diff options
Diffstat (limited to 'zephyr/program/nissa/pujjo/overlay.dtsi')
-rw-r--r-- | zephyr/program/nissa/pujjo/overlay.dtsi | 371 |
1 files changed, 0 insertions, 371 deletions
diff --git a/zephyr/program/nissa/pujjo/overlay.dtsi b/zephyr/program/nissa/pujjo/overlay.dtsi deleted file mode 100644 index cb20ec6554..0000000000 --- a/zephyr/program/nissa/pujjo/overlay.dtsi +++ /dev/null @@ -1,371 +0,0 @@ -/* Copyright 2022 The ChromiumOS Authors - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include <cros/thermistor/thermistor.dtsi> -#include <dt-bindings/usb_pd_tcpm.h> - -/ { - aliases { - gpio-cbi-wp = &gpio_ec_cbi_wp; - gpio-wp = &gpio_ec_wp_odl; - int-wp = &int_wp_l; - gpio-kbd-kso2 = &gpio_ec_kso_02_inv; - }; - - ec-console { - compatible = "ec-console"; - disabled = "events", "lpc", "hostcmd"; - }; - - batteries { - default_battery: smp { - compatible = "smp,l22m3pg0", "battery-smart"; - }; - smp_l22m3pg1 { - compatible = "smp,l22m3pg1", "battery-smart"; - }; - sunwoda_l22d3pg0 { - compatible = "sunwoda,l22d3pg0", "battery-smart"; - }; - sunwoda_l22d3pg1 { - compatible = "sunwoda,l22d3pg1", "battery-smart"; - }; - celxpert_l22c3pg0 { - compatible = "celxpert,l22c3pg0", "battery-smart"; - }; - }; - - hibernate-wake-pins { - compatible = "cros-ec,hibernate-wake-pins"; - wakeup-irqs = < - &int_power_button - &int_lid_open - >; - }; - - gpio-interrupts { - compatible = "cros-ec,gpio-interrupts"; - - int_power_button: power_button { - irq-pin = <&gpio_gsc_ec_pwr_btn_odl>; - flags = <GPIO_INT_EDGE_BOTH>; - handler = "power_button_interrupt"; - }; - int_wp_l: wp_l { - irq-pin = <&gpio_ec_wp_odl>; - flags = <GPIO_INT_EDGE_BOTH>; - handler = "switch_interrupt"; - }; - int_lid_open: lid_open { - irq-pin = <&gpio_lid_open>; - flags = <GPIO_INT_EDGE_BOTH>; - handler = "lid_interrupt"; - }; - int_tablet_mode: tablet_mode { - irq-pin = <&gpio_tablet_mode_l>; - flags = <GPIO_INT_EDGE_BOTH>; - handler = "gmr_tablet_switch_isr"; - }; - int_imu: ec_imu { - irq-pin = <&gpio_imu_int_l>; - flags = <GPIO_INT_EDGE_FALLING>; - handler = "motion_interrupt"; - }; - int_lid_accel: lid_accel { - irq-pin = <&gpio_acc_int_l>; - flags = <GPIO_INT_EDGE_FALLING>; - handler = "lid_accel_interrupt"; - }; - int_vol_down: vol_down { - irq-pin = <&gpio_voldn_btn_odl>; - flags = <GPIO_INT_EDGE_BOTH>; - handler = "button_interrupt"; - }; - int_vol_up: vol_up { - irq-pin = <&gpio_volup_btn_odl>; - flags = <GPIO_INT_EDGE_BOTH>; - handler = "button_interrupt"; - }; - int_usb_c0: usb_c0 { - irq-pin = <&gpio_usb_c0_int_odl>; - flags = <GPIO_INT_EDGE_FALLING>; - handler = "usb_interrupt"; - }; - }; - - named-gpios { - gpio_sb_2: sb_2 { - gpios = <&gpiod 4 GPIO_OUTPUT>; - no-auto-init; - }; - - gpio_sb_3: sb_3 { - gpios = <&gpiof 5 (GPIO_OPEN_DRAIN | GPIO_VOLTAGE_1P8)>; - no-auto-init; - }; - gpio_sb_4: sb_4 { - gpios = <&gpiof 4 (GPIO_INPUT | GPIO_VOLTAGE_1P8)>; - no-auto-init; - }; - gpio_fan_enable: fan-enable { - gpios = <&gpio6 3 GPIO_OUTPUT>; - no-auto-init; - }; - ec-i2c-sensor-scl { - gpios = <&gpio9 0 (GPIO_INPUT | GPIO_VOLTAGE_1P8)>; - }; - ec-i2c-sensor-sda { - gpios = <&gpio8 7 (GPIO_INPUT | GPIO_VOLTAGE_1P8)>; - }; - gpio_power_led: power_led { - gpios = <&gpioc 2 GPIO_OUTPUT_LOW>; - }; - gpio_led_1_odl: led_1_odl { - gpios = <&gpioc 4 GPIO_OUTPUT_LOW>; - }; - gpio_led_2_odl: led_2_odl { - gpios = <&gpioc 3 GPIO_OUTPUT_LOW>; - }; - }; - - /* - * Aliases used for sub-board GPIOs. - */ - aliases { - /* - * Sub-board with type A USB, enable. - */ - gpio-en-usb-a1-vbus = &gpio_sb_2; - /* - * HPD pins for HDMI sub-board. - */ - gpio-hdmi-en-odl = &gpio_sb_3; - gpio-hpd-odl = &gpio_sb_4; - /* - * Enable S5 rails for LTE sub-board - */ - gpio-en-sub-s5-rails = &gpio_sb_2; - }; - - temp_cpu: cpu { - compatible = "cros-ec,temp-sensor-thermistor"; - thermistor = <&thermistor_3V3_51K1_47K_4050B>; - adc = <&adc_temp_sensor_1>; - }; - temp_ddr: ddr { - compatible = "cros-ec,temp-sensor-thermistor"; - thermistor = <&thermistor_3V3_51K1_47K_4050B>; - adc = <&adc_temp_sensor_2>; - }; - temp_ambient: ambient { - compatible = "cros-ec,temp-sensor-thermistor"; - thermistor = <&thermistor_3V3_51K1_47K_4050B>; - adc = <&adc_temp_sensor_3>; - }; - - named-temp-sensors { - compatible = "cros-ec,temp-sensors"; - cpu { - temp_fan_off = <35>; - temp_fan_max = <60>; - temp_host_high = <90>; - temp_host_halt = <100>; - temp_host_release_high = <85>; - power-good-pin = <&gpio_ec_soc_dsw_pwrok>; - sensor = <&temp_cpu>; - }; - ddr { - temp_fan_off = <35>; - temp_fan_max = <60>; - temp_host_high = <90>; - temp_host_halt = <100>; - temp_host_release_high = <85>; - power-good-pin = <&gpio_ec_soc_dsw_pwrok>; - sensor = <&temp_ddr>; - }; - ambient { - temp_fan_off = <35>; - temp_fan_max = <60>; - temp_host_high = <90>; - temp_host_halt = <100>; - temp_host_release_high = <85>; - power-good-pin = <&gpio_ec_soc_dsw_pwrok>; - sensor = <&temp_ambient>; - }; - }; - - usba { - compatible = "cros-ec,usba-port-enable-pins"; - /* - * sb_2 is only configured as GPIO when USB-A1 is present, - * but it's still safe to control when disabled. - * - * ILIM_SEL pins are referred to by legacy enum name, - * GPIO_USB*_ILIM_SEL. The one for port A1 is unused on - * sub-boards that don't have USB-A so is safe to control - * regardless of system configuration. - */ - enable-pins = <&gpio_en_usb_a0_vbus &gpio_sb_2>; - status = "okay"; - }; - - usbc { - #address-cells = <1>; - #size-cells = <0>; - - port0@0 { - compatible = "named-usbc-port"; - reg = <0>; - bc12 = <&bc12_port0>; - chg = <&chg_port0>; - tcpc = <&tcpc_port0>; - usb-mux-chain-0 { - compatible = "cros-ec,usb-mux-chain"; - usb-muxes = <&virtual_mux_0>; - }; - }; - port0-muxes { - virtual_mux_0: virtual-mux-0 { - compatible = "cros-ec,usbc-mux-virtual"; - }; - }; - }; - - fans { - compatible = "cros-ec,fans"; - - fan_0 { - pwms = <&pwm5 5 PWM_KHZ(1) PWM_POLARITY_NORMAL>; - rpm_min = <2200>; - rpm_start = <2200>; - rpm_max = <4200>; - tach = <&tach2>; - enable_gpio = <&gpio_fan_enable>; - }; - }; - - /* - * Declare unused GPIOs so that they are shut down - * and use minimal power - */ - unused-pins { - compatible = "unused-gpios"; - unused-gpios = - <&gpio3 3 0>, - <&gpio3 6 0>, - <&gpiod 7 0>, - <&gpiof 2 0>, - <&gpiof 3 0>; - }; -}; - -&thermistor_3V3_51K1_47K_4050B { - status = "okay"; -}; - -&adc_ec_vsense_pp3300_s5 { - /* - * Voltage divider on input has 47k upper and 220k lower legs with - * 2714 mV full-scale reading on the ADC. Apply the largest possible - * multiplier (without overflowing int32) to get the best possible - * approximation of the actual ratio, but derate by a factor of two to - * ensure unexpectedly high values won't overflow. - */ - mul = <(791261 / 2)>; - div = <(651975 / 2)>; -}; - -/* Set bus speeds for I2C */ -&i2c0_0 { - label = "I2C_EEPROM"; - clock-frequency = <I2C_BITRATE_FAST>; - - cbi_eeprom: eeprom@50 { - compatible = "atmel,at24"; - reg = <0x50>; - size = <2048>; - pagesize = <16>; - address-width = <8>; - timeout = <5>; - }; -}; - -&i2c1_0 { - label = "I2C_SENSOR"; - clock-frequency = <I2C_BITRATE_FAST>; -}; - -&i2c3_0 { - label = "I2C_USB_C0_TCPC"; - clock-frequency = <I2C_BITRATE_FAST_PLUS>; - - bc12_port0: pi3usb9201@5f { - compatible = "pericom,pi3usb9201"; - status = "okay"; - reg = <0x5f>; - /* - * BC1.2 interrupt is shared with TCPC, so - * IRQ is not specified here and handled by - * usb_c0_interrupt. - */ - }; - - chg_port0: isl923x@9 { - compatible = "intersil,isl923x"; - status = "okay"; - reg = <0x9>; - }; - - tcpc_port0: raa489000@22 { - compatible = "renesas,raa489000"; - reg = <0x22>; - tcpc-flags = <( - TCPC_FLAGS_TCPCI_REV2_0 | - TCPC_FLAGS_VBUS_MONITOR)>; - }; -}; - -&i2c7_0 { - label = "I2C_BATTERY"; - clock-frequency = <I2C_BITRATE_STANDARD>; -}; - -&pwm5_gpb7 { - drive-open-drain; -}; - -&pwm5 { - status = "okay"; - clock-bus = "NPCX_CLOCK_BUS_LFCLK"; - pinctrl-0 = <&pwm5_gpb7>; - pinctrl-names = "default"; -}; - -/* Tachometer for fan speed measurement */ -&tach2 { - status = "okay"; - pinctrl-0 = <&ta2_1_in_gp73>; - pinctrl-names = "default"; - port = <NPCX_TACH_PORT_A>; /* port-A is selected */ - sample-clk = <NPCX_TACH_FREQ_LFCLK>; /* Use LFCLK as sampling clock */ - pulses-per-round = <2>; /* number of pulses per round of encoder */ -}; - -/* host interface */ -&espi0 { - status = "okay"; - pinctrl-0 = <&espi_lpc_gp46_47_51_52_53_54_55_57>; - pinctrl-names = "default"; -}; - -/* - * Declare GPIOs that have leakage current caused by board issues here. NPCX ec - * will disable their input buffers before entering deep sleep and restore them - * after waking up automatically for better power consumption. - */ -&power_leakage_io { - leak-gpios = <&gpioa 4 0 - &gpiof 1 0>; -}; |