diff options
Diffstat (limited to 'zephyr/program/nissa/src/sub_board.c')
-rw-r--r-- | zephyr/program/nissa/src/sub_board.c | 288 |
1 files changed, 288 insertions, 0 deletions
diff --git a/zephyr/program/nissa/src/sub_board.c b/zephyr/program/nissa/src/sub_board.c new file mode 100644 index 0000000000..e8e9648ba6 --- /dev/null +++ b/zephyr/program/nissa/src/sub_board.c @@ -0,0 +1,288 @@ +/* Copyright 2022 The ChromiumOS Authors + * Use of this source code is governed by a BSD-style license that can be + * found in the LICENSE file. + */ + +/* Nissa sub-board hardware configuration */ + +#include "cros_board_info.h" +#include "driver/tcpm/tcpci.h" +#include "gpio/gpio_int.h" +#include "hooks.h" +#include "nissa_common.h" +#include "nissa_hdmi.h" +#include "task.h" +#include "usb_charge.h" +#include "usb_pd.h" +#include "usbc/usb_muxes.h" + +#include <zephyr/drivers/gpio.h> +#include <zephyr/drivers/pinctrl.h> +#include <zephyr/init.h> +#include <zephyr/kernel.h> +#include <zephyr/sys/printk.h> + +#include <ap_power/ap_power.h> + +LOG_MODULE_DECLARE(nissa, CONFIG_NISSA_LOG_LEVEL); + +#if NISSA_BOARD_HAS_HDMI_SUPPORT +static void hdmi_power_handler(struct ap_power_ev_callback *cb, + struct ap_power_ev_data data) +{ + /* Enable VCC on the HDMI port. */ + const struct gpio_dt_spec *s3_rail = + GPIO_DT_FROM_ALIAS(gpio_hdmi_en_odl); + /* Connect AP's DDC to sub-board (default is USB-C aux) */ + const struct gpio_dt_spec *ddc_select = + GPIO_DT_FROM_NODELABEL(gpio_hdmi_sel); + + switch (data.event) { + case AP_POWER_PRE_INIT: + LOG_DBG("Connecting HDMI DDC to sub-board"); + gpio_pin_set_dt(ddc_select, 1); + break; + case AP_POWER_STARTUP: + LOG_DBG("Enabling HDMI VCC"); + gpio_pin_set_dt(s3_rail, 1); + break; + case AP_POWER_SHUTDOWN: + LOG_DBG("Disabling HDMI VCC"); + gpio_pin_set_dt(s3_rail, 0); + break; + case AP_POWER_HARD_OFF: + LOG_DBG("Disconnecting HDMI sub-board DDC"); + gpio_pin_set_dt(ddc_select, 0); + break; + default: + LOG_ERR("Unhandled HDMI power event %d", data.event); + break; + } +} + +static void hdmi_hpd_interrupt(const struct device *device, + struct gpio_callback *callback, + gpio_port_pins_t pins) +{ + int state = gpio_pin_get_dt(GPIO_DT_FROM_ALIAS(gpio_hpd_odl)); + + gpio_pin_set_dt(GPIO_DT_FROM_NODELABEL(gpio_ec_soc_hdmi_hpd), state); + LOG_DBG("HDMI HPD changed state to %d", state); +} + +void nissa_configure_hdmi_rails(void) +{ +#if DT_NODE_EXISTS(GPIO_DT_FROM_ALIAS(gpio_en_rails_odl)) + gpio_pin_configure_dt(GPIO_DT_FROM_ALIAS(gpio_en_rails_odl), + GPIO_OUTPUT_INACTIVE | GPIO_OPEN_DRAIN | + GPIO_PULL_UP | GPIO_ACTIVE_LOW); +#endif +} + +void nissa_configure_hdmi_vcc(void) +{ + gpio_pin_configure_dt(GPIO_DT_FROM_ALIAS(gpio_hdmi_en_odl), + GPIO_OUTPUT_INACTIVE | GPIO_OPEN_DRAIN | + GPIO_ACTIVE_LOW); +} + +__overridable void nissa_configure_hdmi_power_gpios(void) +{ + nissa_configure_hdmi_rails(); +} + +#ifdef CONFIG_SOC_IT8XXX2 +/* + * On it8xxx2, the below condition will break the EC