diff options
Diffstat (limited to 'board/servo_v4/usb_pd_config.h')
-rw-r--r-- | board/servo_v4/usb_pd_config.h | 288 |
1 files changed, 0 insertions, 288 deletions
diff --git a/board/servo_v4/usb_pd_config.h b/board/servo_v4/usb_pd_config.h deleted file mode 100644 index b865057618..0000000000 --- a/board/servo_v4/usb_pd_config.h +++ /dev/null @@ -1,288 +0,0 @@ -/* Copyright 2017 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "adc.h" -#include "chip/stm32/registers.h" -#include "console.h" -#include "gpio.h" -#include "ec_commands.h" -#include "usb_pd_tcpm.h" - -/* USB Power delivery board configuration */ - -#ifndef __CROS_EC_USB_PD_CONFIG_H -#define __CROS_EC_USB_PD_CONFIG_H - -/* NOTES: Servo V4 and glados equivalents: - * Glados Servo V4 - * C0 CHG - * C1 DUT - * - */ -#define CHG 0 -#define DUT 1 - -/* Timer selection for baseband PD communication */ -#define TIM_CLOCK_PD_TX_CHG 16 -#define TIM_CLOCK_PD_RX_CHG 1 -#define TIM_CLOCK_PD_TX_DUT 15 -#define TIM_CLOCK_PD_RX_DUT 3 - -/* Timer channel */ -#define TIM_TX_CCR_CHG 1 -#define TIM_RX_CCR_CHG 1 -#define TIM_TX_CCR_DUT 2 -#define TIM_RX_CCR_DUT 1 - -#define TIM_CLOCK_PD_TX(p) ((p) ? TIM_CLOCK_PD_TX_DUT : TIM_CLOCK_PD_TX_CHG) -#define TIM_CLOCK_PD_RX(p) ((p) ? TIM_CLOCK_PD_RX_DUT : TIM_CLOCK_PD_RX_CHG) - -/* RX timer capture/compare register */ -#define TIM_CCR_CHG (&STM32_TIM_CCRx(TIM_CLOCK_PD_RX_CHG, TIM_RX_CCR_CHG)) -#define TIM_CCR_DUT (&STM32_TIM_CCRx(TIM_CLOCK_PD_RX_DUT, TIM_RX_CCR_DUT)) -#define TIM_RX_CCR_REG(p) ((p) ? TIM_CCR_DUT : TIM_CCR_CHG) - -/* TX and RX timer register */ -#define TIM_REG_TX_CHG (STM32_TIM_BASE(TIM_CLOCK_PD_TX_CHG)) -#define TIM_REG_RX_CHG (STM32_TIM_BASE(TIM_CLOCK_PD_RX_CHG)) -#define TIM_REG_TX_DUT (STM32_TIM_BASE(TIM_CLOCK_PD_TX_DUT)) -#define TIM_REG_RX_DUT (STM32_TIM_BASE(TIM_CLOCK_PD_RX_DUT)) -#define TIM_REG_TX(p) ((p) ? TIM_REG_TX_DUT : TIM_REG_TX_CHG) -#define TIM_REG_RX(p) ((p) ? TIM_REG_RX_DUT : TIM_REG_RX_CHG) - -/* use the hardware accelerator for CRC */ -#define CONFIG_HW_CRC - -/* Servo v4 CC configuration */ -#define CC_DETACH BIT(0) /* Emulate detach: both CC open */ -#define CC_DISABLE_DTS BIT(1) /* Apply resistors to single or both CC? */ -#define CC_ALLOW_SRC BIT(2) /* Allow charge through by policy? */ -#define CC_ENABLE_DRP BIT(3) /* Enable dual-role port */ -#define CC_SNK_WITH_PD BIT(4) /* Force enabling PD comm for sink role */ -#define CC_POLARITY BIT(5) /* CC polarity */ - -/* Servo v4 DP alt-mode configuration */ -#define ALT_DP_ENABLE BIT(0) /* Enable DP alt-mode or not */ -#define ALT_DP_PIN_C BIT(1) /* Pin assignment C supported */ -#define ALT_DP_PIN_D BIT(2) /* Pin assignment D supported */ -#define ALT_DP_PIN_E BIT(3) /* Pin assignment E supported */ -#define ALT_DP_MF_PREF BIT(4) /* Multi-Function preferred */ -#define ALT_DP_PLUG BIT(5) /* Plug or receptacle */ -#define ALT_DP_OVERRIDE_HPD BIT(6) /* Override the HPD signal */ -#define ALT_DP_HPD_LVL BIT(7) /* HPD level if overridden */ - -/* TX uses SPI1 on PB3-4 for CHG port, SPI2 on PB 13-14 for DUT port */ -#define SPI_REGS(p) ((p) ? STM32_SPI2_REGS : STM32_SPI1_REGS) -static inline void spi_enable_clock(int port) -{ - if (port == 0) - STM32_RCC_APB2ENR |= STM32_RCC_PB2_SPI1; - else - STM32_RCC_APB1ENR |= STM32_RCC_PB1_SPI2; -} - -/* DMA for transmit uses DMA CH3 for CHG and DMA_CH7 for DUT */ -#define DMAC_SPI_TX(p) ((p) ? STM32_DMAC_CH7 : STM32_DMAC_CH3) - -/* RX uses COMP1 and TIM1_CH1 on