summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
...
* TCPMv2: Adjust sink hard reset behaviorDiana Z2021-02-012-16/+39
* eldrid: remove CONFIG_SYSTEM_UNLOCKEDScott Chao2021-02-011-1/+1
* vilboz: modify charger input current limit settingSamsp_Liu2021-02-011-0/+15
* vilboz: enable USB 3 mux for the LTE modemVincent Palatin2021-02-011-0/+19
* lindar: modify led behaviorjerry2.huang2021-02-012-8/+8
* magolor: Remove CONFIG_SYSTEM_UNLOCKEDBen Chen2021-02-011-6/+0
* NCT3807: Enable full VCONN protectionJacky Wang2021-02-012-0/+20
* aleena: Add detect accel/gyro sensor in HOOK_INITDavid Huang2021-02-011-0/+3
* zork: add SSFC field for auto-mode speaker ampPeter Marheine2021-02-012-12/+23
* device_event: Don't notify host of disabled events (2)Daisuke Nojiri2021-01-301-9/+11
* zephyr: kohaku: Update build for flashYuval Peress2021-01-302-0/+11
* zephyr: Add configuration for RAM sizeYuval Peress2021-01-303-0/+22
* device_event: Don't notify host of disabled eventsDaisuke Nojiri2021-01-302-0/+12
* dartmonkey: Refactor GPIOs to keep RO minimalTom Hughes2021-01-309-126/+188
* Dedede: Add RAA489000 output current settingDiana Z2021-01-297-6/+50
* Zephyr: Add LID_ANGLE_UPDATE supportHyungwoo Yang2021-01-293-5/+23
* Update FPMCU console UART name and power railTom Hughes2021-01-292-5/+5
* util/flash_ec: Clean up FPMCU flashingTom Hughes2021-01-291-13/+42
* zephyr: add PWM shimKeith Short2021-01-2910-1/+308
* zephyr: add HOOKS taskKeith Short2021-01-297-1/+81
* Galtic: Add TCPC dump commandDiana Z2021-01-291-0/+1
* TCPMv2: Check message discard sending Vconn swap PS_RDYDiana Z2021-01-291-0/+3
* fpsensor: Move CONFIG_CMD_SPI_XFER to RWTom Hughes2021-01-292-1/+4
* fpsensor: Add FP sensor SPI detection logicTom Hughes2021-01-298-4/+69
* zephyr: zmake: add a test for BuildConfig objectsJack Rosenthal2021-01-292-0/+185
* RAA489000: Add TCPC interface to control output currentDiana Z2021-01-292-10/+33
* Metaknight: Fix g-sensor nameYu-An Chen2021-01-291-2/+2
* board: delete jerryJack Rosenthal2021-01-296-327/+0
* driver: icm426xx: Use calibration unit to set/get offsetGwendal Grignou2021-01-291-20/+13
* morphius: use different gyro sensor by ssfcZick Wei2021-01-291-7/+28
* ctn730: Add delay between INITIALIZATION and ENABLE (2)Daisuke Nojiri2021-01-292-10/+10
* Servo_V4: Remove unused commands to save flash spaceBrian J. Nemec2021-01-293-0/+12
* bobba: Fix bobba accel icm matrix.David Huang2021-01-291-1/+1
* Lazor: Modify motion sensors detectionSue Chen2021-01-291-11/+10
* zephyr: Fix kconfig license headerYuval Peress2021-01-291-3/+3
* common: motion: move read fifo console commandGwendal Grignou2021-01-292-32/+34
* Revert "ctn730: Add delay between INITIALIZATION and ENABLE"Daisuke Nojiri2021-01-292-7/+7
* vilboz: replace obsolete dalboz config macrosPeter Marheine2021-01-291-49/+7
* kindred: config motion sensor driver by chip idBen Chen2021-01-293-2/+142
* magolor: Set gyroscope translation matrixBen Chen2021-01-291-1/+1
* RAA489000: Organize header fileDiana Z2021-01-291-10/+13
* COIL: Rename variables in MT6360 driverDiana Z2021-01-293-11/+11
* zephyr: increase task stacks size for few threads close to the limitFabio Baltieri2021-01-281-4/+4
* driver: rt1715 : Improve noise rejectionBen Chen2021-01-282-19/+172
* sasuke : add retimer to port 0YongBeum.Ha2021-01-281-0/+7
* zephyr: volteer: add forgotten power sequencing interruptJack Rosenthal2021-01-281-0/+1
* ctn730: Add delay between INITIALIZATION and ENABLEDaisuke Nojiri2021-01-282-7/+7
* CoachZ: Pull down WLC IRQDaisuke Nojiri2021-01-281-5/+4
* Volteer: Add support for FRS to C1Eric Herrmann2021-01-285-0/+8
* CoachZ: Wake up system when stylus is attachedDaisuke Nojiri2021-01-281-1/+2