summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
* util/uut: Fix resource leakPatrick Georgi2018-07-301-0/+1
* util/iteflash: Fix resource leakPatrick Georgi2018-07-301-0/+1
* bip: Add charger temp sensorJustin TerAvest2018-07-305-1/+83
* bq25710: Add bq25710 charger driverScott Collyer2018-07-294-0/+452
* scarlet: Bump the hard-coded battery currentPhilip Chen2018-07-291-1/+1
* DragonEgg: Add power sequencing supportScott Collyer2018-07-276-10/+163
* icelake: Add power sequencing support for icelakeScott Collyer2018-07-275-1/+195
* bip: Add battery temp sensorJustin TerAvest2018-07-272-0/+6
* g: speed up CCD UART processingVadim Bendebury2018-07-273-29/+41
* meep: create initial EC imageDiana Z2018-07-278-0/+694
* chip/npcx: Add command to dump flash chip infoFurquan Shaikh2018-07-271-2/+19
* baseboard/octopus: Select flash chip W25Q80Furquan Shaikh2018-07-271-1/+1
* octopus: remove unused usb_pd_policy filesJett Rink2018-07-278-37/+1
* stats_manager: prepare StatsManager to be a utility used in hdctoolsRuben Rodriguez Buchillon2018-07-274-34/+207
* servo_micro: increase stack sizeMatthew Blecker2018-07-271-1/+1
* espi: Rename CONFIG_HOSTCMD_ESPI_VW_SIGNALS to CONFIG_HOSTCMD_ESPI_VW_SLP_SIG...Furquan Shaikh2018-07-2726-38/+41
* chip/mchp: Get rid of unused lpc_host_resetFurquan Shaikh2018-07-271-22/+0
* chip/it83xx: Use CONFIG_HOSTCMD_ESPI to decide PLTRST usageFurquan Shaikh2018-07-271-3/+3
* nocturne: Enable sensor IRQs in S0.Aseda Aboagye2018-07-261-0/+4
* bobba: add bobba to flash_ec scriptJett Rink2018-07-261-0/+1
* Revert "charge_manager: allow finding supply with VOLT > 0 and CUR = 0"Devin Lu2018-07-261-1/+2
* cheza: Remove the switchcap hackWai-Hong Tam2018-07-263-13/+1
* cheza: Enable PWM for display backlightWai-Hong Tam2018-07-263-1/+18
* cheza: Change the I2C buses of BC 1.2 chipsWai-Hong Tam2018-07-261-3/+4
* cheza: Enable ADC channelsWai-Hong Tam2018-07-263-2/+44
* cheza: Change GPIO for the rev-1 boardWai-Hong Tam2018-07-262-17/+22
* Phaser: the XYZ value of base sensor is unconverted after opening lid(system ...lancangyi2018-07-261-1/+1
* phaser: remove GPIO_PULL_UP of volume buttonsnickchen2018-07-261-2/+2
* octopus: Add phaser LED behavior supporteddylu2018-07-269-12/+202
* rammus: initial setup for ecZhuohao Lee2018-07-269-0/+2262
* flash_ec: Restore *_ec3po_interp_connect on cleanup()Stephen Boyd2018-07-261-10/+4
* reset: Log the reason for AP resets.Jonathan Brandmeyer2018-07-2630-87/+447
* F75303: Set fake temperatureTino Liu2018-07-261-0/+41
* Revert "ec-devutils: update pyusb to 1.0.2"Nick Sanders2018-07-265-24/+13
* anx7447: configure VCONN OCP(Over Current Protection) threshold.Xin Ji2018-07-252-0/+15
* power: Add power_get_state APIDaisuke Nojiri2018-07-252-0/+12
* Nami: Disable ACPI and host event log messagesDaisuke Nojiri2018-07-251-0/+6
* nocturne: Enable DPTF support.Aseda Aboagye2018-07-251-0/+2
* The IT8320DX support 512KB internal flash.Donald Huang2018-07-251-10/+297
* cr50: disable ccd ports when ext ccd is disabledMary Ruthven2018-07-251-1/+6
* fpsensor: don't try to match without templatesNicolas Norvez2018-07-251-3/+4
* kukui: Disable eMMC power supply on bootNicolas Boichat2018-07-251-1/+5
* cr50: wait for RBOX_WAKEUP_INTR to be clearedMary Ruthven2018-07-252-5/+14
* bip: correct ADC scaling factorsJett Rink2018-07-251-6/+16
* common/flash: Abort rwsig when RW is erased/written toNicolas Boichat2018-07-252-2/+20
* keyboard_8042: Clear buffer before adding command byteFurquan Shaikh2018-07-251-0/+7
* nocturne: Restart base detection in S3.Aseda Aboagye2018-07-251-4/+4
* tcpm: wait for TCPC to init upon first tcpc accessJett Rink2018-07-255-53/+229
* Phaser: three SKU IDs used, 1(phaser), 2(phaser360), 3(phaser360s)lancangyi2018-07-241-1/+1
* Nami: Reverse polarity of USB2_IDDaisuke Nojiri2018-07-242-3/+2
View Lorry Controller Status