port CHG and COMP2 and TIM3_CH1 for port DUT*/ -/* DUT RX use CMP1, TIM3_CH1, DMA_CH6 */ -#define CMP1OUTSEL STM32_COMP_CMP1OUTSEL_TIM3_IC1 -/* CHG RX use CMP2, TIM1_CH1, DMA_CH2 */ -#define CMP2OUTSEL STM32_COMP_CMP2OUTSEL_TIM1_IC1 - -#define TIM_TX_CCR_IDX(p) ((p) ? TIM_TX_CCR_DUT : TIM_TX_CCR_CHG) -#define TIM_RX_CCR_IDX(p) ((p) ? TIM_RX_CCR_DUT : TIM_RX_CCR_CHG) -#define TIM_CCR_CS 1 - -/* - * EXTI line 21 is connected to the CMP1 output, - * EXTI line 22 is connected to the CMP2 output, - * CHG uses CMP2, and DUT uses CMP1. - */ -#define EXTI_COMP_MASK(p) ((p) ? (1<<21) : BIT(22)) - -#define IRQ_COMP STM32_IRQ_COMP -/* triggers packet detection on comparator falling edge */ -#define EXTI_XTSR STM32_EXTI_FTSR - -/* DMA for receive uses DMA_CH2 for CHG and DMA_CH6 for DUT */ -#define DMAC_TIM_RX(p) ((p) ? STM32_DMAC_CH6 : STM32_DMAC_CH2) - -/* the pins used for communication need to be hi-speed */ -static inline void pd_set_pins_speed(int port) -{ - if (port == 0) { - /* 40 MHz pin speed on SPI PB3&4, - * (USB_CHG_TX_CLKIN & USB_CHG_CC1_TX_DATA) - */ - STM32_GPIO_OSPEEDR(GPIO_B) |= 0x000003C0; - /* 40 MHz pin speed on TIM16_CH1 (PB8), - * (USB_CHG_TX_CLKOUT) - */ - STM32_GPIO_OSPEEDR(GPIO_B) |= 0x00030000; - } else { - /* 40 MHz pin speed on SPI PB13/14, - * (USB_DUT_TX_CLKIN & USB_DUT_CC1_TX_DATA) - */ - STM32_GPIO_OSPEEDR(GPIO_B) |= 0x3C000000; - /* 40 MHz pin speed on TIM15_CH2 (PB15) */ - STM32_GPIO_OSPEEDR(GPIO_B) |= 0xC0000000; - } -} - -/* Reset SPI peripheral used for TX */ -static inline void pd_tx_spi_reset(int port) -{ - if (port == 0) { - /* Reset SPI1 */ - STM32_RCC_APB2RSTR |= BIT(12); - STM32_RCC_APB2RSTR &= ~BIT(12); - } else { - /* Reset SPI2 */ - STM32_RCC_APB1RSTR |= BIT(14); - STM32_RCC_APB1RSTR &= ~BIT(14); - } -} - -static const uint8_t tx_gpio[2 /* port */][2 /* polarity */] = { - { GPIO_USB_CHG_CC1_TX_DATA, GPIO_USB_CHG_CC2_TX_DATA }, - { GPIO_USB_DUT_CC1_TX_DATA, GPIO_USB_DUT_CC2_TX_DATA }, -}; -static const uint8_t ref_gpio[2 /* port */][2 /* polarity */] = { - { GPIO_USB_CHG_CC1_PD, GPIO_USB_CHG_CC2_PD }, - { GPIO_USB_DUT_CC1_PD, GPIO_USB_DUT_CC2_PD }, -}; - -/* Drive the CC line from the TX block */ -static inline void pd_tx_enable(int port, int polarity) -{ -#ifndef VIF_BUILD /* genvif doesn't like tricks with GPIO macros */ - const struct gpio_info *tx = gpio_list + tx_gpio[port][polarity]; - const struct gpio_info *ref = gpio_list + ref_gpio[port][polarity]; - - /* use directly GPIO registers, latency before the PD preamble is key */ - - /* switch the TX pin Mode from Input (00) to Alternate (10) for SPI */ - STM32_GPIO_MODER(tx->port) |= 2 << ((31 - __builtin_clz(tx->mask)) * 2); - /* switch the ref pin Mode from analog (11) to Out (01) for low level */ - STM32_GPIO_MODER(ref->port) &= - ~(2 << ((31 - __builtin_clz(ref->mask)) * 2)); -#endif /* !VIF_BUILD */ -} - -/* Put the TX driver in Hi-Z state */ -static inline void pd_tx_disable(int port, int polarity) -{ - const struct gpio_info *tx = gpio_list + tx_gpio[port][polarity]; - const struct gpio_info *ref = gpio_list + ref_gpio[port][polarity]; - - gpio_set_flags_by_mask(tx->port, tx->mask, GPIO_INPUT); - gpio_set_flags_by_mask(ref->port, ref->mask, GPIO_ANALOG); -} - -/* we know the plug polarity, do the right configuration */ -static inline void pd_select_polarity(int port, int polarity) -{ - uint32_t val = STM32_COMP_CSR; - - /* Use window mode so that COMP1 and COMP2 share non-inverting