to enter deep doze mode + * (b:237717730): + * Enhance i2c (GPE0/E7, GPH1/GPH2 or GPA4/GPA5) is enabled and its clock and + * data pins aren't both at high level. + * + * Since HDMI+type A SKU doesn't use i2c4, disable it for better power number. + */ +#define I2C4_NODE DT_NODELABEL(i2c4) +#if DT_NODE_EXISTS(I2C4_NODE) +PINCTRL_DT_DEFINE(I2C4_NODE); + +/* disable i2c4 alternate function */ +static void soc_it8xxx2_disable_i2c4_alt(void) +{ + const struct pinctrl_dev_config *pcfg = + PINCTRL_DT_DEV_CONFIG_GET(I2C4_NODE); + + pinctrl_apply_state(pcfg, PINCTRL_STATE_SLEEP); +} +#endif /* DT_NODE_EXISTS(I2C4_NODE) */ +#endif /* CONFIG_SOC_IT8XXX2 */ +#endif /* NISSA_BOARD_HAS_HDMI_SUPPORT */ + +static void lte_power_handler(struct ap_power_ev_callback *cb, + struct ap_power_ev_data data) +{ + /* Enable rails for S5 */ + const struct gpio_dt_spec *s5_rail = + GPIO_DT_FROM_ALIAS(gpio_en_sub_s5_rails); + switch (data.event) { + case AP_POWER_PRE_INIT: + LOG_DBG("Enabling LTE sub-board power rails"); + gpio_pin_set_dt(s5_rail, 1); + break; + case AP_POWER_HARD_OFF: + LOG_DBG("Disabling LTE sub-board power rails"); + gpio_pin_set_dt(s5_rail, 0); + break; + default: + LOG_ERR("Unhandled LTE power event %d", data.event); + break; + } +} + +/** + * Configure GPIOs (and other pin functions) that vary with present sub-board. + * + * The functions of some pins vary according to which sub-board is present + * (indicated by CBI fw_config); this function configures them according to the + * needs of the present sub-board. + */ +static void nereid_subboard_config(void) +{ + enum nissa_sub_board_type sb = nissa_get_sb_type(); + static struct ap_power_ev_callback power_cb; + + /* + * USB-A port: current limit output is configured by default and unused + * if this port is not present. VBUS enable must be configured if + * needed and is controlled by the usba-port-enable-pins driver. + */ + if (sb == NISSA_SB_C_A || sb == NISSA_SB_HDMI_A || + sb == NISSA_SB_NONE) { + /* + * Configure VBUS enable, retaining current value. + * SB_NONE indicates missing fw_config; it's safe to enable VBUS + * control in this case since all that will happen is we turn + * off power to LTE, and it's useful to allow USB-A to work in + * such a configuration. + */ + gpio_pin_configure_dt(GPIO_DT_FROM_ALIAS(gpio_en_usb_a1_vbus), + GPIO_OUTPUT); + } else { + /* Turn off unused pins */ + gpio_pin_configure_dt( + GPIO_DT_FROM_NODELABEL(gpio_sub_usb_a1_ilimit_sdp), + GPIO_DISCONNECTED); + gpio_pin_configure_dt(GPIO_DT_FROM_ALIAS(gpio_en_usb_a1_vbus), + GPIO_DISCONNECTED); + /* Disable second USB-A port enable GPIO */ + __ASSERT(USB_PORT_ENABLE_COUNT == 2, + "USB A port count != 2 (%d)", USB_PORT_ENABLE_COUNT); + usb_port_enable[1] = -1; + } + /* + * USB-C port: the default configuration has I2C on the I2C pins, + * but the interrupt line needs to be configured. + */ +#if CONFIG_USB_PD_PORT_MAX_COUNT > 1 + if (sb == NISSA_SB_C_A || sb == NISSA_SB_C_LTE) { + /* Configure