diff options
Diffstat (limited to 'zephyr/projects/nissa/nereid/overlay.dtsi')
-rw-r--r-- | zephyr/projects/nissa/nereid/overlay.dtsi | 400 |
1 files changed, 0 insertions, 400 deletions
diff --git a/zephyr/projects/nissa/nereid/overlay.dtsi b/zephyr/projects/nissa/nereid/overlay.dtsi deleted file mode 100644 index a44a3e01bd..0000000000 --- a/zephyr/projects/nissa/nereid/overlay.dtsi +++ /dev/null @@ -1,400 +0,0 @@ -/* Copyright 2021 The ChromiumOS Authors - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include <cros/thermistor/thermistor.dtsi> - -/ { - aliases { - gpio-cbi-wp = &gpio_ec_cbi_wp; - gpio-wp = &gpio_ec_wp_odl; - int-wp = &int_wp_l; - /* - * USB-C: interrupt input. - * I2C pins are on i2c_ec_i2c_sub_usb_c1 - */ - gpio-usb-c1-int-odl = &gpio_sb_1; - /* - * USB-A: VBUS enable output - * LTE: power enable output - */ - gpio-en-usb-a1-vbus = &gpio_sb_2; - /* - * HDMI: power enable output, HDMI enable output, - * and HPD input - */ - gpio-en-rails-odl = &gpio_sb_1; - gpio-hdmi-en-odl = &gpio_sb_4; - gpio-hpd-odl = &gpio_sb_3; - /* - * Enable S5 rails for LTE sub-board - */ - gpio-en-sub-s5-rails = &gpio_sb_2; - }; - - - ec-console { - compatible = "ec-console"; - disabled = "events", "lpc", "hostcmd"; - }; - - batteries { - default_battery: smp { - compatible = "smp,l20m3pg0", "battery-smart"; - }; - }; - - hibernate-wake-pins { - compatible = "cros-ec,hibernate-wake-pins"; - wakeup-irqs = < - &int_power_button - &int_lid_open - >; - }; - - gpio-interrupts { - compatible = "cros-ec,gpio-interrupts"; - - int_power_button: power_button { - irq-pin = <&gpio_gsc_ec_pwr_btn_odl>; - flags = <GPIO_INT_EDGE_BOTH>; - handler = "power_button_interrupt"; - }; - int_vol_down: vol_down { - irq-pin = <&gpio_voldn_btn_odl>; - flags = <GPIO_INT_EDGE_BOTH>; - handler = "button_interrupt"; - }; - int_vol_up: vol_up { - irq-pin = <&gpio_volup_btn_odl>; - flags = <GPIO_INT_EDGE_BOTH>; - handler = "button_interrupt"; - }; - int_wp_l: wp_l { - irq-pin = <&gpio_ec_wp_odl>; - flags = <GPIO_INT_EDGE_BOTH>; - handler = "switch_interrupt"; - }; - int_lid_open: lid_open { - irq-pin = <&gpio_lid_open>; - flags = <GPIO_INT_EDGE_BOTH>; - handler = "lid_interrupt"; - }; - int_tablet_mode: tablet_mode { - irq-pin = <&gpio_tablet_mode_l>; - flags = <GPIO_INT_EDGE_BOTH>; - handler = "gmr_tablet_switch_isr"; - }; - int_imu: ec_imu { - irq-pin = <&gpio_imu_int_l>; - flags = <GPIO_INT_EDGE_FALLING>; - handler = "bmi3xx_interrupt"; - }; - int_lid_imu: lid_imu { - irq-pin = <&gpio_acc_int_l>; - flags = <GPIO_INT_EDGE_FALLING>; - handler = "bma4xx_interrupt"; - }; - int_usb_c0: usb_c0 { - irq-pin = <&gpio_usb_c0_int_odl>; - flags = <GPIO_INT_EDGE_FALLING>; - handler = "usb_c0_interrupt"; - }; - int_usb_c1: usb_c1 { - irq-pin = <&gpio_sb_1>; - flags = <GPIO_INT_EDGE_FALLING>; - handler = "usb_c1_interrupt"; - }; - }; - - unused-pins { - compatible = "unused-gpios"; - unused-gpios = <&gpioc 3 0>, - <&gpiod 4 0>, - <&gpiod 7 0>, - <&gpioh 2 0>, - <&gpioj 7 0>, - <&gpiol 4 0>; - }; - - named-gpios { - /* - * EC doesn't take any specific action on CC/SBU disconnect due to - * fault, but this definition is useful