diff options
Diffstat (limited to 'board/volteer/board.c')
-rw-r--r-- | board/volteer/board.c | 247 |
1 files changed, 0 insertions, 247 deletions
diff --git a/board/volteer/board.c b/board/volteer/board.c deleted file mode 100644 index 8c1be1bf64..0000000000 --- a/board/volteer/board.c +++ /dev/null @@ -1,247 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Volteer board-specific configuration */ -#include "button.h" -#include "common.h" -#include "accelgyro.h" -#include "cbi_ec_fw_config.h" -#include "driver/accel_bma2x2.h" -#include "driver/accelgyro_bmi260.h" -#include "driver/als_tcs3400.h" -#include "driver/retimer/bb_retimer_public.h" -#include "driver/sync.h" -#include "driver/tcpm/ps8xxx.h" -#include "extpower.h" -#include "fan.h" -#include "fan_chip.h" -#include "gpio.h" -#include "hooks.h" -#include "keyboard_scan.h" -#include "lid_switch.h" -#include "power.h" -#include "power_button.h" -#include "pwm.h" -#include "pwm_chip.h" -#include "switch.h" -#include "system.h" -#include "task.h" -#include "tablet_mode.h" -#include "throttle_ap.h" -#include "timer.h" -#include "uart.h" -#include "usb_pd.h" -#include "usb_pd_tbt.h" -#include "usb_pd_tcpm.h" -#include "util.h" - -#include "gpio_list.h" /* Must come after other header files. */ - -#define CPRINTS(format, args...) cprints(CC_CHIPSET, format, ## args) - -/******************************************************************************/ -/* Keyboard scan setting */ -__override struct keyboard_scan_config keyscan_config = { - /* Increase from 50 us, because KSO_02 passes through the H1. */ - .output_settle_us = 80, - /* Other values should be the same as the default configuration. */ - .debounce_down_us = 9 * MSEC, - .debounce_up_us = 30 * MSEC, - .scan_period_us = 3 * MSEC, - .min_post_scan_delay_us = 1000, - .poll_timeout_us = 100 * MSEC, - .actual_key_mask = { - 0x14, 0xff, 0xff, 0xff, 0xff, 0xf5, 0xff, - 0xa4, 0xff, 0xfe, 0x55, 0xfa, 0xca /* full set */ - }, -}; - -/******************************************************************************/ -/* Physical fans. These are logically separate from pwm_channels. */ - -const struct fan_conf fan_conf_0 = { - .flags = FAN_USE_RPM_MODE, - .ch = MFT_CH_0, /* Use MFT id to control fan */ - .pgood_gpio = -1, - .enable_gpio = GPIO_EN_PP5000_FAN, -}; - -/* - * Fan specs from datasheet: - * Max speed 5900 rpm (+/- 7%), minimum duty cycle 30%. - * Minimum speed not specified by RPM. Set minimum RPM to max speed (with - * margin) x 30%. - * 5900 x 1.07 x 0.30 = 1894, round up to 1900 - */ -const struct fan_rpm fan_rpm_0 = { - .rpm_min = 1900, - .rpm_start = 1900, - .rpm_max = 5900, -}; - -const struct fan_t fans[FAN_CH_COUNT] = { - [FAN_CH_0] = { - .conf = &fan_conf_0, - .rpm = &fan_rpm_0, - }, -}; - -/******************************************************************************/ -/* EC thermal management configuration */ - -/* - * Tiger Lake specifies 100 C as maximum TDP temperature. THRMTRIP# occurs at - * 130 C. However, sensor is located next to DDR, so we need to use the lower - * DDR temperature limit (85 C) - */ -const static struct ec_thermal_config thermal_cpu = { - .temp_host = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(70), - [EC_TEMP_THRESH_HALT] = C_TO_K(80), - }, - .temp_host_release = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(65), - }, - .temp_fan_off = C_TO_K(35), - .temp_fan_max = C_TO_K(50), -}; - -/* - * Inductor limits - used for both charger and PP3300 regulator - * - * Need to use the lower of the charger IC, PP3300 regulator, and the