diff options
Diffstat (limited to 'board/voema/board.h')
-rw-r--r-- | board/voema/board.h | 201 |
1 files changed, 0 insertions, 201 deletions
diff --git a/board/voema/board.h b/board/voema/board.h deleted file mode 100644 index ce91eab712..0000000000 --- a/board/voema/board.h +++ /dev/null @@ -1,201 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Volteer board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* Baseboard features */ -#include "baseboard.h" - -#ifdef BOARD_VOEMA -/* - * The RAM and flash size combination on the the NPCX797FC does not leave - * any unused flash space that can be used to store the .init_rom section. - */ -#undef CONFIG_CHIP_INIT_ROM_REGION -#endif - -#define CONFIG_VBOOT_EFS2 - -#define CONFIG_POWER_BUTTON - -#undef CONFIG_UART_TX_BUF_SIZE -#define CONFIG_UART_TX_BUF_SIZE 4096 - -/* Chipset features */ -#define CONFIG_POWER_PP5000_CONTROL - -/* LED defines */ -#define CONFIG_LED_ONOFF_STATES - -/* Keyboard features */ -#define CONFIG_KEYBOARD_FACTORY_TEST -#define CONFIG_KEYBOARD_VIVALDI -#define CONFIG_KEYBOARD_REFRESH_ROW3 - -/* Sensors */ -/* BMA253 accelerometer in base */ -#define CONFIG_ACCEL_BMA255 -#define CONFIG_ACCELGYRO_ICM426XX -#define CONFIG_ACCELGYRO_ICM426XX_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) -#define CONFIG_ACCEL_KX022 - -/* TCS3400 ALS */ -#define CONFIG_ALS -#define ALS_COUNT 1 -#define CONFIG_ALS_TCS3400 -#define CONFIG_ALS_TCS3400_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(CLEAR_ALS) - -/* Sensors without hardware FIFO are in forced mode */ -#ifdef BOARD_VOEMA_NPCX796FC -#define CONFIG_ACCEL_FORCE_MODE_MASK \ - (BIT(LID_ACCEL) | BIT(CLEAR_ALS) | BIT(BASE_ACCEL)) -#else -#define CONFIG_ACCEL_FORCE_MODE_MASK (board_accel_force_mode_mask()) -#endif - -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_UPDATE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL - -/* USB Type C and USB PD defines */ -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 - -/* TODO: b/144165680 - measure and check these values on Volteer */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ - -/* - * SN5S30 PPC supports up to 24V VBUS source and sink, however passive USB-C - * cables only support up to 60W. - */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 65000 -#define PD_MAX_CURRENT_MA 3250 -#define PD_MAX_VOLTAGE_MV 20000 - -/* Enabling Thunderbolt-compatible mode */ -#define CONFIG_USB_PD_TBT_COMPAT_MODE - -/* USB Type A Features */ -#define USB_PORT_COUNT 1 -#define CONFIG_USB_PORT_POWER_DUMB - -/* USBC PPC*/ -#undef CONFIG_SYV682X_HV_ILIM -#define CONFIG_SYV682X_HV_ILIM SYV682X_HV_ILIM_5_50 -#define CONFIG_USBC_PPC_SYV682X /* USBC port C0/C1 */ -#define CONFIG_USB_PD_FRS_PPC -#undef CONFIG_USB_PD_TCPC_RUNTIME_CONFIG -#undef CONFIG_USB_PD_TCPM_TUSB422 -#undef CONFIG_USB_MUX_RUNTIME_CONFIG - -/* BC 1.2 */ - -/* Volume Button feature */ - -/* Fan features */ -#undef CONFIG_FANS - -/* charger defines */ -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 - -/* Retimer */ -#undef CONFIG_USBC_RETIMER_INTEL_BB -#undef CONFIG_USBC_RETIMER_INTEL_BB_RUNTIME_CONFIG - -/* - * Macros for GPIO signals used in common code that don't match the - * schematic names. Signal names in gpio.inc match the schematic and are - * then redefined here to so it's more clear which signal is being used for - * which purpose. - */ -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL -#define GPIO_EN_PP5000 GPIO_EN_PP5000_A -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_LID_OPEN GPIO_EC_LID_OPEN -#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV -#define GPIO_PACKET_MODE_EN GPIO_EC_H1_PACKET_MODE -#define GPIO_PCH_WAKE_L GPIO_EC_PCH_WAKE_ODL -#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL -#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_ODL -#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST -#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GPIO_PCH_DSW_PWROK GPIO_EC_PCH_DSW_PWROK -#define GPIO_POWER_BUTTON_L GPIO_H1_EC_PWR_BTN_ODL -#define GPIO_RSMRST_L_PGOOD GPIO_PG_EC_RSMRST_ODL -#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL -#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL -#define GPIO_WP_L GPIO_EC_WP_L -#define GPIO_USB_C1_BC12_INT_ODL GPIO_USB_C1_MIX_INT_ODL -#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL -#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL -#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L - -/* I2C Bus Configuration */ -#define CONFIG_I2C -#define I2C_PORT_ACCEL I2C_PORT_SENSOR -#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 -#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0 -#define I2C_PORT_USB_C1 NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_1_MIX NPCX_I2C_PORT3_0 -#define I2C_PORT_POWER NPCX_I2C_PORT5_0 -#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 - -#define I2C_PORT_BATTERY I2C_PORT_POWER -#define I2C_PORT_CHARGER I2C_PORT_EEPROM - -#define I2C_ADDR_EEPROM_FLAGS 0x50 -#define CONFIG_I2C_CONTROLLER - - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -enum battery_type { - BATTERY_LGC011, - BATTERY_PANASONIC_AP15O5L, - BATTERY_TYPE_COUNT, -}; - -enum pwm_channel { - PWM_CH_KBLIGHT, - PWM_CH_COUNT -}; - -enum sensor_id { - LID_ACCEL = 0, - BASE_ACCEL, - BASE_GYRO, - CLEAR_ALS, - RGB_ALS, - SENSOR_COUNT, -}; - -enum usbc_port { - USBC_PORT_C0 = 0, - USBC_PORT_C1, - USBC_PORT_COUNT -}; - -void board_reset_pd_mcu(void); -#ifndef BOARD_VOEMA_NPCX796FC -void motion_interrupt(enum gpio_signal signal); -int board_accel_force_mode_mask(void); -#endif - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ |