diff options
Diffstat (limited to 'zephyr/Kconfig.motionsense')
-rw-r--r-- | zephyr/Kconfig.motionsense | 190 |
1 files changed, 0 insertions, 190 deletions
diff --git a/zephyr/Kconfig.motionsense b/zephyr/Kconfig.motionsense deleted file mode 100644 index daf2bbcdf8..0000000000 --- a/zephyr/Kconfig.motionsense +++ /dev/null @@ -1,190 +0,0 @@ -# Copyright 2021 The Chromium OS Authors. All rights reserved. -# Use of this source code is governed by a BSD-style license that can be -# found in the LICENSE file. - -menuconfig PLATFORM_EC_MOTIONSENSE - bool "Motion Sense" - select HAS_TASK_MOTIONSENSE - help - Enable motion sense task. The task collects data from available sensors - and report them to AP. Besides the task reports the sensor data to AP. - Based on the data, it also does other things like calculating lid angle - and detect tablet mode. - -config PLATFORM_EC_ACCEL_FIFO - bool "Sensor FIFO" - help - Enable this to add the sensor FIFO used by sensor device drivers to fill. - Using FIFO reduces power consumption since it reduces the number of - AP wake-ups. - -if PLATFORM_EC_ACCEL_FIFO - -config PLATFORM_EC_ACCEL_FIFO_SIZE - int "Motion Sense FIFO Size" - default 256 - help - This sets the size of the sensor FIFO, must be a power of 2. - -config PLATFORM_EC_ACCEL_FIFO_THRES - int "FIFO Threshold" - default 85 # (PLATFORM_EC_ACCEL_FIFO_SIZE / 3) - help - This sets the amount of free entries that trigger an interrupt to the AP. - -endif # PLATFORM_EC_ACCEL_FIFO - -config PLATFORM_EC_SENSOR_TIGHT_TIMESTAMPS - bool "Extra Sensor Timestamp" - help - If this is defined, motion_sense sends - sensor events to the AP in the format - +-----------+ - | Timestamp | - | Payload | - | Timestamp | - | Payload | - | ... | - +-----------+ - If this is not defined, the events will be sent in the format - +-----------+ - | Payload | - | Payload | - | Payload | - | ... | - | Timestamp | - +-----------+ - The former format enables improved filtering of sensor event - timestamps on the AP, but comes with stricter jitter requirements. - -config PLATFORM_EC_ACCEL_INTERRUPTS - bool "Accelerometer Interrupts" - help - Enable this to allow a sensor driver to send an event to motion task when - the sensor gets the data ready interrupt. On the event, motion task calls - the driver's irq_handler to collect data. - -# TODO(b/173507858) config PLATFORM_EC_MOTION_FILL_LPC_SENSE_DATA -# if PLATFORM_EC_MOTION_FILL_LPC_SENSE_DATA -#endif # PLATFORM_EC_MOTION_FILL_LPC_SENSE_DATA - -config PLATFORM_EC_ALS - bool "Ambient Light Sensor(ALS)" - default y if HAS_TASK_ALS - help - Enable this to indicate there's at least one or more ALS devices available. - If PLATFORM_EC_MOTION_FILL_LPC_SENSE_DATA is set, then motion task updates - the designated part of EC memmap with the ALS data. The updating EC memmap - can be also done by the dedicated ALS task with HAS_ALS_TASK set. - Number of ALS entries reserved in EC memmap are defined by EC_ALS_ENTRIES - in ec_commands.h. - -if PLATFORM_EC_ALS - -config PLATFORM_EC_ALS_COUNT - int "Number of ALS devices" - default 1 - help - This sets the number of ALS devices. This should be less than or equal to - EC_ALS_ENTRIES in ec_commands.h - TODO(b/173507858) move this to device tree - -endif # PLATFORM_EC_ALS - -config PLATFORM_EC_DYNAMIC_MOTION_SENSOR_COUNT - bool "Dynamic Motion Sensor Count" - help - Enable this to allow changing motion sensor count dynamically. - -config PLATFORM_EC_LID_ANGLE - bool "Lid Angle" - help - Enable this to detect lid angle with two accelerometers. The andgle - calculation requires the information about which sensor is on the lid - and which one is on the base. The measured lid angle can be used for - tablet mode detection(refer "Tablet Mode below") and enabling/disabling - peripheral devices(refer "Lid Angle Update" below). - # TODO(b/173507858): add more detail after .dts change - -if PLATFORM_EC_LID_ANGLE - -config PLATFORM_EC_LID_ANGLE_UPDATE - bool "Lid Angle Update" - help - Enable this to allow using the lid angle measurement to determine if - peripheral devices should be enabled or disabled, like key scanning, - trackpad interrupt. - -config PLATFORM_EC_TABLET_MODE - bool "Tablet Mode" - help - Enable this for a device which can be a tablet as well as a clamshell. - Tablet mode detection is done either by using the lid angle measurement - or by the dedicated GMR sensor. - -if PLATFORM_EC_TABLET_MODE - -config PLATFORM_EC_TABLET_MODE_SWITCH - bool "Tablet Mode Switch" - depends on PLATFORM_EC_MKBP_INPUT_DEVICES - help - Enable a virtual switch to indicate when we are in tablet mode. The tablet - mode state is sent to AP via MKBP protocol(switch event). - -config PLATFORM_EC_GMR_TABLET_MODE - bool "Giant Magnetoresistance(GMR) Tablet Mode" - help - Enable this to use GMR sensor to detect tablet mode. - It requires to set GMR_TABLET_MODE_GPIO_L to map the interrupt from - the sensor and direct its mapping to gmr_tablet_switch_isr - in common/tablet_mode.c. - -endif # PLATFORM_EC_TABLET_MODE -endif # PLATFORM_EC_LID_ANGLE - -config PLATFORM_EC_CONSOLE_CMD_ACCELS - bool "Console commands: accels, accelrate, accelinit, accelinfo, etc." - help - Enables console commands: - - accelrange <sensor id> <data> <roundup> - Read or write accelerometer - range - accelres <sensor id> <data> <roundup> - Read or write accelerometer - resolution - accelrate <sensor id> <data> <roundup> - Read or write accelerometer - ODR - accelread <sensor id> [n(iteration)] - Read sensor x/y/z - accelinit <sensor id> - Init sensor - -if PLATFORM_EC_CONSOLE_CMD_ACCELS - -config PLATFORM_EC_CONSOLE_CMD_ACCEL_INFO - bool "Console Command: accelinfo" - help - Enable console command: - - accelinfo on/off [interval] - Print motion sensor info, lid angle - calculations and set calculation frequency. - -endif # PLATFORM_EC_CONSOLE_CMD_ACCELS - -config PLATFORM_EC_ACCEL_SPOOF_MODE - bool "Sensor spoof mode" - help - Enable this to allow sensors values spoofed to any arbitrary value. - This is useful for testing the motion sense framework if the hardware - sensor or the sensor driver code is not ready. - -if PLATFORM_EC_ACCEL_SPOOF_MODE - -config PLATFORM_EC_CONSOLE_CMD_ACCEL_SPOOF - bool "Console Command: accelspoof" - help - Enable console command: - - accelspoof id [on/off] [X] [Y] [Z] - Enable/Disable spoofing of - sensor readings. - -endif # PLATFORM_EC_ACCEL_SPOOF_MODE - -rsource "Kconfig.sensor_devices" |