inductors - * - * Charger max recommended temperature 100C, max absolute temperature 125C - * PP3300 regulator: operating range -40 C to 145 C - * - * Inductors: limit of 125c - * PCB: limit is 80c - */ -const static struct ec_thermal_config thermal_inductor = { - .temp_host = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(75), - [EC_TEMP_THRESH_HALT] = C_TO_K(80), - }, - .temp_host_release = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(65), - }, - .temp_fan_off = C_TO_K(40), - .temp_fan_max = C_TO_K(55), -}; - - -struct ec_thermal_config thermal_params[] = { - [TEMP_SENSOR_1_CHARGER] = thermal_inductor, - [TEMP_SENSOR_2_PP3300_REGULATOR] = thermal_inductor, - [TEMP_SENSOR_3_DDR_SOC] = thermal_cpu, - [TEMP_SENSOR_4_FAN] = thermal_cpu, -}; -BUILD_ASSERT(ARRAY_SIZE(thermal_params) == TEMP_SENSOR_COUNT); - -/******************************************************************************/ -/* MFT channels. These are logically separate from pwm_channels. */ -const struct mft_t mft_channels[] = { - [MFT_CH_0] = { - .module = NPCX_MFT_MODULE_1, - .clk_src = TCKC_LFCLK, - .pwm_id = PWM_CH_FAN, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(mft_channels) == MFT_CH_COUNT); - -/******************************************************************************/ -/* I2C port map configuration */ -const struct i2c_port_t i2c_ports[] = { - { - .name = "sensor", - .port = I2C_PORT_SENSOR, - .kbps = 400, - .scl = GPIO_EC_I2C0_SENSOR_SCL, - .sda = GPIO_EC_I2C0_SENSOR_SDA, - }, - { - .name = "usb_c0", - .port = I2C_PORT_USB_C0, - .kbps = 1000, - .scl = GPIO_EC_I2C1_USB_C0_SCL, - .sda = GPIO_EC_I2C1_USB_C0_SDA, - }, - { - .name = "usb_c1", - .port = I2C_PORT_USB_C1, - .kbps = 1000, - .scl = GPIO_EC_I2C2_USB_C1_SCL, - .sda = GPIO_EC_I2C2_USB_C1_SDA, - }, - { - .name = "usb_1_mix", - .port = I2C_PORT_USB_1_MIX, - .kbps = 100, - .scl = GPIO_EC_I2C3_USB_1_MIX_SCL, - .sda = GPIO_EC_I2C3_USB_1_MIX_SDA, - }, - { - .name = "power", - .port = I2C_PORT_POWER, - .kbps = 100, - .scl = GPIO_EC_I2C5_BATTERY_SCL, - .sda = GPIO_EC_I2C5_BATTERY_SDA, - }, - { - .name = "eeprom", - .port = I2C_PORT_EEPROM, - .kbps = 400, - .scl = GPIO_EC_I2C7_EEPROM_PWR_SCL_R, - .sda = GPIO_EC_I2C7_EEPROM_PWR_SDA_R, - }, -}; -const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports); - -/******************************************************************************/ -/* PWM configuration */ -const struct pwm_t pwm_channels[] = { - [PWM_CH_LED1_BLUE] = { - .channel = 2, - .flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, - .freq = 4800, - }, - [PWM_CH_LED2_GREEN] = { - .channel = 0, - .flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, - .freq = 4800, - }, - [PWM_CH_LED3_RED] = { - .channel = 1, - .flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, - .freq = 4800, - }, - [PWM_CH_LED4_SIDESEL] = { - .channel = 7, - .flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, - /* - * If using the side select to run both LEDs at the same time, - * the frequency should be 1/2 of the color channel PWM - * frequency to drive each LED equally. - */ - .freq = 2400, - }, - [PWM_CH_FAN] = { - .channel = 5, - .flags = PWM_CONFIG_OPEN_DRAIN, - .freq = 25000 - }, - [PWM_CH_KBLIGHT] = { - .channel = 3, - .flags = 0, - /* - * Set PWM frequency to multiple of 50 Hz and 60 Hz to prevent - * flicker. Higher frequencies consume similar average power to - * lower PWM frequencies, but higher frequencies record a much - * lower maximum power. - */ - .freq = 2400, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT); |