summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
...
* CEC: Add CEC APIStefan Adolfsson2018-05-092-0/+71
* phaser: initial files commitJett Rink2018-05-098-0/+368
* tablet_mode: Define common interrupt handler for tablet switchDaisuke Nojiri2018-05-096-7/+69
* Nami: Use lid angle to detect tablet mode for Vayne & NamiDaisuke Nojiri2018-05-092-98/+103
* cheza: Remove BC1.2 switch hackTom Wai-Hong Tam2018-05-091-14/+0
* cheza: Support PD and chargingTom Wai-Hong Tam2018-05-099-13/+885
* anx7447: remove write to OCM version regJett Rink2018-05-091-1/+0
* fpsensor: export matched finger indexVincent Palatin2018-05-093-4/+12
* npcx: system: Add chip generation info in system_get_chip_revision().Mulin Chao2018-05-091-6/+29
* cheza: Change ACOK_OD pin to EC inputTom Wai-Hong Tam2018-05-081-5/+5
* cheza: Lower the I2C bus speed of smart batteryTom Wai-Hong Tam2018-05-081-1/+1
* cheza: Remove internal pull-up for the BATT_PRES_ODL pinTom Wai-Hong Tam2018-05-081-1/+1
* yorp: renegotiate Vbus down before hibernatingJett Rink2018-05-082-21/+46
* cheza: Support confirmation of power lostTom Wai-Hong Tam2018-05-083-3/+60
* cheza: Enable AP_RST_REQ as a request from AP to reset itselfWai-Hong Tam2018-05-084-2/+37
* meowth_fp: make FP_RST_ODL push-pullVincent Palatin2018-05-081-1/+1
* atlas: config PROCHOT GPIO as inputCaveh Jalali2018-05-081-1/+1
* charger: set PPVAR_SYS to normal battery voltageCaveh Jalali2018-05-081-1/+1
* shared_mem: Assert that shared memory size is large enoughNicolas Boichat2018-05-0711-5/+59
* cr50: disable s3_terms during initMary Ruthven2018-05-071-4/+28
* anx7447: Set mux for USB3.0 devicesDaisuke Nojiri2018-05-071-16/+29
* Nami: Disable ALS for AkaliTino Liu2018-05-071-2/+3
* yorp: Configure GPIO_HIB_WAKE_HIGH for AC_PRESENTFurquan Shaikh2018-05-071-2/+4
* yorp: Enable SINK_CTRL on PPC before hibernatingFurquan Shaikh2018-05-071-1/+9
* cr50_rma_open: add support for testlab modeMary Ruthven2018-05-041-0/+87
* CBI: Disallow board version and OEM ID to be reprogrammedDaisuke Nojiri2018-05-043-3/+15
* yorp: Shutdown AP when doing hibernateFurquan Shaikh2018-05-041-0/+12
* eve: Limit data role swap to port 0Duncan Laurie2018-05-041-0/+4
* cheza: Make sure switchcap is configured rightAlexandru M Stan2018-05-043-1/+13
* cheza: Add SDM845 power sequence for rev-0 boardWai-Hong Tam2018-05-047-2/+677
* octopus: move more implementation to baseboardJett Rink2018-05-0412-368/+428
* octopus: remove pwm code for LEDsJett Rink2018-05-042-6/+0
* stm: inline raw_read8 in header fileJett Rink2018-05-043-35/+26
* flash_ec: Add nocturne board.Aseda Aboagye2018-05-041-0/+1
* yorp: Add support for SONY batteryDivya Sasidharan2018-05-042-0/+29
* usb_pd_protocol: Add PD_ROLE_DISCONNECTED for data role swapsDuncan Laurie2018-05-032-2/+8
* nocturne: Only power base when AP is on.Aseda Aboagye2018-05-031-16/+46
* sweetberry: Make resetting USB interface more forgivingPuthikorn Voravootivat2018-05-031-9/+9
* cr50_rma_open: add support for checking prepvt and prod versionsMary Ruthven2018-05-021-4/+11
* ectool: add 'kbinfo' commandBrian Norris2018-05-021-0/+26
* PRESUBMIT: give real namesBrian Norris2018-05-021-3/+3
* ectool: Add hibernate-clear-ap-off commandRaul E Rangel2018-05-021-2/+4
* yorp: Control backlight based on chipset transitionsFurquan Shaikh2018-05-022-0/+13
* ec: Add .clang-formatRaul E Rangel2018-05-021-0/+10
* gsctool: add verbose mode command line optionVadim Bendebury2018-05-021-1/+7
* gsctool: add version command line optionVadim Bendebury2018-05-023-4/+26
* cr50: prepare to release prepvt 0.4.6Vadim Bendebury2018-05-021-1/+1
* octopus: move common function to baseboardJett Rink2018-05-023-146/+92
* octopus: move common CONFIG defines into baseboardJett Rink2018-05-024-285/+258
* build: add build option to print configsJett Rink2018-05-021-0/+15
View Lorry Controller Status