diff options
Diffstat (limited to 'include/config.h')
-rw-r--r-- | include/config.h | 20 |
1 files changed, 10 insertions, 10 deletions
diff --git a/include/config.h b/include/config.h index a798f0eac1..95258abd54 100644 --- a/include/config.h +++ b/include/config.h @@ -139,7 +139,7 @@ #undef CONFIG_KX022_ORIENTATION_SENSOR /* Define the i2c address of the sensor behind the main sensor, if present. */ -#undef CONFIG_ACCELGYRO_SEC_ADDR +#undef CONFIG_ACCELGYRO_SEC_ADDR__7BF /* * Define if either CONFIG_BMI160_ORIENTATION_SUPPORT or @@ -601,7 +601,7 @@ #undef CONFIG_BOARD_VERSION_GPIO /* EC responses to a board defined I2C slave address */ -#undef CONFIG_BOARD_I2C_SLAVE_ADDR +#undef CONFIG_BOARD_I2C_SLAVE_ADDR__7BF /* * The board is unable to distinguish EC reset from power-on so it should treat @@ -2030,7 +2030,7 @@ * For ECs where the host command interface is I2C, slave * address which the EC will respond to. */ -#undef CONFIG_HOSTCMD_I2C_SLAVE_ADDR +#undef CONFIG_HOSTCMD_I2C_SLAVE_ADDR__7BF /* * Accept EC host commands over the SPI slave (SPS) interface. @@ -2199,7 +2199,7 @@ * transaction is done, the pin is set back to low. */ #undef CONFIG_I2C_SCL_GATE_PORT -#undef CONFIG_I2C_SCL_GATE_ADDR +#undef CONFIG_I2C_SCL_GATE_ADDR__7BF #undef CONFIG_I2C_SCL_GATE_GPIO /* @@ -3411,9 +3411,9 @@ /* Enable Elan driver */ #undef CONFIG_TOUCHPAD_ELAN -/* Set I2C port and address (8-bit) */ +/* Set I2C port and address (7-bit) */ #undef CONFIG_TOUCHPAD_I2C_PORT -#undef CONFIG_TOUCHPAD_I2C_ADDR +#undef CONFIG_TOUCHPAD_I2C_ADDR__7BF /* * Enable touchpad FW update over USB update protocol, and define touchpad @@ -3624,7 +3624,7 @@ #undef CONFIG_USB_PD_IDENTITY_SW_VERS /* USB PD MCU slave address for host commands */ -#define CONFIG_USB_PD_I2C_SLAVE_ADDR 0x3c +#define CONFIG_USB_PD_I2C_SLAVE_ADDR__7BF 0x1E /* Define if using internal comparator for PD receive */ #undef CONFIG_USB_PD_INTERNAL_COMP @@ -3736,7 +3736,7 @@ #undef CONFIG_USB_PD_VBUS_MEASURE_NOT_PRESENT /* Define the type-c port controller I2C base address. */ -#define CONFIG_TCPC_I2C_BASE_ADDR 0x9c +#define CONFIG_TCPC_I2C_BASE_ADDR__7BF 0x4E /* Use this option to enable Try.SRC mode for Dual Role devices */ #undef CONFIG_USB_PD_TRY_SRC @@ -4713,7 +4713,7 @@ #if defined(CONFIG_MAG_BMI160_LIS2MDL) || \ defined(CONFIG_MAG_LSM6DSM_LIS2MDL) #define CONFIG_MAG_LIS2MDL -#ifndef CONFIG_ACCELGYRO_SEC_ADDR +#ifndef CONFIG_ACCELGYRO_SEC_ADDR__7BF #error "The i2c address of the magnetometer is not set." #endif #endif @@ -4722,7 +4722,7 @@ #if defined(CONFIG_MAG_BMI160_BMM150) || \ defined(CONFIG_MAG_LSM6DSM_BMM150) #define CONFIG_MAG_BMM150 -#ifndef CONFIG_ACCELGYRO_SEC_ADDR +#ifndef CONFIG_ACCELGYRO_SEC_ADDR__7BF #error "The i2c address of the magnetometer is not set." #endif #endif |