diff options
Diffstat (limited to 'chip/npcx/build.mk')
-rw-r--r-- | chip/npcx/build.mk | 92 |
1 files changed, 0 insertions, 92 deletions
diff --git a/chip/npcx/build.mk b/chip/npcx/build.mk deleted file mode 100644 index 4be1b2994f..0000000000 --- a/chip/npcx/build.mk +++ /dev/null @@ -1,92 +0,0 @@ -# -*- makefile -*- -# Copyright 2014 The Chromium OS Authors. All rights reserved. -# Use of this source code is governed by a BSD-style license that can be -# found in the LICENSE file. -# -# NPCX chip specific files build -# - -# NPCX SoC has a Cortex-M4F ARM core -CORE:=cortex-m -# Allow the full Cortex-M4 instruction set -CFLAGS_CPU+=-march=armv7e-m -mcpu=cortex-m4 - -# Assign default CHIP_FAMILY as npcx5 for old boards used npcx5 series -ifeq ($(CHIP_FAMILY),) -CHIP_FAMILY:=npcx5 -endif - -# Required chip modules -chip-y=header.o clock.o gpio.o hwtimer.o system.o uart.o uartn.o sib.o -chip-y+=system-$(CHIP_FAMILY).o -chip-y+=gpio-$(CHIP_FAMILY).o - -# Optional chip modules -chip-$(CONFIG_ADC)+=adc.o -chip-$(CONFIG_AUDIO_CODEC)+=apm.o wov.o -chip-$(CONFIG_AUDIO_CODEC_DMIC)+=audio_codec_dmic.o -chip-$(CONFIG_AUDIO_CODEC_I2S_RX)+=audio_codec_i2s_rx.o -chip-$(CONFIG_FANS)+=fan.o -chip-$(CONFIG_FLASH_PHYSICAL)+=flash.o -chip-$(CONFIG_I2C)+=i2c.o i2c-$(CHIP_FAMILY).o -chip-$(CONFIG_HOSTCMD_X86)+=lpc.o -chip-$(CONFIG_HOSTCMD_ESPI)+=espi.o -chip-$(CONFIG_PECI)+=peci.o -chip-$(CONFIG_HOSTCMD_SHI)+=shi.o -chip-$(CONFIG_CEC)+=cec.o -# pwm functions are implemented with the fan functions -chip-$(CONFIG_PWM)+=pwm.o -chip-$(CONFIG_SPI)+=spi.o -chip-$(CONFIG_WATCHDOG)+=watchdog.o -ifndef CONFIG_KEYBOARD_NOT_RAW -chip-$(HAS_TASK_KEYSCAN)+=keyboard_raw.o -endif - -chip-$(CONFIG_PS2)+=ps2.o -# Only npcx9 or later chip family can support LCT module -ifneq ($(CHIP_FAMILY),$(filter $(CHIP_FAMILY),npcx5 npcx7)) -chip-y+=lct.o -endif - -chip-$(CONFIG_SHA256_HW_ACCELERATE)+=sha256_chip.o - -# spi monitor program fw for openocd and UUT(UART Update Tool) -npcx-monitor-fw=chip/npcx/spiflashfw/npcx_monitor -npcx-monitor-fw-bin=${out}/$(npcx-monitor-fw).bin -PROJECT_EXTRA+=${npcx-monitor-fw-bin} -# Monitor header is only used for UUT which is not supported on npcx5. -ifneq "$(CHIP_FAMILY)" "npcx5" -npcx-monitor-hdr=chip/npcx/spiflashfw/monitor_hdr -npcx-monitor-hdr-ro-bin=${out}/$(npcx-monitor-hdr)_ro.bin -npcx-monitor-hdr-rw-bin=${out}/$(npcx-monitor-hdr)_rw.bin -PROJECT_EXTRA+=${npcx-monitor-hdr-ro-bin} ${npcx-monitor-hdr-rw-bin} -endif - -# ECST tool is for filling the header used by booter of npcx EC -show_esct_cmd=$(if $(V),,echo ' ECST ' $(subst $(out)/,,$@) ; ) - -# Get the firmware length from the mapfile. This can differ from the file -# size when the CONFIG_CHIP_INIT_ROM_REGION is used. Note that the -fwlen -# parameter for the ecst utility must be in hex. -cmd_fwlen=$(shell awk '\ - /__flash_used =/ {flash_used = strtonum($$1)} \ - END {printf ("%x", flash_used)}' $(1)) - -# ECST options for header -bld_ecst=${out}/util/ecst -chip $(CHIP_VARIANT) \ - -usearmrst -mode bt -ph -i $(1) -o $(2) -nohcrc -nofcrc -flashsize 8 \ - -fwlen $(call cmd_fwlen, $(patsubst %.flat,%.map,$(2))) \ - -spimaxclk 50 -spireadmode dual 1> /dev/null - -# Replace original one with the flat file including header -moveflat=mv -f $(1) $(2) - -# Commands for ECST -cmd_ecst=$(show_esct_cmd)$(call moveflat,$@,$@.tmp);$(call bld_ecst,$@.tmp,$@) - -# Commands to append npcx header in ec.RO.flat -cmd_org_ec_elf_to_flat = $(OBJCOPY) --set-section-flags .roshared=share \ - -O binary $(patsubst %.flat,%.elf,$@) $@ -cmd_npcx_ro_elf_to_flat=$(cmd_org_ec_elf_to_flat);$(cmd_ecst) -cmd_ec_elf_to_flat = $(if $(filter $(out)/RO/ec.RO.flat, $@), \ - $(cmd_npcx_ro_elf_to_flat), $(cmd_org_ec_elf_to_flat) ) |