interrupt input */ + gpio_pin_configure_dt(GPIO_DT_FROM_ALIAS(gpio_usb_c1_int_odl), + GPIO_INPUT | GPIO_PULL_UP); + } else { + /* Port doesn't exist, doesn't need muxing */ + USB_MUX_ENABLE_ALTERNATIVE(usb_mux_chain_1_no_mux); + } +#endif + + switch (sb) { +#if NISSA_BOARD_HAS_HDMI_SUPPORT + case NISSA_SB_HDMI_A: { + /* + * HDMI: two outputs control power which must be configured to + * non-default settings, and HPD must be forwarded to the AP + * on another output pin. + */ + const struct gpio_dt_spec *hpd_gpio = + GPIO_DT_FROM_ALIAS(gpio_hpd_odl); + static struct gpio_callback hdmi_hpd_cb; + int rv, irq_key; + + nissa_configure_hdmi_power_gpios(); + +#if CONFIG_SOC_IT8XXX2 && DT_NODE_EXISTS(I2C4_NODE) + /* disable i2c4 alternate function for better power number */ + soc_it8xxx2_disable_i2c4_alt(); +#endif + + /* + * Control HDMI power according to AP power state. Some events + * won't do anything if the corresponding pin isn't configured, + * but that's okay. + */ + ap_power_ev_init_callback( + &power_cb, hdmi_power_handler, + AP_POWER_PRE_INIT | AP_POWER_HARD_OFF | + AP_POWER_STARTUP | AP_POWER_SHUTDOWN); + ap_power_ev_add_callback(&power_cb); + + /* + * Configure HPD input from sub-board; it's inverted by a buffer + * on the sub-board. + */ + gpio_pin_configure_dt(hpd_gpio, GPIO_INPUT | GPIO_ACTIVE_LOW); + /* Register interrupt handler for HPD changes */ + gpio_init_callback(&hdmi_hpd_cb, hdmi_hpd_interrupt, + BIT(hpd_gpio->pin)); + gpio_add_callback(hpd_gpio->port, &hdmi_hpd_cb); + rv = gpio_pin_interrupt_configure_dt(hpd_gpio, + GPIO_INT_EDGE_BOTH); + __ASSERT(rv == 0, + "HPD interrupt configuration returned error %d", rv); + /* + * Run the HPD handler once to ensure output is in sync. + * Lock interrupts to ensure that we don't cause desync if an + * HPD interrupt comes in between the internal read of the input + * and write to the output. + */ + irq_key = irq_lock(); + hdmi_hpd_interrupt(hpd_gpio->port, &hdmi_hpd_cb, + BIT(hpd_gpio->pin)); + irq_unlock(irq_key); + break; + } +#endif + case NISSA_SB_C_LTE: + /* + * LTE: Set up callbacks for enabling/disabling + * sub-board power on S5 state. + */ + gpio_pin_configure_dt(GPIO_DT_FROM_ALIAS(gpio_en_sub_s5_rails), + GPIO_OUTPUT_INACTIVE); + /* Control LTE power when CPU entering or + * exiting S5 state. + */ + ap_power_ev_init_callback(&power_cb, lte_power_handler, + AP_POWER_HARD_OFF | + AP_POWER_PRE_INIT); + ap_power_ev_add_callback(&power_cb); + break; + + default: + break; + } +} +DECLARE_HOOK(HOOK_INIT, nereid_subboard_config, HOOK_PRIO_POST_FIRST); + +/* + * Enable interrupts + */ +static void board_init(void) +{ + /* + * Enable USB-C interrupts. + */ + gpio_enable_dt_interrupt(GPIO_INT_FROM_NODELABEL(int_usb_c0)); +#if CONFIG_USB_PD_PORT_MAX_COUNT > 1 + if (board_get_usb_pd_port_count() == 2) + gpio_enable_dt_interrupt(GPIO_INT_FROM_NODELABEL(int_usb_c1)); +#endif +} +DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT); |