input */ - val |= STM32_COMP_CMP1EN | STM32_COMP_CMP2EN | STM32_COMP_WNDWEN; - - if (port == 0) { - /* CHG use the right comparator inverted input for COMP2 */ - STM32_COMP_CSR = (val & ~STM32_COMP_CMP2INSEL_MASK) | - (polarity ? STM32_COMP_CMP2INSEL_INM4 /* PA4: C0_CC2 */ - : STM32_COMP_CMP2INSEL_INM6);/* PA2: C0_CC1 */ - } else { - /* DUT use the right comparator inverted input for COMP1 */ - STM32_COMP_CSR = (val & ~STM32_COMP_CMP1INSEL_MASK) | - (polarity ? STM32_COMP_CMP1INSEL_INM5 /* PA5: C1_CC2 */ - : STM32_COMP_CMP1INSEL_INM6);/* PA0: C1_CC1 */ - } -} - -/* Initialize pins used for TX and put them in Hi-Z */ -static inline void pd_tx_init(void) -{ - const struct gpio_info *c2 = gpio_list + GPIO_USB_CHG_CC2_TX_DATA; - const struct gpio_info *c1 = gpio_list + GPIO_USB_CHG_CC1_TX_DATA; - const struct gpio_info *d2 = gpio_list + GPIO_USB_DUT_CC2_TX_DATA; - const struct gpio_info *d1 = gpio_list + GPIO_USB_DUT_CC1_TX_DATA; - - gpio_config_module(MODULE_USB_PD, 1); - /* Select the proper alternate SPI function on TX_DATA pins */ - /* USB_CHG_CC2_TX_DATA: PA6 is SPI1 MISO (AF0) */ - gpio_set_alternate_function(c2->port, c2->mask, 0); - gpio_set_flags_by_mask(c2->port, c2->mask, GPIO_INPUT); - /* USB_CHG_CC1_TX_DATA: PB4 is SPI1 MISO (AF0) */ - gpio_set_alternate_function(c1->port, c1->mask, 0); - gpio_set_flags_by_mask(c1->port, c1->mask, GPIO_INPUT); - /* USB_DUT_CC2_TX_DATA: PC2 is SPI2 MISO (AF1) */ - gpio_set_alternate_function(d2->port, d2->mask, 1); - gpio_set_flags_by_mask(d2->port, d2->mask, GPIO_INPUT); - /* USB_DUT_CC1_TX_DATA: PB14 is SPI2 MISO (AF0) */ - gpio_set_alternate_function(d1->port, d1->mask, 0); - gpio_set_flags_by_mask(d1->port, d1->mask, GPIO_INPUT); -} - -static inline void pd_set_host_mode(int port, int enable) -{ - /* - * CHG (port == 0) port has fixed Rd attached and therefore can only - * present as a SNK device. If port != DUT (port == 1), then nothing to - * do in this function. - */ - if (!port) - return; - - if (enable) { - /* - * Servo_v4 in SRC mode acts as a DTS (debug test - * accessory) and needs to present Rp on both CC - * lines. In order to support orientation detection, and - * advertise the correct TypeC current level, the - * values of Rp1/Rp2 need to asymmetric with Rp1 > Rp2. This - * function is called without a specified Rp value so assume the - * servo_v4 default of USB level current. If a higher current - * can be supported, then the Rp value will get adjusted when - * VBUS is enabled. - */ - pd_set_rp_rd(port, TYPEC_CC_RP, TYPEC_RP_USB); - - gpio_set_flags(GPIO_USB_DUT_CC1_TX_DATA, GPIO_INPUT); - gpio_set_flags(GPIO_USB_DUT_CC2_TX_DATA, GPIO_INPUT); - } else { - /* Select Rd, the Rp value is a don't care */ - pd_set_rp_rd(port, TYPEC_CC_RD, TYPEC_RP_RESERVED); - } -} - -/** - * Initialize various GPIOs and interfaces to safe state at start of pd_task. - * - * These include: - * VBUS, charge path based on power role. - * Physical layer CC transmit. - * - * @param port USB-C port number - * @param power_role Power role of device - */ -static inline void pd_config_init(int port, uint8_t power_role) -{ - /* - * Set CC pull resistors. The PD state machine will then transit and - * enable VBUS after it detects valid voltages on CC lines. - */ - pd_set_host_mode(port, power_role); - - /* Initialize TX pins and put them in Hi-Z */ - pd_tx_init(); - -} - -int pd_adc_read(int port, int cc); - -#endif /* __CROS_EC_USB_PD_CONFIG_H */ - |