1 files changed, 0 insertions, 77 deletions
diff --git a/zephyr/include/emul/emul_sm5803.h b/zephyr/include/emul/emul_sm5803.h
deleted file mode 100644
index 006fe1d0c7..0000000000
--- a/zephyr/include/emul/emul_sm5803.h
+++ /dev/null
@@ -1,77 +0,0 @@
-/* Copyright 2023 The ChromiumOS Authors
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-#include <zephyr/drivers/emul.h>
-#include <zephyr/drivers/gpio.h>
-
-const struct gpio_dt_spec *
-sm5803_emul_get_interrupt_gpio(const struct emul *emul);
-struct i2c_common_emul_data *sm5803_emul_get_i2c_main(const struct emul *emul);
-struct i2c_common_emul_data *sm5803_emul_get_i2c_chg(const struct emul *emul);
-struct i2c_common_emul_data *sm5803_emul_get_i2c_meas(const struct emul *emul);
-struct i2c_common_emul_data *sm5803_emul_get_i2c_test(const struct emul *emul);
-
-/**
- * Read the value of a charger page register, by address.
- *
- * This is useful to verify that a user has written an expected value to a
- * register, without depending on the user's corresponding getter function.
- *
- * @return negative value on error, otherwise 8-bit register value.
- */
-int sm5803_emul_read_chg_reg(const struct emul *emul, uint8_t reg);
-
-/**
- * Set the reported VBUS voltage, in mV.
- *
- * If the VBUS voltage crosses the charger detection threshold as a result,
- * a CHG_DET interrupt will automatically be triggered.
- */
-void sm5803_emul_set_vbus_voltage(const struct emul *emul, uint16_t mv);
-
-/** Set the reported input current (from VBUS), in mA. */
-void sm5803_emul_set_input_current(const struct emul *emul, uint16_t mv);
-
-/** Set the reported battery charge current, in mA. */
-void sm5803_emul_set_battery_current(const struct emul *emul, uint16_t ma);
-
-/** Set the reported device ID (default 3). */
-void sm5803_emul_set_device_id(const struct emul *emul, uint8_t id);
-
-/** Set the platform ID as configured in hardware by the PMODE resistor. */
-void sm5803_emul_set_pmode(const struct emul *emul, uint8_t pmode);
-
-/** Get the register value of ICHG_FAST_SET; the fast charge current limit. */
-int sm5803_emul_get_fast_charge_current_limit(const struct emul *emul);
-
-/** Get the values of the GPADC_CONFIG_1 and GPADC_CONFIG_2 registers. */
-void sm5803_emul_get_gpadc_conf(const struct emul *emul, uint8_t *conf1,
-				uint8_t *conf2);
-
-/** Set the GPADC enable bits in GPADC_CONFIG_1 and GPADC_CONFIG_2 registers. */
-void sm5803_emul_set_gpadc_conf(const struct emul *emul, uint8_t conf1,
-				uint8_t conf2);
-
-/** Return whether the main clock is slowed (CLOCK_SEL:LOW_POWER_CLOCK_EN). */
-bool sm5803_emul_is_clock_slowed(const struct emul *emul);
-
-/** Get the value of the CC_CONFIG_1 register. */
-uint8_t sm5803_emul_get_cc_config(const struct emul *emul);
-
-/** Get the values of the FLOW1..FLOW3 registers. */
-void sm5803_emul_get_flow_regs(const struct emul *emul, uint8_t *flow1,
-			       uint8_t *flow2, uint8_t *flow3);
-
-/**
- * Set the INT_REQ_* registers to indicate pending interrupts.
- *
- * This does not clear pending IRQs; it only asserts them. IRQs are cleared only
- * when the interrupt status registers are read.
- */
-void sm5803_emul_set_irqs(const struct emul *emul, uint8_t irq1, uint8_t irq2,
-			  uint8_t irq3, uint8_t irq4);
-
-/** Get the value of the GPIO_CTRL_1 register, which controls GPIO0. */
-uint8_t sm5803_emul_get_gpio_ctrl(const struct emul *emul);