summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
* octopus: Add phaser LED behavior supporteddylu2018-07-269-12/+202
* rammus: initial setup for ecZhuohao Lee2018-07-269-0/+2262
* flash_ec: Restore *_ec3po_interp_connect on cleanup()Stephen Boyd2018-07-261-10/+4
* reset: Log the reason for AP resets.Jonathan Brandmeyer2018-07-2630-87/+447
* F75303: Set fake temperatureTino Liu2018-07-261-0/+41
* Revert "ec-devutils: update pyusb to 1.0.2"Nick Sanders2018-07-265-24/+13
* anx7447: configure VCONN OCP(Over Current Protection) threshold.Xin Ji2018-07-252-0/+15
* power: Add power_get_state APIDaisuke Nojiri2018-07-252-0/+12
* Nami: Disable ACPI and host event log messagesDaisuke Nojiri2018-07-251-0/+6
* nocturne: Enable DPTF support.Aseda Aboagye2018-07-251-0/+2
* The IT8320DX support 512KB internal flash.Donald Huang2018-07-251-10/+297
* cr50: disable ccd ports when ext ccd is disabledMary Ruthven2018-07-251-1/+6
* fpsensor: don't try to match without templatesNicolas Norvez2018-07-251-3/+4
* kukui: Disable eMMC power supply on bootNicolas Boichat2018-07-251-1/+5
* cr50: wait for RBOX_WAKEUP_INTR to be clearedMary Ruthven2018-07-252-5/+14
* bip: correct ADC scaling factorsJett Rink2018-07-251-6/+16
* common/flash: Abort rwsig when RW is erased/written toNicolas Boichat2018-07-252-2/+20
* keyboard_8042: Clear buffer before adding command byteFurquan Shaikh2018-07-251-0/+7
* nocturne: Restart base detection in S3.Aseda Aboagye2018-07-251-4/+4
* tcpm: wait for TCPC to init upon first tcpc accessJett Rink2018-07-255-53/+229
* Phaser: three SKU IDs used, 1(phaser), 2(phaser360), 3(phaser360s)lancangyi2018-07-241-1/+1
* Nami: Reverse polarity of USB2_IDDaisuke Nojiri2018-07-242-3/+2
* kukui: Support command to enable/disable eMMC power.Yilun Lin2018-07-241-0/+25
* charger/mt6370: Support set LDO voltage function.Yilun Lin2018-07-242-0/+50
* Fleex: Enable volume control functionRaymond Chou2018-07-243-0/+10
* bip: Add temperature sensor supportJustin TerAvest2018-07-233-0/+25
* Cr50: Fix _plat__StartupCallback()Nicolas Boichat2018-07-231-1/+1
* charge_manager: Code cleanupVijay Hiremath2018-07-231-17/+11
* ectool: Handle "Dead pixels: UNKNOWN" in "fpinfo"Nicolas Norvez2018-07-232-3/+12
* f75303: Simplify f75303_get_val APIDaisuke Nojiri2018-07-232-30/+17
* Nami: Add local sensor of F75303 for AkaliDaisuke Nojiri2018-07-232-9/+73
* kukui: Use MODULE_SPI_FLASH for eMMC emulation pinsNicolas Boichat2018-07-232-2/+2
* power/mt8183: Fix PMIC_EN_ODL polarity, watchdog signalNicolas Boichat2018-07-232-3/+3
* kukui: Remap DMA channel 6/7 to SPI2Nicolas Boichat2018-07-231-2/+4
* board: Clean up DMA channel mappingNicolas Boichat2018-07-236-19/+15
* kukui: Disable CONFIG_STM32_CLOCK_LSENicolas Boichat2018-07-231-1/+0
* config: Clarify CONFIG_STM32_CLOCK_LSE is sourced externallyNicolas Boichat2018-07-233-2/+10
* Revert "g: speed up CCD UART processing"Mary Ruthven2018-07-213-42/+30
* cr50: prepare to release 0.4.9Vadim Bendebury2018-07-211-1/+1
* yorp: Add PSL supportScott Collyer2018-07-202-0/+28
* cleanup: Resolve some defects seen with Coverity.Jonathan Brandmeyer2018-07-203-4/+5
* octopus: Enable auto toggle/low power mode for standalone tcpcsScott Collyer2018-07-201-6/+2
* IT8320DX: espi: reset espi module by FWDino Li2018-07-203-4/+58
* kukui: Fix bmi160 i2c2 config on wrong GPIO PIN.Yilun Lin2018-07-201-2/+2
* ppc: remove EC ability to drive PPC GPIOJett Rink2018-07-202-41/+12
* aleena,liara: Add new grunt-family boards.stabilize-10895.Bstabilize-10895.56.Brelease-R69-10895.BEdward Hill2018-07-2014-0/+1514
* Nami: Disable Accel/Gyro sensor for clamshellsDaisuke Nojiri2018-07-203-8/+20
* whiskers: enable heatmap interfaceWei-Han Chen2018-07-201-4/+20
* bq25703: Fix charge ramp issueVijay Hiremath2018-07-192-31/+90
* cr50: fix prod RMA reset p256 key idVadim Bendebury2018-07-191-1/+1
View Lorry Controller Status