diff options
Diffstat (limited to 'board/nucleo-f411re/board.c')
-rw-r--r-- | board/nucleo-f411re/board.c | 124 |
1 files changed, 0 insertions, 124 deletions
diff --git a/board/nucleo-f411re/board.c b/board/nucleo-f411re/board.c deleted file mode 100644 index a177a793ab..0000000000 --- a/board/nucleo-f411re/board.c +++ /dev/null @@ -1,124 +0,0 @@ -/* Copyright 2015 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ -/* nucleo-f411re development board configuration */ - -#include "adc.h" -#include "common.h" -#include "console.h" -#include "driver/accelgyro_bmi_common.h" -#include "ec_version.h" -#include "gpio.h" -#include "hooks.h" -#include "i2c.h" -#include "motion_sense.h" - -#include "gpio.h" -#include "registers.h" -#include "task.h" -#include "util.h" - -void user_button_evt(enum gpio_signal signal) -{ - ccprintf("Button %d, %d!\n", signal, gpio_get_level(signal)); -} - -#include "gpio_list.h" - -/* Initialize board. */ -static void board_init(void) -{ - gpio_enable_interrupt(GPIO_USER_BUTTON_L); - - /* No power control yet */ - /* Go to S3 state */ - hook_notify(HOOK_CHIPSET_STARTUP); - - /* Go to S0 state */ - hook_notify(HOOK_CHIPSET_RESUME); -} -DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT); - -/* ADC channels */ -const struct adc_t adc_channels[] = { - /* Arduino connectors analog pins */ - [ADC1_0] = {"ADC1_0", 3000, 4096, 0, STM32_AIN(0)}, - [ADC1_1] = {"ADC1_1", 3000, 4096, 0, STM32_AIN(1)}, - [ADC1_4] = {"ADC1_4", 3000, 4096, 0, STM32_AIN(4)}, - [ADC1_8] = {"ADC1_8", 3000, 4096, 0, STM32_AIN(8)}, -}; -BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT); - -/* I2C ports */ -const struct i2c_port_t i2c_ports[] = { - {"master", I2C_PORT_MASTER, 100, - GPIO_MASTER_I2C_SCL, GPIO_MASTER_I2C_SDA}, -}; - -const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports); - -/* Base Sensor mutex */ -static struct mutex g_base_mutex; - -static struct bmi_drv_data_t g_bmi160_data; - -struct motion_sensor_t motion_sensors[] = { - [BASE_ACCEL] = { - .name = "Base Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMI160, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_BASE, - .drv = &bmi160_drv, - .mutex = &g_base_mutex, - .drv_data = &g_bmi160_data, - .port = I2C_PORT_ACCEL, - .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS, - .default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs */ - .min_frequency = BMI_ACCEL_MIN_FREQ, - .max_frequency = BMI_ACCEL_MAX_FREQ, - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - /* Sensor on for lid angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - }, - }, - - [BASE_GYRO] = { - .name = "Base Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMI160, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_BASE, - .drv = &bmi160_drv, - .mutex = &g_base_mutex, - .drv_data = &g_bmi160_data, - .port = I2C_PORT_ACCEL, - .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS, - .default_range = 1000, /* dps */ - .min_frequency = BMI_GYRO_MIN_FREQ, - .max_frequency = BMI_GYRO_MAX_FREQ, - }, -}; -const unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors); - -#ifdef CONFIG_DMA_HELP -#include "dma.h" -int command_dma_help(int argc, char **argv) -{ - dma_dump(STM32_DMA2_STREAM0); - dma_test(STM32_DMA2_STREAM0); - dma_dump(STM32_DMA2_STREAM0); - return EC_SUCCESS; -} -DECLARE_CONSOLE_COMMAND(dmahelp, command_dma_help, - NULL, "Run DMA test"); -#endif |