for hardware testing. - */ - gpio_usb_c0_prot_fault_odl: usb_c0_prot_fault_odl { - gpios = <&gpiok 6 GPIO_INPUT_PULL_UP>; - }; - - gpio_sb_1: sb_1 { - gpios = <&gpioe 6 0>; - no-auto-init; - }; - gpio_sb_2: sb_2 { - gpios = <&gpiof 0 0>; - no-auto-init; - }; - - gpio_sb_3: sb_3 { - gpios = <&gpioe 7 0>; - no-auto-init; - }; - gpio_sb_4: sb_4 { - gpios = <&gpioe 0 0>; - no-auto-init; - }; - }; - - temp_memory: memory { - compatible = "cros-ec,temp-sensor-thermistor"; - thermistor = <&thermistor_3V3_51K1_47K_4050B>; - adc = <&adc_temp_sensor_1>; - }; - temp_charger: charger { - compatible = "cros-ec,temp-sensor-thermistor"; - thermistor = <&thermistor_3V3_51K1_47K_4050B>; - adc = <&adc_temp_sensor_2>; - }; - temp_ambient: ambient { - compatible = "cros-ec,temp-sensor-thermistor"; - thermistor = <&thermistor_3V3_51K1_47K_4050B>; - adc = <&adc_temp_sensor_3>; - }; - - named-temp-sensors { - compatible = "cros-ec,temp-sensors"; - memory { - temp_fan_off = <35>; - temp_fan_max = <60>; - temp_host_high = <85>; - temp_host_halt = <90>; - temp_host_release_high = <80>; - power-good-pin = <&gpio_ec_soc_dsw_pwrok>; - sensor = <&temp_memory>; - }; - charger { - temp_fan_off = <35>; - temp_fan_max = <60>; - temp_host_high = <85>; - temp_host_halt = <90>; - temp_host_release_high = <80>; - power-good-pin = <&gpio_ec_soc_dsw_pwrok>; - sensor = <&temp_charger>; - }; - ambient { - temp_fan_off = <35>; - temp_fan_max = <60>; - temp_host_high = <85>; - temp_host_halt = <90>; - temp_host_release_high = <80>; - power-good-pin = <&gpio_ec_soc_dsw_pwrok>; - sensor = <&temp_ambient>; - }; - }; - - usba { - compatible = "cros-ec,usba-port-enable-pins"; - /* - * sb_2 is only configured as GPIO when USB-A1 is present, - * but it's still safe to control when disabled. - * - * ILIM_SEL pins are referred to by legacy enum name, - * GPIO_USB*_ILIM_SEL. The one for port A1 is unused on - * sub-boards that don't have USB-A so is safe to control - * regardless of system configuration. - */ - enable-pins = <&gpio_en_usb_a0_vbus &gpio_sb_2>; - status = "okay"; - }; - - usbc { - #address-cells = <1>; - #size-cells = <0>; - - port0@0 { - compatible = "named-usbc-port"; - reg = <0>; - bc12 = <&bc12_port0>; - chg = <&chg_port0>; - usb-mux-chain-0 { - compatible = "cros-ec,usb-mux-chain"; - usb-muxes = <&virtual_mux_0>; - }; - }; - port0-muxes { - virtual_mux_0: virtual-mux-0 { - compatible = "cros-ec,usbc-mux-virtual"; - }; - }; - port1@1 { - compatible = "named-usbc-port"; - reg = <1>; - bc12 = <&bc12_port1>; - chg = <&chg_port1>; - usb-mux-chain-1 { - compatible = "cros-ec,usb-mux-chain"; - usb-muxes = <&virtual_mux_1 &tcpci_mux_1>; - }; - usb_mux_chain_1_no_mux: usb-mux-chain-1-no-mux { - compatible = "cros-ec,usb-mux-chain"; - alternative-chain; - usb-muxes = <&virtual_mux_1>; - }; - }; - port1-muxes { - virtual_mux_1: virtual-mux-1 { - compatible = "cros-ec,usbc-mux-virtual"; - }; - tcpci_mux_1: tcpci-mux-1 { - compatible = "parade,usbc-mux-ps8xxx"; - }; - }; - }; -}; - -&gpio_acc_int_l { - gpios = <&gpioc 0 (GPIO_INPUT | GPIO_VOLTAGE_1P8)>; -}; -&gpio_imu_int_l { - gpios = <&gpioj 0 (GPIO_INPUT | GPIO_VOLTAGE_1P8)>; -}; -&gpio_vccin_aux_vid0 { - gpios = <&gpiod 0 (GPIO_INPUT | GPIO_VOLTAGE_1P8)>; -}; -&gpio_vccin_aux_vid1 { - gpios = <&gpiok 1 (GPIO_INPUT | GPIO_VOLTAGE_1P8)>; -}; - -&gpio_ec_prochot_odl { - gpios = <&gpioi 1 (GPIO_ODR_HIGH | GPIO_VOLTAGE_1P8)>; -}; - -&thermistor_3V3_51K1_47K_4050B { - status = "okay"; -}; - -&adc_ec_vsense_pp3300_s5 { - /* - * Voltage divider on input has 47k upper and 220k lower legs with 3 V - * full-scale reading on the ADC. Apply the largest possible multiplier - * (without overflowing int32) to get the best possible approximation - * of the actual ratio, but derate by a factor of two to ensure - * unexpectedly high values won't overflow. - */ - mul = <(715828 / 2)>; - div = <(589820 / 2)>; -}; - -&adc0 { - pinctrl-0 = <&adc0_ch0_gpi0_default - &adc0_ch2_gpi2_default - &adc0_ch3_gpi3_default - &adc0_ch13_gpl0_default - &adc0_ch14_gpl1_default>; - pinctrl-names = "default"; -}; - -&pinctrl { - i2c4_clk_gpe0_sleep: i2c4_clk_gpe0_sleep { - pinmuxs = <&pinctrle 0 IT8XXX2_ALT_DEFAULT>; - }; - i2c4_data_gpe7_sleep: i2c4_data_gpe7_sleep { - pinmuxs = <&pinctrle 7 IT8XXX2_ALT_DEFAULT>; - }; - i2c2_clk_gpf6_default: i2c2_clk_gpf6_default { - gpio-voltage = "1v8"; - }; - i2c2_data_gpf7_default: i2c2_data_gpf7_default { - gpio-voltage = "1v8"; - }; -}; - -&i2c0 { - label = "I2C_EEPROM"; - clock-frequency = <I2C_BITRATE_FAST>; - - cbi_eeprom: eeprom@50 { - compatible = "atmel,at24"; - reg = <0x50>; - size = <2048>; - pagesize = <16>; - address-width = <8>; - timeout = <5>; - }; - pinctrl-0 = <&i2c0_clk_gpb3_default - &i2c0_data_gpb4_default>; - pinctrl-names = "default"; -}; - -&i2c1 { - label = "I2C_BATTERY"; - clock-frequency = <50000>; - pinctrl-0 = <&i2c1_clk_gpc1_default - &i2c1_data_gpc2_default>; - pinctrl-names = "default"; -}; - -&i2c2 { - label = "I2C_SENSOR"; - clock-frequency = <I2C_BITRATE_FAST>; - pinctrl-0 = <&i2c2_clk_gpf6_default - &i2c2_data_gpf7_default>; - pinctrl-names = "default"; -}; - -&i2c4 { - label = "I2C_SUB_C1_TCPC"; - clock-frequency = <I2C_BITRATE_FAST_PLUS>; - pinctrl-0 = <&i2c4_clk_gpe0_default - &i2c4_data_gpe7_default>; - pinctrl-1 = <&i2c4_clk_gpe0_sleep - &i2c4_data_gpe7_sleep>; - pinctrl-names = "default", "sleep"; - - bc12_port1: pi3usb9201@5f { - compatible = "pericom,pi3usb9201"; - status = "okay"; - reg = <0x5f>; - }; - - chg_port1: sm5803@32 { - compatible = "siliconmitus,sm5803"; - status = "okay"; - reg = <0x32>; - }; -}; - -&i2c_ec_i2c_sub_usb_c1 { - /* - * Dynamic speed setting is used for AP-controlled firmware update - * of PS8745 TCPC/redriver: the AP lowers speed to 400 kHz in order - * to use more efficient window programming, then sets it back when - * done. - */ - dynamic-speed; -}; - -&i2c5 { - label = "I2C_USB_C0_TCPC"; - clock-frequency = <I2C_BITRATE_FAST_PLUS>; - pinctrl-0 = <&i2c5_clk_gpa4_default - &i2c5_data_gpa5_default>; - pinctrl-names = "default"; - - bc12_port0: pi3usb9201@5f { - compatible = "pericom,pi3usb9201"; - status = "okay"; - reg = <0x5f>; - }; - - chg_port0: sm5803@32 { - compatible = "siliconmitus,sm5803"; - status = "okay"; - reg = <0x32>; - }; -}; - -&usbpd0 { - status = "okay"; -}; |