diff options
Diffstat (limited to 'board/volet/board.h')
-rw-r--r-- | board/volet/board.h | 199 |
1 files changed, 199 insertions, 0 deletions
diff --git a/board/volet/board.h b/board/volet/board.h new file mode 100644 index 0000000000..6793f4ae9f --- /dev/null +++ b/board/volet/board.h @@ -0,0 +1,199 @@ +/* Copyright 2021 The Chromium OS Authors. All rights reserved. + * Use of this source code is governed by a BSD-style license that can be + * found in the LICENSE file. + */ + +/* Volteer board configuration */ + +#ifndef __CROS_EC_BOARD_H +#define __CROS_EC_BOARD_H + +/* Baseboard features */ +#include "baseboard.h" + +/* Optional features */ +#undef NPCX7_PWM1_SEL +#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */ + +/* + * The RAM and flash size combination on the the NPCX797FC does not leave + * any unused flash space that can be used to store the .init_rom section. + */ +#undef CONFIG_CHIP_INIT_ROM_REGION + +#define CONFIG_VBOOT_EFS2 + +#define CONFIG_POWER_BUTTON + +#undef CONFIG_UART_TX_BUF_SIZE +#define CONFIG_UART_TX_BUF_SIZE 4096 + +/* Chipset features */ +#define CONFIG_POWER_PP5000_CONTROL + +/* LED defines */ +#define CONFIG_LED_ONOFF_STATES + +/* Keyboard features */ +#define CONFIG_KEYBOARD_REFRESH_ROW3 + +/* Keyboard backliht */ +#define CONFIG_PWM +#define CONFIG_PWM_KBLIGHT + +/* Sensors */ +#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT +/* BMI160 Base accel/gyro */ +#define CONFIG_ACCELGYRO_BMI160 +#define CONFIG_ACCELGYRO_ICM426XX /* Base accel second source*/ +#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ + TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) +#define CONFIG_ACCELGYRO_ICM426XX_INT_EVENT \ + TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) + +/* Lid operates in forced mode, base in FIFO */ +#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL) + +/* BMA253 Lid accel */ +#define CONFIG_ACCEL_KX022 /* Lid accel */ +#define CONFIG_ACCEL_BMA255 +#define CONFIG_LID_ANGLE +#define CONFIG_LID_ANGLE_UPDATE +#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL +#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL + +/* USB Type C and USB PD defines */ +#define CONFIG_USB_PD_PORT_MAX_COUNT 2 + +#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ +#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ + +/* + * SN5S30 PPC supports up to 24V VBUS source and sink, however passive USB-C + * cables only support up to 60W. + */ +#define PD_OPERATING_POWER_MW 15000 +#define PD_MAX_POWER_MW 60000 +#define PD_MAX_CURRENT_MA 3000 +#define PD_MAX_VOLTAGE_MV 20000 + +#define CONFIG_USB_PD_REQUIRE_AP_MODE_ENTRY +#ifdef BOARD_VOXEL_ECMODEENTRY +#undef CONFIG_USB_PD_REQUIRE_AP_MODE_ENTRY +#endif + +/* Enabling Thunderbolt-compatible mode */ +#define CONFIG_USB_PD_TBT_COMPAT_MODE + +/* Enabling USB4 mode */ +#define CONFIG_USB_PD_USB4 +#define USBC_PORT_C0_BB_RETIMER_I2C_ADDR 0x40 +#define USBC_PORT_C1_BB_RETIMER_I2C_ADDR 0x41 + +/* USB Type A Features */ +#define USB_PORT_COUNT 1 +#define CONFIG_USB_PORT_POWER_DUMB + +/* USBC PPC*/ +#define CONFIG_USBC_PPC_SYV682X /* USBC port C0/C1 */ +#define CONFIG_USB_PD_FRS_PPC + +/* BC 1.2 */ + +/* TCPC */ +#define CONFIG_USB_PD_TCPM_RT1715 + +/* Volume Button feature */ + +/* Fan features */ + +/* charger defines */ +#define CONFIG_CHARGER_SENSE_RESISTOR 10 +#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 + +/* + * Macros for GPIO signals used in common code that don't match the + * schematic names. Signal names in gpio.inc match the schematic and are + * then redefined here to so it's more clear which signal is being used for + * which purpose. + */ +#define GPIO_AC_PRESENT GPIO_ACOK_OD +#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL +#define GPIO_EN_PP5000 GPIO_EN_PP5000_A +#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW +#define GPIO_LID_OPEN GPIO_EC_LID_OPEN +#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV +#define GPIO_PACKET_MODE_EN GPIO_EC_H1_PACKET_MODE +#define GPIO_PCH_WAKE_L GPIO_EC_PCH_WAKE_ODL +#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL +#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_ODL +#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST +#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L +#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L +#define GPIO_PCH_DSW_PWROK GPIO_EC_PCH_DSW_PWROK +#define GPIO_POWER_BUTTON_L GPIO_H1_EC_PWR_BTN_ODL +#define GPIO_RSMRST_L_PGOOD GPIO_PG_EC_RSMRST_ODL +#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL +#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL +#define GPIO_WP_L GPIO_EC_WP_L +#define GPIO_USB_C1_BC12_INT_ODL GPIO_USB_C1_MIX_INT_ODL +#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL +#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL +#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L + +/* I2C Bus Configuration */ +#define CONFIG_I2C +#define I2C_PORT_ACCEL I2C_PORT_SENSOR +#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 +#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0 +#define I2C_PORT_USB_C1 NPCX_I2C_PORT2_0 +#define I2C_PORT_USB_0_MIX NPCX_I2C_PORT3_0 +#define I2C_PORT_USB_1_MIX NPCX_I2C_PORT4_1 +#define I2C_PORT_POWER NPCX_I2C_PORT5_0 +#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 + +#define I2C_PORT_BATTERY I2C_PORT_POWER +#define I2C_PORT_CHARGER I2C_PORT_EEPROM + +#define I2C_ADDR_EEPROM_FLAGS 0x50 +#define CONFIG_I2C_CONTROLLER + + +#ifndef __ASSEMBLER__ + +#include "gpio_signal.h" +#include "registers.h" + +enum battery_type { + BATTERY_AP19B8M, + BATTERY_LGC_AP18C8K, + BATTERY_COSMX_AP20CBL, + BATTERY_TYPE_COUNT, +}; + +enum pwm_channel { + PWM_CH_FAN, + PWM_CH_KBLIGHT, + PWM_CH_COUNT +}; + +enum sensor_id { + LID_ACCEL = 0, + BASE_ACCEL, + BASE_GYRO, + SENSOR_COUNT, +}; + +enum usbc_port { + USBC_PORT_C0 = 0, + USBC_PORT_C1, + USBC_PORT_COUNT +}; + +void board_reset_pd_mcu(void); + +void motion_interrupt(enum gpio_signal signal); + +#endif /* !__ASSEMBLER__ */ + +#endif /* __CROS_EC_BOARD_H */ |