diff options
Diffstat (limited to 'board/spring/gpio.inc')
| -rw-r--r-- | board/spring/gpio.inc | 91 |
1 files changed, 45 insertions, 46 deletions
diff --git a/board/spring/gpio.inc b/board/spring/gpio.inc index b49270ebbc..eedef23fbc 100644 --- a/board/spring/gpio.inc +++ b/board/spring/gpio.inc @@ -7,60 +7,59 @@ /* Inputs with interrupt handlers are first for efficiency */ /* Keyboard power button */ -GPIO(KB_PWR_ON_L, B, 5, GPIO_INT_BOTH, power_signal_interrupt) -GPIO(PP1800_LDO2, A, 1, GPIO_INT_BOTH, power_signal_interrupt) /* LDO2 is ON (end of PMIC sequence) */ -GPIO(SOC1V8_XPSHOLD, A, 3, GPIO_INT_BOTH, power_signal_interrupt) /* App Processor ON */ -GPIO(CHARGER_INT_L, C, 4, GPIO_INT_FALLING, pmu_irq_handler) -GPIO(LID_OPEN, C, 13, GPIO_INT_BOTH, lid_interrupt) /* LID switch detection */ -GPIO(SUSPEND_L, A, 7, INT_BOTH_FLOATING, power_signal_interrupt) /* AP suspend/resume state */ +GPIO_INT(KB_PWR_ON_L, B, 5, GPIO_INT_BOTH, power_signal_interrupt) +GPIO_INT(PP1800_LDO2, A, 1, GPIO_INT_BOTH, power_signal_interrupt) /* LDO2 is ON (end of PMIC sequence) */ +GPIO_INT(SOC1V8_XPSHOLD, A, 3, GPIO_INT_BOTH, power_signal_interrupt) /* App Processor ON */ +GPIO_INT(CHARGER_INT_L, C, 4, GPIO_INT_FALLING, pmu_irq_handler) +GPIO_INT(LID_OPEN, C, 13, GPIO_INT_BOTH, lid_interrupt) /* LID switch detection */ +GPIO_INT(SUSPEND_L, A, 7, INT_BOTH_FLOATING, power_signal_interrupt) /* AP suspend/resume state */ /* Keyboard inputs */ -GPIO(KB_IN00, C, 8, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) -GPIO(KB_IN01, C, 9, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) -GPIO(KB_IN02, C, 10, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) -GPIO(KB_IN03, C, 11, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) -GPIO(KB_IN04, C, 12, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) -GPIO(KB_IN05, C, 14, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) -GPIO(KB_IN06, C, 15, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) -GPIO(KB_IN07, D, 2, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) -GPIO(USB_CHG_INT, A, 6, GPIO_INT_FALLING, extpower_interrupt) - -GPIO(WP_L, A, 13, GPIO_INPUT, NULL) /* Write protection pin (low active) */ +GPIO_INT(KB_IN00, C, 8, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) +GPIO_INT(KB_IN01, C, 9, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) +GPIO_INT(KB_IN02, C, 10, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) +GPIO_INT(KB_IN03, C, 11, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) +GPIO_INT(KB_IN04, C, 12, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) +GPIO_INT(KB_IN05, C, 14, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) +GPIO_INT(KB_IN06, C, 15, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) +GPIO_INT(KB_IN07, D, 2, GPIO_KB_INPUT, keyboard_raw_gpio_interrupt) +GPIO_INT(USB_CHG_INT, A, 6, GPIO_INT_FALLING, extpower_interrupt) /* Other inputs */ -GPIO(BCHGR_VACG, A, 0, GPIO_INT_BOTH, NULL) /* AC good on TPSChrome */ +GPIO(BCHGR_VACG, A, 0, GPIO_INT_BOTH) /* AC good on TPSChrome */ +GPIO(WP_L, A, 13, GPIO_INPUT) /* Write protection pin (low active) */ /* * I2C pins should be configured as inputs until I2C module is * initialized. This will avoid driving the lines unintentionally. */ -GPIO(I2C1_SCL, B, 6, GPIO_INPUT, NULL) -GPIO(I2C1_SDA, B, 7, GPIO_INPUT, NULL) -GPIO(I2C2_SCL, B, 10, GPIO_INPUT, NULL) -GPIO(I2C2_SDA, B, 11, GPIO_INPUT, NULL) +GPIO(I2C1_SCL, B, 6, GPIO_INPUT) +GPIO(I2C1_SDA, B, 7, GPIO_INPUT) +GPIO(I2C2_SCL, B, 10, GPIO_INPUT) +GPIO(I2C2_SDA, B, 11, GPIO_INPUT) /* Outputs */ -GPIO(EN_PP1350, A, 14, GPIO_OUT_LOW, NULL) /* DDR 1.35v rail enable */ -GPIO(EN_PP5000, A, 11, GPIO_OUT_LOW, NULL) /* 5.0v rail enable */ -GPIO(EN_PP3300, A, 8, GPIO_OUT_LOW, NULL) /* 3.3v rail enable */ -GPIO(PMIC_PWRON_L,A, 12, GPIO_OUT_HIGH, NULL) /* 5v rail ready */ -GPIO(PMIC_RESET, A, 15, GPIO_OUT_LOW, NULL) /* Force hard reset of the pmic */ -GPIO(ENTERING_RW, D, 0, GPIO_OUT_LOW, NULL) /* EC is R/W mode for the kbc mux */ -GPIO(CHARGER_EN, B, 2, GPIO_OUT_LOW, NULL) -GPIO(EC_INT, B, 9, GPIO_ODR_HIGH, NULL) -GPIO(ID_MUX, D, 1, GPIO_OUT_LOW, NULL) -GPIO(KB_OUT00, B, 0, GPIO_KB_OUTPUT, NULL) -GPIO(KB_OUT01, B, 8, GPIO_KB_OUTPUT, NULL) -GPIO(KB_OUT02, B, 12, GPIO_KB_OUTPUT, NULL) -GPIO(KB_OUT03, B, 13, GPIO_KB_OUTPUT, NULL) -GPIO(KB_OUT04, B, 14, GPIO_KB_OUTPUT, NULL) -GPIO(KB_OUT05, B, 15, GPIO_KB_OUTPUT, NULL) -GPIO(KB_OUT06, C, 0, GPIO_KB_OUTPUT, NULL) -GPIO(KB_OUT07, C, 1, GPIO_KB_OUTPUT, NULL) -GPIO(KB_OUT08, C, 2, GPIO_KB_OUTPUT, NULL) -GPIO(KB_OUT09, B, 1, GPIO_KB_OUTPUT, NULL) -GPIO(KB_OUT10, C, 5, GPIO_KB_OUTPUT, NULL) -GPIO(KB_OUT11, C, 6, GPIO_KB_OUTPUT, NULL) -GPIO(KB_OUT12, C, 7, GPIO_KB_OUTPUT, NULL) -GPIO(BOOST_EN, B, 3, GPIO_OUT_HIGH, NULL) -GPIO(ILIM, B, 4, GPIO_OUT_LOW, NULL) +GPIO(EN_PP1350, A, 14, GPIO_OUT_LOW) /* DDR 1.35v rail enable */ +GPIO(EN_PP5000, A, 11, GPIO_OUT_LOW) /* 5.0v rail enable */ +GPIO(EN_PP3300, A, 8, GPIO_OUT_LOW) /* 3.3v rail enable */ +GPIO(PMIC_PWRON_L,A, 12, GPIO_OUT_HIGH) /* 5v rail ready */ +GPIO(PMIC_RESET, A, 15, GPIO_OUT_LOW) /* Force hard reset of the pmic */ +GPIO(ENTERING_RW, D, 0, GPIO_OUT_LOW) /* EC is R/W mode for the kbc mux */ +GPIO(CHARGER_EN, B, 2, GPIO_OUT_LOW) +GPIO(EC_INT, B, 9, GPIO_ODR_HIGH) +GPIO(ID_MUX, D, 1, GPIO_OUT_LOW) +GPIO(KB_OUT00, B, 0, GPIO_KB_OUTPUT) +GPIO(KB_OUT01, B, 8, GPIO_KB_OUTPUT) +GPIO(KB_OUT02, B, 12, GPIO_KB_OUTPUT) +GPIO(KB_OUT03, B, 13, GPIO_KB_OUTPUT) +GPIO(KB_OUT04, B, 14, GPIO_KB_OUTPUT) +GPIO(KB_OUT05, B, 15, GPIO_KB_OUTPUT) +GPIO(KB_OUT06, C, 0, GPIO_KB_OUTPUT) +GPIO(KB_OUT07, C, 1, GPIO_KB_OUTPUT) +GPIO(KB_OUT08, C, 2, GPIO_KB_OUTPUT) +GPIO(KB_OUT09, B, 1, GPIO_KB_OUTPUT) +GPIO(KB_OUT10, C, 5, GPIO_KB_OUTPUT) +GPIO(KB_OUT11, C, 6, GPIO_KB_OUTPUT) +GPIO(KB_OUT12, C, 7, GPIO_KB_OUTPUT) +GPIO(BOOST_EN, B, 3, GPIO_OUT_HIGH) +GPIO(ILIM, B, 4, GPIO_OUT_LOW) |