABLE, E, 5, GPIO_OUT_LOW) /* USB charger port 1 enable */ -GPIO(USB1_ILIM_SEL, E, 6, GPIO_OUT_LOW) /* USB charger port 1 ILIM_SEL output */ -GPIO(USB2_CTL1, D, 4, GPIO_OUT_LOW) /* USB charger port 2 CTL1 output */ -GPIO(USB2_CTL2, D, 5, GPIO_OUT_LOW) /* USB charger port 2 CTL2 output */ -GPIO(USB2_CTL3, D, 6, GPIO_OUT_LOW) /* USB charger port 2 CTL3 output */ -GPIO(USB2_ENABLE, D, 7, GPIO_OUT_LOW) /* USB charger port 2 enable */ -GPIO(USB2_ILIM_SEL, E, 0, GPIO_OUT_LOW) /* USB charger port 2 ILIM_SEL output */ +GPIO(PCH_HDA_SDO, PIN(G, 1), GPIO_INPUT) /* HDA_SDO signal to PCH; when high, ME ignores security descriptor */ +GPIO(PCH_WAKE_L, PIN(F, 0), GPIO_OUT_HIGH) /* Wake signal output to PCH */ +GPIO(PCH_NMI_L, PIN(M, 2), GPIO_OUT_HIGH) /* Non-maskable interrupt pin to PCH */ +GPIO(PCH_PWRBTN_L, PIN(G, 7), GPIO_OUT_HIGH) /* Power button output to PCH */ +GPIO(PCH_PWROK, PIN(F, 5), GPIO_OUT_LOW) /* PWROK / APWROK signals to PCH */ +GPIO(PCH_RCIN_L, PIN(Q, 7), GPIO_ODR_HIGH) /* RCIN# signal to PCH */ +GPIO(PCH_RSMRST_L, PIN(F, 1), GPIO_OUT_LOW) /* Reset PCH resume power plane logic */ +GPIO(PCH_RTCRST_L, PIN(F, 6), GPIO_ODR_HIGH) /* Reset PCH RTC well */ +GPIO(PCH_SMI_L, PIN(F, 4), GPIO_OUT_HIGH) /* System management interrupt to PCH */ +GPIO(PCH_SRTCRST_L, PIN(C, 7), GPIO_ODR_HIGH) /* Reset PCH ME RTC well */ +GPIO(PCH_SUSACK_L, PIN(F, 3), GPIO_OUT_HIGH) /* Acknowledge PCH SUSWARN# signal */ +GPIO(RADIO_ENABLE_WLAN, PIN(D, 0), GPIO_OUT_LOW) /* Enable WLAN radio */ +GPIO(RADIO_ENABLE_BT, PIN(D, 1), GPIO_OUT_LOW) /* Enable bluetooth radio */ +GPIO(SPI_CS_L, PIN(A, 3), GPIO_ODR_HIGH) /* SPI chip select */ +GPIO(TOUCHSCREEN_RESET_L, PIN(B, 0), GPIO_OUT_LOW) /* Reset touch screen */ +GPIO(USB1_CTL1, PIN(E, 2), GPIO_OUT_LOW) /* USB charger port 1 CTL1 output */ +GPIO(USB1_CTL2, PIN(E, 3), GPIO_OUT_LOW) /* USB charger port 1 CTL2 output */ +GPIO(USB1_CTL3, PIN(E, 4), GPIO_OUT_LOW) /* USB charger port 1 CTL3 output */ +GPIO(USB1_ENABLE, PIN(E, 5), GPIO_OUT_LOW) /* USB charger port 1 enable */ +GPIO(USB1_ILIM_SEL, PIN(E, 6), GPIO_OUT_LOW) /* USB charger port 1 ILIM_SEL output */ +GPIO(USB2_CTL1, PIN(D, 4), GPIO_OUT_LOW) /* USB charger port 2 CTL1 output */ +GPIO(USB2_CTL2, PIN(D, 5), GPIO_OUT_LOW) /* USB charger port 2 CTL2 output */ +GPIO(USB2_CTL3, PIN(D, 6), GPIO_OUT_LOW) /* USB charger port 2 CTL3 output */ +GPIO(USB2_ENABLE, PIN(D, 7), GPIO_OUT_LOW) /* USB charger port 2 enable */ +GPIO(USB2_ILIM_SEL, PIN(E, 0), GPIO_OUT_LOW) /* USB charger port 2 ILIM_SEL output */ -ALTERNATE(A, 0x03, 1, MODULE_UART, 0) /* UART0 */ -ALTERNATE(A, 0x40, 3, MODULE_I2C, 0) /* I2C1 SCL */ -ALTERNATE(A, 0x80, 3, MODULE_I2C, GPIO_OPEN_DRAIN) /* I2C1 SDA */ -ALTERNATE(B, 0x04, 3, MODULE_I2C, 0) /* I2C0 SCL */ -ALTERNATE(B, 0x08, 3, MODULE_I2C, GPIO_OPEN_DRAIN) /* I2C0 SDA */ -ALTERNATE(B, 0x40, 3, MODULE_I2C, 0) /* I2C5 SCL */ -ALTERNATE(B, 0x80, 3, MODULE_I2C, GPIO_OPEN_DRAIN) /* I2C5 SDA */ -ALTERNATE(C, 0x30, 2, MODULE_UART, 0) /* UART1 */ -ALTERNATE(J, 0x40, 1, MODULE_PECI, 0) /* PECI Tx */ -ALTERNATE(J, 0x80, 0, MODULE_PECI, GPIO_ANALOG) /* PECI Rx */ -ALTERNATE(K, 0x40, 1, MODULE_PWM_KBLIGHT, 0) /* FAN0PWM1 */ -ALTERNATE(L, 0x3f, 15, MODULE_LPC, 0) /* LPC */ -ALTERNATE(M, 0x33, 15, MODULE_LPC, 0) /* LPC */ -ALTERNATE(M, 0xc0, 1, MODULE_PWM_FAN, 0) /* FAN0PWM0 */ +ALTERNATE(PIN_MASK(A, 0x03), 1, MODULE_UART, 0) /* UART0 */ +ALTERNATE(PIN_MASK(A, 0x40), 3, MODULE_I2C, 0) /* I2C1 SCL */ +ALTERNATE(PIN_MASK(A, 0x80), 3, MODULE_I2C, GPIO_OPEN_DRAIN) /* I2C1 SDA */ +ALTERNATE(PIN_MASK(B, 0x04), 3, MODULE_I2C, 0) /* I2C0 SCL */ +ALTERNATE(PIN_MASK(B, 0x08), 3, MODULE_I2C, GPIO_OPEN_DRAIN) /* I2C0 SDA */ +ALTERNATE(PIN_MASK(B, 0x40), 3, MODULE_I2C, 0) /* I2C5 SCL */ +ALTERNATE(PIN_MASK(B, 0x80), 3, MODULE_I2C, GPIO_OPEN_DRAIN) /* I2C5 SDA */ +ALTERNATE(PIN_MASK(C, 0x30), 2, MODULE_UART, 0) /* UART1 */ +ALTERNATE(PIN_MASK(J, 0x40), 1, MODULE_PECI, 0) /* PECI Tx */ +ALTERNATE(PIN_MASK(J, 0x80), 0, MODULE_PECI, GPIO_ANALOG) /* PECI Rx */ +ALTERNATE(PIN_MASK(K, 0x40), 1, MODULE_PWM_KBLIGHT, 0) /* FAN0PWM1 */ +ALTERNATE(PIN_MASK(L, 0x3f), 15, MODULE_LPC, 0) /* LPC */ +ALTERNATE(PIN_MASK(M, 0x33), 15, MODULE_LPC, 0) /* LPC */ +ALTERNATE(PIN_MASK(M, 0xc0), 1, MODULE_PWM_FAN, 0) /* FAN0PWM0 */ |